轧波胀形成形工艺应用研究

介绍了轧波成形+胀形的工艺过程、设备原理及技术改进.首先用轧波成形制出工件的大概形状,然后再用胀形工艺校圆.该成形方法不仅要求工装简单,而且成形精度较高,适用于旋转环形钣金零件.     

高超声速激波/边界层干扰流动数值模拟研究

在基于Roe格式的全Navier-Stokes方程计算流体力学(CFD)代码中,发展了一种局部熵修正方法,克服了传统熵修正方法在边界层流动模拟中耗散过大的缺点,可用于更加准确的模拟激波/边界层干扰的复杂高超声速流动。对典型高超声速双锥边界层分离与激波干扰的复杂流动进行了模拟,研究了网格密度和熵修正方法耗散性对计算结果的影响。研究表明:高超声速双锥边界层分离与激波干扰流动的数值模拟结果对网格具有很强的敏感性,过稀的网格将产生严重的分离流动预测偏差;低耗散性的局部熵修正方法能更加准确地模拟复杂的高超声速激波与边界层分离流动干扰现象。     

热激励在超声速进气道内对激波诱导的边界层分离的控制机理

通过数值模拟的方法研究了马赫5的超声速进气道内,热激励对激波/边界层相互作用的控制机理。研究了热激励器放热功率(E)、热激励器展向放置数目(N)和热激励器到控制激波的距离(S)三个参数在超声速进气道内激波控制和边界层分离改善中的表现。分别针对以下四种条件进行了数值模拟:1)E=2k W、N=2、S=0.02m;2)E=3k W、N=2、S=0.02m;3)E=2k W、N=3、S=0.02m;4)E=2k W、N=2、S=0m。分析发现:在以上四种条件下,均可观察到热激励在控制激波和改善激波诱导边界层分离上有着显著的效果。热激励器的放热功率对激波的控制效果有着明显的影响,在本文所考虑的热激励能量范围内,放热功率越大,原激波角的改变越大,最终分离区的改变越明显;展向放置的热激励器数目N影响着输入到流场的能量密度,并且N越大,壁面附近的激波面越趋于平面。尽管N对上壁面沿展向的压力分布无明显影响,但对上壁面分离区大小有明显的影响;对比条件1和4下的计算结果,发现S=0.02m可以得到很好的控制效果,而S=0m时流场结构几乎没有变化,这就表明热激励器必须放置在控制激波上游的一定距离处才会有预期的效果。     

多管脉冲爆震发动机压力反传特性试验与数值研究

为了研究多管脉冲爆震发动机的压力反传特性,采用数值模拟和试验相结合的方法对四管爆震室的压力反传特性进行研究,测量了四管爆震室同时点火和分时点火这两种工作模式下的压力反传规律,利用数值模拟对四管爆震室共用进气道进行研究,分析了共用进气道长度以及在共用进气道内加装分流板对压力反传的影响。试验结果表明,四管爆震室同时工作时,共用进气道产生一道很强的压力扰动波,其峰值压力接近0.12MPa;四管爆震室分时工作时,共用进气道在一个循环内出现四次压力扰动,但扰动波的峰值压力较小。数值模拟的结果表明,在两种工作模式下,爆震室产生的反传压力使发动机入口产生高速倒流,四管分时工作时倒流的速度较小。随着共用进气道的长度增大,反传压力的峰值降低,但发动机入口处仍然存在倒流现象,倒流的速度随着共用进气道的长度增大而减小。共用进气道内加装分流板对反传压力的峰值并没有削弱作用。     

