全文获取类型
收费全文 | 1242篇 |
免费 | 248篇 |
国内免费 | 116篇 |
专业分类
航空 | 678篇 |
航天技术 | 491篇 |
综合类 | 96篇 |
航天 | 341篇 |
出版年
2024年 | 11篇 |
2023年 | 28篇 |
2022年 | 47篇 |
2021年 | 41篇 |
2020年 | 60篇 |
2019年 | 48篇 |
2018年 | 71篇 |
2017年 | 41篇 |
2016年 | 53篇 |
2015年 | 79篇 |
2014年 | 63篇 |
2013年 | 73篇 |
2012年 | 96篇 |
2011年 | 115篇 |
2010年 | 89篇 |
2009年 | 79篇 |
2008年 | 62篇 |
2007年 | 63篇 |
2006年 | 58篇 |
2005年 | 64篇 |
2004年 | 48篇 |
2003年 | 42篇 |
2002年 | 33篇 |
2001年 | 37篇 |
2000年 | 21篇 |
1999年 | 27篇 |
1998年 | 33篇 |
1997年 | 13篇 |
1996年 | 20篇 |
1995年 | 17篇 |
1994年 | 13篇 |
1993年 | 11篇 |
1992年 | 11篇 |
1991年 | 14篇 |
1990年 | 13篇 |
1989年 | 9篇 |
1988年 | 1篇 |
1987年 | 1篇 |
1984年 | 1篇 |
排序方式: 共有1606条查询结果,搜索用时 15 毫秒
991.
In order to implement 3D scanning of those complicated parts such as blades in the aviation field,a non-contact optical measuring system is established in the paper,which integrates a laser displacement sensor,a probe head,the frame of a coordinate measuring machine (CMM),etc.As the output of the laser sensor directly obtained possesses the 1D length of the laser beam,it needs to determine the unit direction vector of the laser beam denoted as (l,m,n) by calibration so as to convert the 1D values into 3D coordinates of target points.Therefore,an extrinsic calibration method based on a standard sphere is proposed to accomplish this task in the paper.During the calibration procedure,the laser sensor moves along with the motion of the CMM and gathers the required data on the spherical surface.Then,both the output of the laser sensor and the grating readings of the CMM are substituted into the constraint equation of the spherical surface,in which an over-determined nonlinear equation group containing unknown parameters is established.For the purpose of solving the equation group,a method based on non-linear least squares optimization is put forward.Finally,the system after calibration is utilized to measure the diameter of a metallic sphere 10 times from different orientations to verify the calibration accuracy.In the experiment,the errors between the measured results and the true values are all smaller than 0.03 mm,which manifests the validity and practicality of the extrinsic calibration method presented in the paper. 相似文献
992.
993.
T. Ning G. Elgered J.M. Johansson 《Advances in Space Research (includes Cospar's Information Bulletin, Space Research Today)》2011
We have used microwave absorbing material in different geometries around ground-based Global Navigation Satellite System (GNSS) antennas in order to mitigate multipath effects on the estimates of station coordinates and atmospheric water vapour. The influence of a hemispheric radome – of the same type as in the Swedish GPS network SWEPOS – was also investigated. Two GNSS stations at the Onsala Space Observatory were used forming a 12 m baseline. GPS data from October 2008 to November 2009 were analyzed by the GIPSY/OASIS II software using the Precise Point Positioning (PPP) processing strategy for five different elevation cutoff angles from 5° to 25°. We found that the use of the absorbing material decreases the offset in the estimated vertical component of the baseline from ∼27 mm to ∼4 mm when the elevation cutoff angle varies from 5° to 20°. The horizontal components are much less affected. The corresponding offset in the estimates of the atmospheric Integrated Water Vapour (IWV) decreases from ∼1.6 kg/m2 to ∼0.3 kg/m2. Changes less than 5 mm in the offsets in the vertical component of the baseline are seen for all five elevation cutoff angle solutions when the antenna was covered by a hemispheric radome. Using the radome affects the IWV estimates less than 0.4 kg/m2 for all different solutions. IWV comparisons between a Water Vapour Radiometer (WVR) and the GPS data give consistent results. 相似文献
995.
996.
997.
998.
999.
1000.
文章以空间相机应用为目的,在分析第二代红外探测器驱动电压与输出信号之间相关性的基础上,以某型号第二代红外探测器驱动电压供电电路设计为例,采用高稳定基准电压芯片和低噪声低频运算放大器作为核心器件,提出了以负反馈或电压跟随的电路形式稳定驱动电压供电的方案,并对该方案进行了仿真分析与实验验证.测试结果证实该方案可行有效,能满... 相似文献