超薄层C—N共渗研究

用自行研制伯低真空化学热处理多用炉进行低真空脉冲式碳－氮共渗试验。研究渗剂组成及配比、工作压力、脉冲工艺周期、共渗温度与时间对渗层特性的影响。研究结果表明，在适当的工艺条件下，低真空脉冲式碳一氮共渗工艺能满足机械零件表面硬化层深度０．１－－０．３ｍｍ，硬度≥５８ＨＲＣ的要求。     

草酸阳极氧化新工艺及其应用

采用硫酸－草酸复合阳极氧化工艺，即在草酸阳极氧化前在硫酸溶液中氧化若干分钟，以避免零件发生烧蚀现象，同时能够提高草酸溶液的耐氯离子能力，而且适用于含铜铝合金。草酸溶液中添加１～５ｍＬ／Ｌ甲酸，可以消除氧化膜中的小白点现象。     

钢铁低温发兰,磷化液的研究

发兰，磷化是钢铁表面处理应用最为广泛的工艺。该研究得出了最新工艺配方，使发兰，磷化工艺具有低温性，低渣量，快速性，低成本的特点。     

Cutting force model and damage formation mechanism in milling of 70wt% Si/Al composite

High-mass fraction silicon aluminium composite(Si/Al composite) has unique properties of high specific strength, low thermal expansion coefficient, excellent wear resistance and weldability. It has attracted many applications in terms of radar communication, aerospace and automobile industry. However, rapid tool wear resulted from high cutting force and hard abrasion, and damaged machined surfaces are the main problem in machining Si/Al composite. This work aims to reveal the mechanisms of milli...     

Interconnected Ni（OH）2 and polyether amine on carbon fiber surface for simultaneously improving interfacial adhesion of epoxy composites and electrochemical properties

Interconnected Ni（OH）₂ nanoflakes and polyether amine（PEA） were deposited on carbon fiber tows via a facial and effective process of chemical bath deposition and dip coating. Based on this, a win–win benefit of simultaneously improvements in interfacial shear strength（IFSS） of carbon fiber/epoxy composites and the electrochemical activity has been achieved. Compared with CF and CF-Ni（OH）₂ composites, the IFSS of CF-Ni（OH）₂-PEA/epoxy composite respectively increas...     

大型空间地磁亚暴环境地面模拟试验

空间地磁亚暴环境可以给地球同步轨道卫星带来灾难性后果。文章主要介绍了地磁亚暴环境效应及国内外的相关设备,并根据我国现状,提出进行大型地磁亚暴环境试验的必要性和可行性。     

钛合金径向超声振动铣削表面粗糙度研究

为提高钛合金零件加工质量,设计了径向超声振动辅助铣削试验装置,研究了切削速度、切削深度、进给速度和超声振动幅值对钛合金零件表面粗糙度的影响规律.试验结果表明,与普通铣削相比,径向超声振动铣削后工件上的刀痕更加平整、分布更加均匀,材料去除更彻底,有效减少了由于钛合金切屑粘刀造成的表面划痕和积屑瘤等现象.在不同的切削参数下,径向超声振动铣削均可以改善钛合金零件的表面粗糙度,这一点在低速切削时更为明显,而超声振动幅值过大或过小都会影响加工质量.对加工系统的切削力进行了分析,发现超声振动辅助铣削时系统的切削力明显减小,有助于提高加工系统的稳定性,从而能够获得较好的表面质量.     

大型反射面天线温度分布规律及变形影响分析

针对高频段大型反射面天线对电性能的高要求,必须降低太阳热辐射对天线的影响。先计算一天中太阳入射角度的变化规律,再基于I\|DEAS软件仿真,得到一天中各时刻天线反射面上的温度、热应力场、热变形分布,然后针对阴影对天线结构的重要影响,以“分点分段”的形式给出不同时刻温度在反射面上的分布及其影响程度和规律,为工程人员进行天线的温度补偿和结构优化提供了依据。     

GPS total electron content and surface latent heat flux variations before the 11 March 2011 M9.0 Sendai earthquake

The present paper describes the variations of the GPS total electron content (TEC) from the International GNSS service network and surface latent heat flux (SLHF) from the Scientific Computing Division of the National Center for Atmospheric Research (NCAR) before the 11 March 2011 M9.0 Sendai earthquake, respectively. The analysis shows pronounced enhancements in the GPS TEC and SLHF a few days prior to the earthquake event. The maximum increase in the GPS TEC was about 30 TECu with an extended spatial distribution on a geomagnetically quiet day (Dst ? −20 nT, between two moderate geomagnetic storms), 8 March, 3 days prior to the earthquake. This giant positive disturbance was possibly associated with the impending disastrous earthquake and contributed from the enhanced solar radiation. Moreover, there were several anomalous regions of SLHF on the global map, but an area of enhanced SLHF very close to the epicenter. The purpose of this paper is to report the existence of the changes in surface and ionosphere, and show the potential application of multi-source data to identify seismic precursors.     

频率标准用超导铌腔内表面处理工艺研究

频率标准用超导铌腔内表面的处理是影响超导腔Q值的最大因素。本文首先通过理论分析确定了超导腔Q与表面剩余电阻的关系,其次通过一系列的表面处理工艺来保证超导腔内表面的剩余电阻尽量小,最后通过实验得到了超导腔的Q值为1.9E9,与理论计算结果相近,证明了表面处理的有效性。