基于最短路径的SCI网络拓扑结构研究

 从航空电子系统的需求出发,对可扩展一致性接口(SCI)网络的拓扑结构进行了最短路径（跳数）研究。利用图论中的邻接矩阵变换方法,根据航空电子系统中SCI节点端口数的限制及SCI网络的小环组合结构的特点,对SCI推荐的网格形和蝶形两种网络进行了平均最小跳数的计算和分析,得出了SCI网络中小环方向的改变对平均最小跳数有影响的结论,并得到了该两种网络结构中平均最小跳数最少的拓扑形式。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

Autonomous Control Reconfiguration of Aerospace Vehicle Based on Control Effectiveness Estimation

未来空天飞行器跨空天两域飞行,要求有较高的自主性以适应由故障和环境变化带来的不确定因素。针对空天飞行器的不确定性,提出了自主控制重构方案。研究了线性模型的时变控制效益的估计方法,提出并证明了效益矩阵可估计的充分条件,给出了相应的算法并证明了其收敛性和对噪声的鲁棒性;提出了基于线性规划和模糊逻辑的控制分配算法,通过冗余效应器实现了不确定条件下的自主控制重构。系统集成和仿真结果分析验证了方案和算法的有效性。     

不确定参数结构特征值问题的概率统计方法和区间分析方法的比较

 基于区间数学理论、灵敏度分析理论、Kronecker代数理论,应用Taylor级数展开、概率摄动技术,提出了具有不确定参数结构的特征值问题的区间分析方法。结合工程实例与传统的概率分析方法进行比较,给出了两种方法的数值解法及各自解法的Kronecker代数形式。数值算例的结果显示了区间分析方法在具有不确定参数结构特征值问题分析中的价值和有效性。     

超低轨道卫星应用离子电推进技术方案

低地球轨道大气环境对诸如科学探测和对地观测卫星的阻尼作用十分明显,而且阻尼随太阳和地磁活动以及昼夜、季节交替变化范围宽.为了保证卫星轨道精度或飞行状态满足任务要求,需要利用推进系统对卫星受到的阻尼进行实时或间歇式补偿以实现轨道或飞行状态的保持.针对轨道高度220～268 km的无拖曳飞行和轨道维持应用,基于卫星轨道阻尼...     

面向对象技术的防空导弹Simulink建模与仿真

为防空导弹系统性能改进研究和优化设计,提出了一种新的方法,首先给出了一般防空导弹制导控制系统的数学模型,并采用面向对象建模技术结合动态仿真软件Simulink建立了仿真模型并进行了仿真研究,该模型具有容易理解,可重复使用,易于扩展等优点,即通过部分模块更换或改变参数等就可对该系统在其他条件下进行仿真,仿真结果和实际遥测数据基本吻合,表明了该模型和方法的有效性和实用性。     

包带低冲击装置冲击试验及数据分析

文章主要阐述了包带低冲击装置冲击试验的过程及采用的试验技术,并对试验数据进行了处理和分析。通过大量的试验数据,对响应量级与测量点的位置分布、响应与包带预紧力的关系、冲击响应与装药量的关系、冲击响应与起爆器的关系、冲击响应的频率分布关系以及安装方式对试验结果产生的影响作了充分的分析。结果可为研究低冲击装置提供有价值的参考。     

嫦娥一号月球探测卫星研制综述

嫦娥一号卫星是我国第一个月球探测卫星,将实现对月球的环绕探测。嫦娥一号卫星的研制和发射是我国深空探测活动的开端,在我国航天史上将成为继人造卫星和载人航天后的第三个里程碑。与近地卫星相比,嫦娥一号卫星面临更复杂的控制过程和环境,因此,嫦娥一号卫星必须突破一系列的关键技术,实现既定的任务目标。文章介绍了嫦娥一号卫星的任务目标、主要技术方案和研制过程;概要性地说明了嫦娥一号卫星的研制过程。