基于压力信号器控制的贮箱地面增压技术应用分析

对基于压力信号器控制的贮箱地面增压技术及其在发射场的实际应用情况进行了介绍分析。常温贮箱射前地面增压时间较为宽裕，一般采用单气路单压力信号器控制增压；低温贮箱射前地面增压时间较短，要求较快的增压速率，一般采用双气路双压力信号器控制增压。贮箱射前地面增压存在压力后效，影响压力后效大小的主要因素包括：增压充气流量qm、增压电磁阀动作响应时间Δt、增压电磁阀后供气管路气体容积Vg。发射场实际应用过程中，通过调整供气管路上节流孔板大小控制增压充气流量，使贮箱增压压力后效满足要求。针对压力信号器失效故障模式，通过设置紧急放气电磁阀和冗余设计,实现紧急放气和冗余备保增压，可以确保贮箱射前增压工作正常。     

Experimental investigation of characteristics of instability evolution in a centrifugal compressor

The stable range of operation for the centrifugal compressor significantly influences the dynamic, economic, and environment-friendly characteristics of power systems. A deep understanding of the characteristics of instability evolution is necessary to improve the compressor stability. A centrifugal compressor equipped with a vaneless diffuser is experimentally investigated using highresponse static-pressure measurements. The results obtained indicate that three typical rotationalspeed ranges ex...     

基于EFPI-FBG结构的光纤复合传感器研究

研究了一种基于非本征型Fabry-Perot干涉仪(EFPI)和光纤Bragg光栅(FBG)串联结构构成的EFPI-FBG光纤复合传感器,用于实现对压力和温度信号的同步测量。传感器选用熔融石英作为压力敏感材料,利用飞秒激光焊接技术实现传感器探头结构的封装。对传感器的工作原理进行了分析,制作并封装传感器工程样机,搭建测试系统,对传感器的性能进行了灵敏度及交叉敏感性分析。结果表明,该传感器在0.8 MPa范围内的灵敏度约为-0.729μm/MPa,在50℃~200℃范围的温度灵敏度为0.009 nm/℃,传感器压力测量最大允许误差为±4.12%FS。该EFPI-FBG复合传感器有望应用于压力—温度双参数测量需求的技术领域。     

旋转爆轰波与涡轮平面叶栅相互作用数值模拟

由于旋转爆轰燃烧室具有自增压特性，可提高热力循环效率，因此将旋转爆轰燃烧室应用于燃气轮机可进一步提高系统的性能。基于非稳态雷诺时均Navier-Stokes方法，采用剪切应力输运k-ω湍流模型，建立旋转爆轰燃烧室与涡轮平面叶栅耦合计算模型，研究旋转爆轰燃烧室内的复杂波系与涡轮叶片的相互作用，分析涡轮叶栅对高频爆轰压力振荡的抑制作用。结果表明：旋转爆轰燃烧室内的燃气在涡轮叶栅内加速，并且在斜激波后的局部区域马赫数的增加更为明显。斜激波与涡轮静转子叶片的前缘、压力面、吸力面以及尾缘相互作用，由于旋转爆轰波不同的传播方向，使得斜激波与静子叶片呈相互垂直或平行，进而形成两种不同的波系结构。涡轮叶栅对高频压力振荡存在明显的抑制作用，涡轮叶栅上下游高频压力振荡幅值的衰减率达到80%以上。研究结果展示了旋转爆轰波作用下涡轮叶栅内复杂波系结构特征，并对基于爆轰燃烧推进技术的应用提供了一定的理论基础。     

Experimental study on dynamic behavior of mechanically pumped two-phase loop with a novel accumulator in simulated space environment

Mechanically pumped two-phase loop (MPTL) which is a prominent two-phase heat transfer technology presents a promising prospect in thermal control for space payload. However, transient behavior of MPTL caused by phase-change and heat sources load-on/off in simulated space environment is rarely reported. In the present study, one MPTL setup was designed and constructed, and experimentally studied. Particularly, a novel two-phase thermally-controlled accumulator integrated with passive cooling measure and three capillary structures was designed as the temperature-control device. Dynamic behavior of the start-up, temperature control, and temperature adjustment were monitored; meanwhile, thermodynamic behavior within the proposed accumulator, the operating behavior as well as the heat and mass transfer behavior between the main loop and the accumulator were revealed. The results show that the fluid management function of the capillary structures for the novel accumulator is verified. The working point of the MPTL system can be adjusted by changing the temperature control point of the accumulator and it is little influenced by external heat flux and heat sources on/off. Pressure-drop oscillations which are manifested as fluctuations of temperature and pressure can be observed after phase changing due to the compressible volume within the accumulator and the negative-slope portion of the internal pressure.     

Pressure distribution feature-oriented sampling for statistical analysis of supercritical airfoil aerodynamics

In the field of supercritical wing design, various principles and rules have been summarized through theoretical and experimental analyses. Compared with black-box relationships between geometry parameters and performances, quantitative physical laws about pressure distributions and performances are clearer and more beneficial to designers. With the advancement of computational fluid dynamics and computational intelligence, discovering new rules through statistical analysis on computers has beco...     

Investigation of pressure wave behaviors in the rotational speed effects on a pressure-exchange wave rotor

A wave rotor is suitable for compact and efficient pressure-exchange between gas flows.This work measured the circumferential pressure distribution of the rotor/stator interfaces and utilized a CFD method to simulate the unsteady pressure waves. The experimental and CFD results showed some slopes in the circumferential pressure distributions, and the slopes indicated the traces of specific unsteady pressure waves. Such traces varied regularly if the rotational speed varied within a range from-11...