应用分力合成方法提高系统性能指标的研究

提出了将柔性结构的分力合成主动振动抑制方法和反馈控制律结合使用来提高柔性结构控制系统性能指标的方法。应用该方法仅需要知道闭环系统及柔性振动的频率及阻尼，而且可以同时抑制任意多个振动模态（包括控制器引起的振动，柔性振动及其他形式的振动），分力合成方法对频率及阻尼的不确定性具有较强的鲁棒性，使该方法易于工程实现，文章针对单柔性杆，将分力合成主动振动抑制方法和反馈控制相结合，设计了不同形式的大角度机动控制律，数值仿真和试验结果充分验证了方法的有效性。     

神舟2号大气密度探测器的探测结果(Ⅰ)日照和阴影区域热层大气密度变化

选用了神舟2号（SZ-2）大气密度探测器在2001年2—4月间的探测数据,进行日照和阴影区域热层大气密度变化的探讨.结果表明:在高度410km附近,日照和阴影区域大气密度变幅为2—3倍,变幅的大小与地磁活动程度呈负相关关系.日照面大气密度峰区位于星下点地方时1400—1500LT的纬度处,峰值大小与太阳活动程度呈正相关关系.阴影面大气密度谷区位于星下点地方时0400-0500的纬度处,同时在±10°纬度区域中还出现了阴影面峰区.     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

MONITORING OF ENERGETIC PARTICLE ENVIRONMENT INSIDE THE CHINA-BRAZIL EARTH RESOURCE SATELLITE

On 14 October 1999, the Chinese-Brazil earth resource satellite (CBERS-1) was launched in China. On board of the satellite there was an instrument designed at Peking University to detect the energetic particle radiation inside the satellite so the radiation fluxes of energetic particles in the cabin can be monitored continuously. Inside a satellite cabin, radiation environment consists of ether penetrated energetic particles or secondary radiation from satellite materials due to the interactions with primary cosmic rays.Purpose of the detectors are twofold, to monitor the particle radiation in the cabin and also to study the space radiation environment The data can be used to study the radiation environment and their effects on the electronics inside the satelhte cabin. On the other hand, the data are useful in study of geo-space energetic particle events such as solar proton events, particle precipitation and variations of the radiation belt since there should be some correlation between the radiation situation inside and outside the satellite.The instrument consists of two semi-conductor detectors for protons and electrons respectively. Each detector has two channels of energy ranges. They are 0.5-2MeV and ≥2MeV for electrons and 5-30MeV and 30-60MeV for protons. Counting rate for all channels are up to 104/(cm2@s)and power consumption is about 2.5 W. There are also the additional functions of CMOS TID (total integrated dose) effect and direct SEU monitoring. The data of CBMC was first sent back on Oct. 17 1999 and it's almost three years from then on. The detector has been working normally and the quality of data is good.The preliminary results of data analysis of CBMC not only reveal the effects of polar particle precipitation and radiation belt on radiation environment inside a satellite, but also show some important features of the geo-space energetic particle radiation.As one of the most important parameters of space weather, the energetic charged particles have great influences on space activities and ground tech nology. CBMC is perhaps the first long-term on-board special equipment to monitor the energetic particle radiation environment inside the satellite and the data it accnmulated are very useful in both satellite designing and space research.     

柱面菲涅耳太阳聚光透镜的光学设计和光学效率

研究了柱面线聚焦菲涅耳太阳聚光透镜的光学设计和光学效率。依据理论分析，对透镜参数进行了优化设计，成功地研制出了柱面线聚焦菲涅耳聚光透镜。还分析了透镜相对孔径（F数）和成型模具等因素对透镜光学效率的影响。     

高空高速无人飞行器热控制系统设计

针对飞行时间短、速度和高度变化快、表面温度波动大的无人飞行器UAV(Unmanned Aerial Vehicles)热控制系统设计难题,提出了一种可解决实际工程问题的热分析计算方法.即把热天工况、冷天工况和标准天工况作为设计/试验工况;采用参考温度法、高超音速工程预测法或计算流体动力学CFD(Computational Fluid Dynamics)数值模拟法,确定了飞行器表面温度分布,并把其作为后续热分析数学模型的外边界条件;分析结构热容量对瞬态热载荷的影响,建立与之相应的边值问题方程,并采用有限差分法求解;根据高空高速飞行特点及瞬态热载荷值,确定仪器设备舱调温系统方案.     

空间任意形状凸面的轨道空间外热流计算方法

采用蒙特卡罗（ＭｏｎｔｅＣａｒｌｏ）方法，进行了平板、半球面、抛物面的地球反照角系数和地球红外角系数计算，通过与文献数据的比较，证明了由此方法所编程序的可靠性和实用性。利用这种方法，可以计算空间任意形状凸表面的轨道空间外热流。     

基于连续覆盖特性分析的星座设计

研究了需要对地面目标进行连续覆盖的星座的设计问题．首先推导了对覆盖性能有重要影响的星间覆盖间隔时间和轨道面覆盖间隔时间的计算公式，通过算例针对不同配置的星座进行了计算，使用工程仿真软件STK验证了分析结果．通过理论分析、算例计算以及工程仿真为该类型星座设计提供了理论指导。     

飞机变形自动化测量方法研究

为解决以往飞机变形测量模式中人工干预较多,受测量环境影响较大,测量时间长等问题,基于Geo COM技术和RS232,在计算机与全站仪之间进行数据交换,设计了一套自动化测量系统。在测量过程中由标志点的机体理论坐标反算其在当前测站中的极坐标,从而在测量过程中驱动全站仪指向待测点,减少人工瞄准时间,并由计算机实时解算结果数据。经实际飞行试验验证表明,测量时间缩短为原来时间一半,大大提高了工作效率。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.