Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

某型飞机数字防滑刹车控制盒可靠性分析与设计

对某型飞机数字防滑刹车控制盒的可靠性进行了分析,利用工程加权法对控制盒进行了可靠性分配,并通过元器件可靠性预计法对控制盒的可靠性进行预计.对比及验证表明,控制盒可靠性设计合理,满足主机及系统要求.     

Atmospheric reentry hemisphere prediction for prograde orbits using logical disjunction

A unique logic-based algorithm for atmospheric reentry hemisphere prediction is presented for spacecraft in low-eccentricity, prograde low Earth orbits at altitudes of 300 km and lower. Using two-line element (TLE) data for initial orbit conditions, coupled with coarse estimates for spacecraft aerodynamic characteristics, the algorithm relies on logical disjunction operations based on a dual analysis of histogram and two-weighted Gaussian probability density function (PDF) fits of predicted reentry latitude data. The algorithm requires the execution of a series of parametric simulations to determine the reentry hemisphere for variations in spacecraft aerodynamic coefficients and drag reference area. When implemented, the algorithm yields accurate hemisphere predictions on average 15 days from reentry as demonstrated by historical reentry cases from 1979 to 2018. All reentry cases were selected to demonstrate the algorithm’s ability to deliver accurate reentry hemisphere predictions for spacecraft with varying physical size and mass, and reentering during different periods of solar cycle activity.     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

激光器性能综合测试设备研制

介绍了激光器的主要性能指标,根据实际需要进行了激光性能测试设备的研究,提出了一种周全的激光性能测试设备研制方案,对该设备的结构设计、光路设计、以及测试方法作了详尽论述。设备中利用两对相互垂直的P分光镜和S分光镜以补偿偏振光在45°面上透反射率不同而造成的测量误差,进一步保证了激光能量测试的准确性。误差分析结果表明该设备满足实际应用中对激光器性能的测试要求。     

聚氨酯涂层体系特性与性能分析研究

为了获得不同聚氨酯涂层的防护特性试验数据,采用漆层参数指标特性分析和样件耐受环境试验的方法,对装备表面起防护作用的聚氨酯防护涂层的综合特性进行分析和研究。研究结果可作为工艺研究和指导生产的参考依据。     

用于分级燃烧的高性能燃油分配器的改进设计与仿真

为了提高燃料使用效率、降低污染物排放,在已有分级燃烧燃油分配器基础上,针对航空发动机双环腔燃烧室改进设计了1种高性能燃油分配器。简述了分级燃烧燃油分配器的工作原理,建立了其AMESim模型。根据设计要求,通过仿真验证了燃油分配器的稳定性、分配比与输入信号的稳态关系,计算了燃油分配器输出与燃油分配计划表之间的误差,分析了燃油分配器的动态特性以及对外部参数变化的鲁棒性,并且针对该分配器的非线性特性提出了解决办法。仿真结果表明：与文献[4]所设计的燃油分配器相比,改进设计的燃油分配器鲁棒性更好,稳态和动态性能更优。     

基于雷达航迹的航空器质量估算

为保障基于轨迹运行的顺利实施,必须提高四维航迹预测的精度,而四维航迹的精准预测依赖于航空器质量准确估算。鉴于此,构建并分析了航空器能量模型;基于雷达航迹与航空器基础资料( BADA),提出了新型的航空器质量估算方法与步骤;利用最小二乘算法求解了航空器质量的估计值;分别基于预测航迹、雷达轨迹与QAR数据,采用相对误差作为评价指标,实施验证与分析。验证结果表明,提出的方法可将航空器质量估算误差控制在5%以内,从而能够有效地提高航迹预测精度。     

直刃尖刀形状对超声辅助切削系统振动性能的影响

基于超声振动设计理论并结合超声振动变幅杆,设计了一种用于弱刚度材料超声辅助切割的直刃尖刀.建立了直刃尖刀和超声振动系统一体的有限元模型,系统分析了直刃尖刀刀体长度、厚度参数对超声振动系统谐振频率、振幅放大倍数和刀具纵向振幅的影响,探讨了刀具横向和侧向振幅沿刀具轴线方向的分布规律.针对特定的超声振动系统,确定了综合性能最优的刀具参数.研制了具有不同形状参数的去刃模拟刀具,并安装于同一超声振动系统进行测试,对仿真分析结论进行验证,理论分析与试验结果相一致.根据理论分析确定的最佳参数研制了直刃尖刀并测试了其振动性能.研究结论对超声辅助切削加工的直刃刀尖的研制提供了理论指导.