纳米碳酸盐对复合固体推进剂燃烧性能的影响

研究了纳米碳酸盐对丁羟三组元、丁羟四组元、低燃速NEPE推进剂燃烧性能的影响。结果表明:纳米碳酸盐使丁羟三组元推进剂在高压(10～18MPa)和低压(4～10MPa)段的压强指数降低到0.2以下,同时使燃速明显降低;使丁羟四组元推进剂在高压段(10～18MPa)的压强指数降低到0.26左右;使低燃速NEPE推进剂的的压强指数(4～9MPa)从0.77左右降至0.55以下。从研究结果可以看出,添加该纳米碳酸盐是降低复合推进剂压强指数行之有效的途径。     

转静干涉对叶片非定常表面压力的影响

为了研究转静干涉对叶片表面压力的影响,通过数值模拟的方法,计算了一级低速轴流压气机流场,得到了充分收敛的周期性非定常流场解。在此基础上分析了叶片表面压力及气动力的变化规律,并通过改变背压,研究了流量对叶片表面压力和气动力的影响。最后在低速轴流压气机实验器上进行了实验验证,结果表明计算和实验的结果吻合得较好。     

椭圆形扰流柱冷却通道流动与换热数值研究

采用数值计算方法对涡轮叶片椭圆形扰流柱排冷却通道的流动和换热进行了研究,得到了排列间距、迎角、椭圆长短轴之比等因素对冷却通道流动和换热性能的影响.在相同截面积和排列方式条件下,椭圆形扰流柱迎角为0°时,分析结果表明,椭圆形扰流柱冷却通道压力损失系数约为圆形扰流柱通道的51.7%,平均努塞尔数约为圆形扰流柱通道的83.75%;长短轴比为5/1.8时,压力损失系数仅为圆形扰流柱通道的(长短轴比等于3/3)28.1%～35.5%,平均努塞尔数为圆形扰流柱通道的71.1%～75.06%.      

两级超声速引射器流动机理研究

超声速引射器在航天发动机、化学激光器等的地面试验所需压力恢复系统中有着重要的应用,采用超-超引射方式是优化压力恢复系统的性能和实现设备小型化的途径之一。为探索适用于超-超引射器的设计准则,对一种两级超声速引射器的超-超引射流动现象开展了研究,试验发现该构型引射器在特定压力匹配范围内即可实现一、二级主流间的超-超引射又可以实现主流对二次流的超-超引射,结合数值仿真对流场结构和参数的分析表明超-超引射的形成机制可归结为压力匹配问题,通过提高来流总压与混合室匹配静压的压比可建立超-超引射;混合室匹配静压由引射气流主导;提高二次流总压或降低主流压力均可提高二次流马赫数,该规律对建立超-超引射、提高引射效率有指导意义。      

涡脱位置及温度对涡声效应压力振荡影响

为探索涡-声效应对固体火箭发动机中压力振荡特性的影响,基于VKI (Von Karman Institute for Fluid Dynamics)发动机,通过改变挡板位置与燃气温度,对旋涡脱落引起的压力振荡进行了大涡模拟数值研究.耦合分析表明:挡板位于速度波腹附近,压力振荡最为严重;旋涡能量在输运过程中易于被湍流耗散,靠近喷管的二阶速度波腹处旋涡脱落压力振幅明显高于其它位置.解耦分析表明:温度对旋涡脱落频率影响不大,当旋涡脱落频率与声振频率分离后,压力振幅显著下降.     

Dynamics modeling and pressure control of composites tape winding system based on LQSMC

Pressure fluctuations during the composite fiber winding process seriously affect the product's compactness strength, fatigue resistance, stress uniformity, and resin content. The accuracy of pressure control systems is affected by nonlinear disturbances, such as friction, parameter perturbation, and measurement noise. A robust control algorithm based on linear quadratic optimal control and sliding mode control (LQSMC) is proposed to overcome these problems. The method is based on the system state space expression and linear quadratic optimal control. The state space model of the system is improved by using a Kalman filter and control input for state estimation, and a new sliding surface equation is defined. The ameliorated control algorithm exhibits good performance and can effectively suppress sliding mode control (SMC) chattering. Simulation and experimental results show that LQSMC offers high control precision, much stronger anti-interference, and robustness, which can effectively improve the positioning and tracking accuracy of a pressure control system compared with linear quadratic optimal control (LQC). The winding pressure control precision is improved by 45% to 50%. The results show that the porosity of composite fiber tape winding products decreased thanks to our method.     

