Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

无人机系统的安全性与危险源分析

无人机系统的战术性能及优势将使其在未来高技术战争和民用航空中发挥越来越重要的作用。然 而,由于有人机与无人机飞行事故的特点不同,使得有人机的安全性分析与管理措施不完全适用于无人机系 统。首先,对无人机系统的飞行事故进行统计分析,得出无人机系统事故的特点;然后,合理借鉴有人机的安全 性分析,定义无人机系统的安全性,提出无人机系统事故的严酷度等级划分及相应的危险可接受度;最后,从设 计、机组训练及使用操作三方面进行危险源分析。本文提出的无人机系统不安全事件发生可能性等级划分和 危险源定性分析,可为后续无人机安全管理框架的构建奠定基础。     

基于过渡工作过程的航空发动机气路分析方法

为对发动机机动性能的退化程度进行估计,开展了基于过渡工作过程的气路分析研究。针对气路传感器数目较少的情况,采用序列工作点方法对大量的健康参数进行分析,在增加可用信息量的同时,降低了由多工作点方法的平均效应引入的参数估计系统误差。为解决发动机大偏差性能退化健康参数估计中的计算收敛性问题,提出了间接递归牛顿-拉夫逊法强化非支配分类差分进化算法。针对某型双轴分排涡扇发动机的气路分析结果表明：采用本文所提出的方法能够在气路传感器数目有限的条件下,利用发动机过渡态数据实现对大偏差范围内大量健康参数的高效、准确估计。     

基于飞行签派员的航空公司运行效率提升研究

航空公司运行控制中心是航空公司的核心,而飞行签派员又是运行控制中心的核心,运行控制中心的 效率直接影响到航空公司的运行安全与效益。根据航空公司飞行签派员的特点和管理现状,对效率量化和效 率评估进行分析研究,采用改进层次分析法(AHP)和物元可拓模型相结合的方法,建立适合我国航空公司飞 行签派员运行效率评估模型;针对评价指标在实际情况下更具有针对性和可操作性,提出4项准则和16项指 标组成的基于签派员航空公司运行效率评价指标体系,并进行算例分析。结果表明:所构建的评价指标体系合 理有效,能够真实反映出航空公司的运行效率与飞行签派员、运控设备、AOC组织结构与工作环境和航空公司 管理规定有着密切联系,为公司运行效率的提升提出理论依据。     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。     

雷达信号时差频差测量定位工程实现技术研究

针对星载时差频差无源定位系统对地海面雷达信号定位工程实现需要考虑的实际问题,对雷达信号时差频差测量关键技术进行研究.首先研究了雷达信号时差频差测量方法,然后研究了双星时差频差模糊条件并提出解模糊方法,最后,研究了长时间积累对到达频差的影响,给出随时间变化频差补偿方法.     

基于滚动信息反馈的偏置动量卫星滚动/偏航回路姿态控制器设计

以偏置动量卫星为背景,针对滚动/偏航回路的姿态控制,采用频率分离法分析设计了基于滚动信息反馈的控制器,并给出控制参数的合理选取范围。卫星俯仰回路采用常用的偏置动量轮控制,其滚动/偏航轴上各安装一个反作用飞轮以完成姿态控制。同时,卫星三轴配置磁力矩器以实现动量轮/反作用飞轮的角动量卸载。最后进行了数学仿真,结果表明,卫星滚动/偏航轴的姿态指向控制的精度和稳定度分别达到0.05°和0.001(°)/s,验证了所设计的控制规律的可行性以及控制参数分析的合理性,具有一定的理论意义和工程应用价值。     

编队卫星的状态测量方法综述及可行的高精度星间基线测量方案研究

基线高精度测量是编队卫星应用需要解决的关键技术之一。针对这个问题,文章从3个方面进行了阐述。首先,综述目前国内外常用的编队卫星状态测量手段,然后在前面分析的基础上,结合编队卫星基线的表示方法和卫星编队飞行的特点,提出了2种可行的基线激光测量方案,并对它们各自的测量精度进行了简单地分析。从分析的结果来看,这2种方法均能实现高精度的基线测量。