Prediction of shock-layer ultraviolet radiation for hypersonic vehicles in near space

A systemic and validated model was developed to predict ultraviolet spectra features from the shock layer of near-space hypersonic vehicles in the ‘‘solar blind" band region. Computational procedures were performed with 7-species thermal non-equilibrium fluid mechanics, finite rate chemistry, and radiation calculations. The thermal non-equilibrium flow field was calculated with a two-temperature model by the finite volume technique and verified against the bow-shock ultra-violet(BSUV) flight experiments. The absorption coefficient of the mixture gases was evaluated with a line-by-line method and validated through laboratory shock tube measurements. Using the line of sight(LOS) method, radiation was calculated from three BSUV flights at altitudes of 38,53.5 and 71 km. The investigation focused on the level and structure of ultraviolet spectra radiated from a NO band system in wavelengths of 200–400 nm. Results predicted by the current model show qualitative spatial agreement with the measured data. At a velocity of 3.5 km/s(about Mach11), the peak absolute intensity at an altitude of 38 km is two orders of magnitude higher than that at 53.5 km. Under the same flight conditions, the spectra structures have quite a similar distribution at different viewing angles. The present computational model performs well in the prediction of the ultraviolet spectra emitted from the shock layer and will contribute to the investigation and analysis of radiative features of hypersonic vehicles in near space.     

一种修正的Osher通量在高阶WCNS中的特性

将一种基于多维修正的Osher通量运用于高阶加权紧致非线性格式(WCNS)中,该修正通量主要在垂直于激波面的界面上增加耗散,能够改善Osher通量的激波捕捉稳定性,同时对边界层和接触间断的分辨率影响非常小。对修正的Osher通量在高阶WCNS中的特性进行研究,通过数值模拟测试了基于Osher通量的WCNS的激波稳定性、热流预测精度、边界层模拟能力、激波边界层干扰模拟能力,并与Steger-Warming通量和Roe通量进行了对比。结果表明修正后的Osher通量比Harten修正的Roe通量具有更好的激波捕捉鲁棒性,而边界层、驻点热流值和激波边界层干扰的模拟则明显优于Steger-Warming通量。上述结果说明了基于修正的Osher通量的高阶WCNS具有较好的激波捕捉特性、热流预测精度和边界层计算能力。     

陶瓷隔热瓦的缺陷修补

分别采用了MgO、YSZ和Al₂O₃三种陶瓷粉体和一种含隔热瓦本体成分的粉料对陶瓷隔热瓦缺陷进行修补。研究了修补前后材料的微观形貌、力学及隔热性能。结果表明：采用含隔热瓦本体组成的粉料对陶瓷隔热瓦进行修补,修补部位与本体部位相容性好,且微观形貌相似,仍保持纤维搭接的多孔空间网络结构;修补后试样密度0.24 g/cm³、室温热导率0.044 W/（m·K）、压缩强度0.58 MPa;1 200℃、30 min热处理后,修补部位与本体部位结合性好,未出现裂纹、凹陷等缺陷,是有效的缺陷修补方法。     

航空发动机风扇叶片两种表面处理方法对比

在对激光冲击强化技术与喷丸表面强化技术比较分析之后,表明航空发动机叶片经过激光冲击强化后,能显著增加叶片表面残余压应力,提高疲劳性能,并且其效果优于喷丸表面强化技术。     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

包带低冲击装置冲击试验及数据分析

文章主要阐述了包带低冲击装置冲击试验的过程及采用的试验技术,并对试验数据进行了处理和分析。通过大量的试验数据,对响应量级与测量点的位置分布、响应与包带预紧力的关系、冲击响应与装药量的关系、冲击响应与起爆器的关系、冲击响应的频率分布关系以及安装方式对试验结果产生的影响作了充分的分析。结果可为研究低冲击装置提供有价值的参考。     

高效空间应用燃料电池热能利用技术研究

首先介绍了空间应用燃料电池高效散热及温控技术。高精度控温主要是利用被动散热技术,将产生的热量快速传导至外部冷却介质,从而保证产热面的温度均匀性,实现电池稳定工作。通过嵌入式被动散热和双端散热的冷却方式,实现电堆内部最大温差小于5℃,换热系数达1000W/(m·K)。     

数值仿真技术在热真空试验中的应用

由于热真空试验中温度测点有限,且关键部位布置困难,不能反映试验过程部件整体和关键部位的温度结果,导致试验有效性和产品安全性难以判断。通过数值仿真技术对试验过程进行模拟,得到所有部件详细温度场,验证试验有效性与产品安全性;发现影响产品温度分布的因素,研究提高产品可靠性措施。通过对某天线热真空试验过程模拟,得到天线详细温度场,并发现产品散热板安装＂不紧密＂缺陷,是影响天线温度均匀性的＂关键点＂。     

Shock protection of penetrator-based instrumentation via a sublimation approach

It is often necessary for space-borne instrumentation to cope with substantial levels of shock acceleration both in the initial launch phase, as well as during entry, descent and landing in the case of planetary exploration. Current plans for a new generation of penetrator-based space missions will subject the associated on-board instrumentation to far greater levels of shock, and ways must therefore be found to either ruggedize or else protect any sensitive components during the impact phase. In this paper, we present an innovative method of shock protection that is suited for use in a number of planetary environments, based upon the temporary encapsulation of said components within a waxy solid which may then be sublimated to return the instrument back to its normal operation. We have tested this method experimentally using micromachined silicon suspensions under applied shock loads of up to 15,000g, and found that these were able to survive without incurring damage. Furthermore, quality factor measurements undertaken on these suspensions indicate that their mechanical performance remains unaffected by the encapsulation and subsequent sublimation process.     

基于Ansys Icepak 的负载器热设计与热分析

基于热设计的基础理论与负载器的工作原理,应用Ansys Icepak仿真软件对供配电负载器工作过程中内部散热情况进行仿真,找出负载器内部温度最高部位,指导实际测试,避免实际测试的盲目性。另外,通过优化负载器散热孔设计,降低负载器温升值。