Thermal stability improvement of sprayable fast-responding pressure-sensitive paint for measurement above 100 °C

The thermal stability of sprayable fast-responding Pressure-Sensitive Paint (fast PSP) was investigated to explore the possibility for application in turbomachinery and hypersonic research with temperature above 100 °C. The first part of the study focused on a widely-used Polymer Ceramic PSP (PC-PSP). The effects of thermal degradation on its key sensing properties, including luminescent intensity, pressure sensitivity and response time, were examined for a temperature range from 60 to 100 °C. Severe degradation in intensity and pressure sensitivity was found as temperature reached 70 °C or higher, which would cause failure of PSP application in these conditions. Subsequently, a fast-responding Mesoporous-Particle PSP (MP-PSP) was developed which did not show degradation effects until 140 °C. The greatly improved thermal stability of MP-PSP was attributed to: selection of polymer with higher glass transition temperature (polystyrene) to delay the saturation effect of oxygen quenching as temperature increased; porous and hollow structure of particles for luminophore deposition that minimizes polymer–luminophore interaction. This new paint formulation has significantly raised the upper temperature limit of fast PSP and offers more opportunities for applications in harsh environment.     

Pressure distribution guided supercritical wing optimization

Pressure distribution is important information for engineers during an aerodynamic design process. Pressure Distribution Oriented (PDO) optimization design has been proposed to introduce pressure distribution manipulation into traditional performance dominated optimization. In previous PDO approaches, constraints or manual manipulation have been used to obtain a desirable pressure distribution. In the present paper, a new Pressure Distribution Guided (PDG) method is developed to enable better pressure distribution manipulation while maintaining optimization efficiency. Based on the RBF-Assisted Differential Evolution (RADE) algorithm, a surrogate model is built for target pressure distribution features. By introducing individuals suggested by sub-optimization on the surrogate model into the population, the direction of optimal searching can be guided. Pressure distribution expectation and aerodynamic performance improvement can be achieved at the same time. The improvements of the PDG method are illustrated by comparing its design results and efficiency on airfoil optimization test cases with those obtained using other methods. Then the PDG method is applied on a dual-aisle airplane’s inner-board wing design. A total drag reduction of 8 drag counts is achieved.     

Effect of an end plate on surface pressure distributions of two swept wings

A series of wind tunnel tests was conducted to examine how an end plate affects the pressure distributions of two wings with leading edge(LE) sweep angles of 23° and 40°. All the experiments were carried out at a midchord Reynolds number of 8×10~5, covering an angle of attack(AOA) range from -2° to 14°. Static pressure distribution measurements were acquired over the upper surfaces of the wings along three chordwise rows and one spanwise direction at the wing quarter-chord line. The results of the tests confirm that at a particular AOA, increasing the sweep angle causes a noticeable decrease in the upper-surface suction pressure. Furthermore, as the sweep angle increases, the development of a laminar separation bubble near the LEs of the wings takes place at higher AOAs. On the other hand, spanwise pressure measurements show that increasing the wing sweep angle results in forming a stronger vortex on the quarter-chord line which has lower sensitivity to AOA variation and remains substantially attached to the wing surface for higher AOAs than that can be achieved in the case of a lower sweep angle. In addition, data obtained indicate that installing an end plate further reinforces the spanwise flow over the wing surface, thus affecting the pressure distribution.     

气流展纤工艺中不同压差和送丝速度对碳纤维展宽的影响

为探究气流展纤工艺中不同出口压差和送丝速度对碳纤维丝束展宽效果的影响,依据Venturi原理,搭建气流展纤试验平台,并记录大丝束碳纤维展宽过程,计算不同工艺参数下碳纤维丝束在不同阶段的展宽率和展宽均匀程度。研究结果表明：通过搭建的气流展纤试验台,能获得展宽率高于400%,展宽均匀程度在90%以上的碳纤维丝束,得到的碳纤维丝束的展宽率与出口压差呈正相关,与送丝速度呈负相关;碳纤维丝束的展宽均匀程度与出口压差呈负相关,与送丝速度呈正相关。