激波绕射触发爆震波的试验研究

在单爆震试验平台上对激波绕射触发爆震波的特性进行了试验研究.针对不同的激波反射器结构尺寸,测量了爆震管内气体压力变化历程及火焰传播速度,获得了不同工况下激波绕射触发爆震波的特性.结果表明:激波反射器对爆震波的形成有促进作用,并取决于反射器中的反射锥及反射孔板的结构与尺寸;在反射锥堵塞比一定的情况下,存在最佳反射锥锥角使得爆震波的形成距离最小;而反射锥与反射孔板的间距增大,爆震波形成距离增大,一旦形成稳定的爆震波后,反射器对爆震波压力的影响不大.      

The Full Flowpath Analysis of a Hypersonic Vehicle

对一种类X43-A吸气式高超飞行器全流道开展了M7一级的三维数值仿真研究,深入探索了进气道处于起动状态和不起动状态时全流道的冷流流场结构和和气动力特性,且部分结果与实验数据进行了对比。研究结果表明:(1)前体横截面上存在显著的展向压强梯度,使得经过预压缩的气流偏离了进气道进口,但同时也减少了进入内通道的边界层气流,提高了进口流场的品质;(2)后体喷流股的膨胀过程受到了周围外流的显著干扰,因而沿流动方向其截面形状不断发生变化,如在喷口附近为近似矩形,而在后体末端附近则演化为近似三角形;(3)当进气道处于不起动状态时,其全流道流动结构发生了显著变化,进气道的外部压缩波系往复振荡,尾喷管出口的喷流股也在不停的膨胀和收缩,具有极强的非定常特征;(4)当进气道处于不起动状态时,全机的气动力特性呈周期性变化,升阻比的变化幅度较大,在最大、最小值分别可达起动状态的2倍和1/4倍。另外,升力、阻力系数的变化曲线之间存在一定的相位差;(5)与实验结果的对照表明,所采用的数值仿真方法具有较高的精度。     

Ion dynamics associated with Alfven wave in the near-Earth magnetotail: Two-dimensional global hybrid simulation

Ion dynamics in the near-Earth magnetotail region is examined during periods of fast Earthward flow with a two-dimensional (2-D) global-scale hybrid simulation. The simulation shows that shear Alfven waves are generated at x ∼ −10R_E, where the strong earthward flow is arrested by the dipole field, and propagate along field lines from the equator to both southern and northern polar ionosphere. Non-gyrotropic ion velocity distributions occur where the large-amplitude Alfven waves are dominant. The simulation indicates that the Alfven waves are generated by interaction of the fast earthward flow with the stationary near-Earth plasma. Beam ions are found to be pitch-angle scattered and trapped in the wave field, leading to the non-gyrotropic ion distributions in the high-latitude plasma sheet boundary. In addition, significant particle heating and acceleration are found to occur behind the dipolarization front due to the effect of wave turbulence.     

Improvement in the GERB short wave flux estimations over snow covered surfaces

Because space-borne radiometers do not measure the Earth’s outgoing fluxes directly, angular distribution models (ADMs) are required to relate actual radiance measurement to flux at given solar angle, satellite-viewing geometries, surface, and atmospheric conditions. The conversion of one footprint broad-band radiance into the corresponding flux requires therefore one to first characterize each footprint in terms of surface type and cloud cover properties to properly select the adequate ADM.

A snow (and sea-ice) retrieval technique based on spectral measurements from the Spinning Enhanced Visible and Infrared Imager (SEVIRI) on board Meteosat 8 is presented. It has been developed to improve the scene identification and thus the ADM selection in the near-real time processing of the Geostationary Earth Radiation Budget (GERB) data at the Royal Meteorological Institute of Belgium. The improvement in the GERB short wave flux estimations over snow covered scene types resulting from angular conversion using dedicated snow ADMs (e.g., empirical snow ADMs and/or pre-computed theoretical snow ADM) instead of empirical snow-free ADMs is discussed.     