Interaction of single-pulse laser energy with bow shock in hypersonic flow

Pressure sensing and schlieren imaging with high resolution and sensitivity are applied to the study of the interaction of single-pulse laser energy with bow shock at Mach 5. An Nd:YAG laser operated at 1.06 lm, 100 mJ pulse energy is used to break down the hypersonic flow in a shock tunnel. Three-dimensional Navier–Stokes equations are solved with an upwind scheme to simulate the interaction. The pressure at the stagnation point on the blunt body is measured and calculated to examine the pressure variation during the interaction. Schlieren imaging is used in conjunction with the calculated density gradients to examine the process of the interaction. The results show that the experimental pressure at the stagnation point on the blunt body and schlieren imaging fit well with the simulation. The pressure at the stagnation point on the blunt body will increase when the transmission shock approaches the blunt body and decrease with the formation of the rarefied wave. Bow shock is deformed during the interaction. Quasi-stationary waves are formed by high rate laser energy deposition to control the bow shock. The pressure and temperature at the stagnation point on the blunt body and the wave drag are reduced to 50%, 75% and 81% respectively according to the simulation. Schlieren imaging has provided important information for the investigation of the mechanism of the interaction.     

Determination of window frequency in the millimeter wave band in the range of 58° north through 45° south over the globe

The radiosonde data available from British Atmospheric Data Centre (BADC) for the latitudinal occupancy of 58° north through 45° south were analyzed to observe the variation of temperature and water vapor density. These two climatological parameters are largely assumed to be the influencing factors in determining the millimeter wave window frequencies over the chosen range of latitudes in between the two successive maxima occurring at 60 and 120 GHz. It is observed that between temperature and water vapor density, the later one is influencing mostly in determining the window frequency. It is also observed that the minima is occurring at 75 GHz through 94 GHz over the globe during the month January–February and 73 GHz through 85 GHz during the month July–August, depending on the latitudinal occupancy. It is observed that the large abundance of water vapor is mainly held responsible for shifting of minima towards the low value of frequencies. Hence, it is becoming most important to look at the climatological parameters in determining the window frequency at the place of choice.     

石墨烯/Fe3O4复合材料的制备及电磁波吸收性能

为扩展石墨烯的应用领域,对磁性功能化石墨烯的电磁波吸收性能进行研究.在氧化石墨与Fe3 O4粒子的悬浮液中添加还原剂水合肼,微波辐照反应制备石墨烯/Fe3 O4复合物.采用X射线衍射、透射电镜等手段对材料的结构和Fe3 O4的分布状态进行了测试表征.采用矢量网络分析仪测定了材料在0.1～18.0 GHz频率范围内的复介...     

入射喷口宽度对环形射流激波聚焦起爆爆震的影响分析

为了研究射流入射喷口宽度对环形激波聚焦爆震起爆的影响,本文以氢气和空气混合物为例,对不同射流入射喷口宽度的环形激波聚焦爆震起爆过程进行了数值模拟,结果表明,当入射温度为一定值时,不同宽度的环形射流入射喷口对应着不同入射压力pin的临界值,当pin大于该临界值时,其形成的激波聚焦才能够形成高温、高压区域,从而起爆爆震波;随着入射喷口宽度的增加,射流的入射强度增大,其对应的临界入射压力随之减小。     

六管气动阀PDE协调工作研究

为了得到六管气动阀脉冲爆震发动机(PDE)的协调工作,在共用进气道条件下,主要采用离子探针技术进行了试验研究,同时对爆震波激波后燃烧波的传播速度进行了定量测量,并用压力传感器进行了试验验证.研究结果表明:在单管频率f＝30Hz(总频率f＝90Hz)时,六管PDE能够协调、稳定的工作;采用局部蒸发器改善燃油蒸发后,爆震管...     

水下超声速燃气射流气泡的生长及压力波传播特性实验研究

为获取燃气射流对上游水域的影响特性,采用燃气发生器和水下实验系统,研究了水下超声速燃气射流的气泡生长及演变过程,以及气泡压力波在水中的传播特性,并研究了压力波在水介质中的衰减规律。研究表明,燃气泡生长和"破碎"伴生着压力脉动在水介质中传播,气泡压力波的能量在水介质中快速衰减。