基于YOLOv6框架实现典型通信信号调制快速识别方法

随着战场通信侦察对抗系统的快速发展,通信信号体制变得非常复杂,给非合作接收条件下的通信信号检测、调制识别及信号辐射源个体识别带来困难。为了全面掌握信号先验信息,对复杂多样的通信信号体制进行盲检与识别,本文提出基于时频图分析和深度神经网络的多种通信信号自动调制识别方法。首先,利用时频分析将不同典型通信信号转换为时频图像,再将标注后的时频图输入基于深度学习的YOLOv6（目标检测模型）网络中进行特征学习;然后,通过设计YOLOv6更高效的网络结构,使其能够对信号的时频图进行快速识别;最后,将训练后的网络权重对典型通信交叠信号进行测试,对提取的特征向量进行分类识别,完成6种调制方式识别与位置的快速确定,实现在非合作接收条件下的多个典型通信信号调制方式的检测和识别。     

基于DSP的导弹舵机控制系统的研究

应用TMS32 0F2 4 0DSP设计了全数字无刷直流电机的新型导弹舵机伺服驱动系统 ,详细介绍了系统的组成原理、硬件设计及控制策略。试验结果表明 ,此系统具有良好的动态和静态特性。     

TC4激光选区熔化/同轴送粉成形连接的力学性能研究

对TC4选区熔化/同轴送粉成形连接件的拉伸性能和疲劳性能进行研究.通过对比不同线能量密度参数下拉伸试验数据,得到线能量密度对TC4成形连接件拉伸性能的影响规律.通过对比相同应力水平下成形连接件与母材的中值疲劳寿命和疲劳极限,获得成形连接件相对母材疲劳特性的衰减程度.采用当量Kt法对成形连接件的疲劳性能进行表征,得到成形...     

On the time of minimum ionization in the F2 region

Using measurements of the critical frequency of F2 region (f_oF2) the validity of the International Reference Ionosphere model to predict the time of minimum ionization is checked. Data obtained at different ionospheric stations have been considered. The CCIR and URSI options are used to model calculations. For CCIR option the results show that good predictions were obtained for about 40% of the considered cases. For the rest of the considered data, the model predicts the minimum at times earlier than that observed in the measurements. The percentages of good predictions obtained with URSI option are lower than those corresponding to CCIR one.     

定点DSP的开发实践

本文阐述了在定点DSP芯片的开发过程中如何进行数据处理特别是实数处理以及开发过程中要注意的一些问题。     

激光增材制造钛合金构件的化学抛光工艺研究

采用HNO3-HF抛光液对激光选区熔化钛合金制件进行化学抛光,以试样表面粗糙度、减薄及失重变化为指标探究了抛光过程中不同温度和时间对钛合金增材制件抛光效果的影响。通过电化学测量、拉伸试验、残余应力测试等方法对比分析了化学抛光前后钛合金试样的电化学和力学性能。结果表明在温度30℃、反应时间10min下抛光钛合金可以取得较理想的抛光效果,试样表面粗糙度减小、耐腐蚀性能提高。化学抛光后钛合金的强度出现小幅下降,内部原有的残余应力由拉应力转变为压应力。     

2009年7月22日日全食期间电离层参量的变化

利用多个电离层垂测站的数据和IGS-TEC数据资料, 结合日地空间环境指数, 分析了2009年7月22日日全食期间中国地区电离层参量(反射回波最低频率fmin及f0F2和TEC)的变化特征. 结果表明, 日食发生后fmin迅速降低, 日食结束后fmin迅速恢复到正常水平; 在食甚时刻附近, f0F2和TEC出现明显的降低, 显示了明显的光食效应. 日食结束后5~6 h, f0F2和TEC出现不同程度的正扰动, 在驼峰区更明显; 日食结束后9~10 h, f0F2和TEC出现较显著的负扰动. 由于此次日食发生时伴随着中等强度的磁暴和低纬电场穿透等空间天气事件, 给此次日食电离层效应的深入分析带来很大困难.      

Seasonal and solar cycle dependence of F3-layer near the southern crest of the equatorial ionospheric anomaly

The occurrence of an additional F3-layer has been reported at Brazilian, Indian and Asian sectors by several investigators. In this paper, we report for the first time the seasonal variations of F3-layer carried out near the southern crest of the equatorial ionospheric anomaly (EIA) at São José dos Campos (23.2°S, 45.0°W; dip latitude 17.6°S – Brazil) as a function of solar cycle. The period from September 2000 to August 2001 is used as representative of high solar activity (HSA) and the period from January 2006 to December 2006 as representative of low solar activity (LSA). This investigation shows that during HSA there is a maximum occurrence of F3-layer during summer time and a minimum during winter time. However, during LSA, there is no seasonal variation in the F3-layer occurrence. Also, the frequency of occurrence of the F3-layer during HSA is 11 times more than during LSA.     

VFC在捷联惯导数据采集系统中的应用

介绍一种以压频转换来实现捷联惯性制导系统惯性器件信号采集的方法。在本系统中以TI公司的TMS320C6711 DSP器件为核心,采用VFC型ADC转换器件AD652,利用可编程的定时器/计数器芯片8253对AD652的输出脉冲串进行计数。对系统硬件平台的方案设计和软件设计进行了分析。分析结果表明,本系统充分利用了压频转换芯片抗干扰能力强、应用灵活的优点,满足了导弹捷联惯性制导数据采集系统可靠性高的要求。     

Influence of longitudinal-torsional ultrasonic-assisted vibration on micro-hole drilling Ti-6Al-4V

As Ti-6Al-4V is a typical hard to machine material, especially in micro drilling aviation parts, chip breaking difficulty is of increasing interest to explore its further development. In this study, Longitudinal-Torsional Ultrasonic Assisted Drilling (LTUAD) was employed to machine Ti-6Al-4V, and its feasibility was evaluated by comparing with Conventional Drilling (CD). By combining periodical characteristics and vibration models (the separated or the unseparated ultrasonic elliptical vibration), the influence of ultrasonic frequency on the intersection characteristics of trajectories were analyzed. And the intersection characteristics were divided into four categories: even periodicity, odd periodicity, non-odd and even periodicity and composite periodicity, indicating different capability for chip breaking. By applying the longitudinal-torsional compound vibration horn, the micro-hole drilling experiment was carried out on machining center. The chip morphology, the thrust force, and the burr height were discussed. Experimental results showed that the morphology of chips presented as smaller and more fragmentary ones in LTUAD compared with continuous helical conical ones and fold-shaped ones in CD. Compared with CD, the average values of the thrust force in LTUAD reduced by 1.98% to 24.9%. According to the burr around the hole exit in both LTUAD and CD, the height of the latter was greatly affected by the drilling parameters. And the burr around the exit of the hole were distributed rather evenly with smaller extension in LTUAD. Consequently, the LTUAD employed in micro-hole drilling was effective.