RPC-MIP: the Mutual Impedance Probe of the Rosetta Plasma Consortium

The main objective of the Mutual Impedance Probe (MIP), part of the Rosetta Plasma Consortium (RPC), is to measure the electron density and temperature of Comet 67P/Churyumov-Gerasimenko’s coma, in particular inside the contact surface. Furthermore, MIP will determine the bulk velocity of the ionised outflowing atmosphere, define the spectral distribution of natural plasma waves, and monitor dust and gas activities around the nucleus. The MIP instrumentation consists of an electronics board for signal processing in the 7 kHz to 3.5 MHz range and a sensor unit of two receiving and two transmitting electrodes mounted on a 1-m long bar. In addition, the Langmuir probe of the RPC/LAP instrument that is at about 4 m from the MIP sensor can be used as a transmitter (in place of the MIP ones) and MIP as a receiver in order to have access to the density and temperature of plasmas at higher Debye lengths than those for which the MIP is originally designed.     

一种叉齿式微硅加速度计的设计与分析

本文介绍了一种适合军民两用市场的、中低精度的叉齿式微硅加速度计的设计和仿真 ,其敏感轴平行于检测质量平面 ,微结构梁采用了折叠梁结构。对这种加速度计的结构参数进行了理论设计和优化选择 ,利用Ansys结构分析软件重点研究了折叠梁结构参数对加速度计固有谐振频率和力学特性的影响。最后给出了一个符合仪表性能要求的微加速度计 ,其中心摆片大小为 1.6 mm× 1.0 mm ,量程为 2 5 g,分辨率为 0 .5× 10 - 3g。     

分布式电能计量与计费系统中通信信道特性与实现方案的研究

本文介绍了分布式电能计量与计费系统中低压电力线作为载波通信信道时的信道特性，给出了实验数据和特性曲线，并选择了通信的基本方案。     

基于重复控制技术的航空静止变流器

针对航空静止变流器输出电压波形畸变的问题,提出了采用重复控制技术解决方案.重复控制的基本思想是控制理论中的内模原理,逐周期地消除控制误差.分析了重复控制补偿器的数学表达式;证明了重复控制系统的稳定性和收敛性;给出了控制器各环节参数的频域设计方法;并根据一台采用单极性倍频正弦脉宽调制(SPWM)的6kVA/50Hz/200V航空静止变流器的实际参数进行仿真验证.仿真结果表明了控制模型和参数设计方法的正确性,同时也验证了重复控制对解决逆变电源受基波整数倍周期性信号干扰或带非线性负载所造成的输出电压波形畸变是行之有效的.      

核辐射对透波材料介电性能影响

用加速老化试验的方法,在有氧存在的条件下,研究了TDE-85环氧树脂/E玻璃纤维体系、4501A双马来酰亚胺树脂/D3W玻璃纤维体系2种透波材料介电性能受核辐射影响的规律.用60Co辐射源在辐射量为50~800kGy范围内对样件进行辐射,用波导法测试样件的介电常数和介电损耗,测试频率为10GHz.结果发现2种体系透波材料介电性能受核辐射的影响较小,且后者比前者具有更好的抗辐射稳定性.同时利用IR,TGA等手段研究了材料介电性能变化的原因.      

桨根柔性无铰旋翼桨叶气弹稳定性建模分析

建立了任意剖面无铰旋翼桨叶气弹稳定性分析模型,分析了复合材料柔性梁对无铰旋翼桨叶气弹稳定性的影响.将旋翼桨叶简化为二维截面特性线性分析和一维梁非线性分析,二维特性分析考虑了面内和面外翘曲,一维分析采用中等变形梁理论,考虑了剪切变形和与扭转相关的翘曲.采用准定常气动力,运用有限元理论,得出了无铰旋翼桨叶稳定性分析的有限元列式.研究了柔性梁不同铺层方式对气动弹性稳定性的影响.算例表明复合材料柔性梁铺层角对旋翼桨叶气动弹性稳定性影响明显,充分地利用这些影响变化规律,能够设计出更为先进的复合材料悬翼桨叶.