磁场全张量测量计算方法与误差分析

矢量磁场和磁场全张量数据是多磁源反演的数据基础。针对矢量磁场和磁场全张量的测量问题,文章提出了矩阵式矢量磁场连续扫描方法。对利用矢量磁场计算磁场全张量所用的数据结构进行了研究,应用MATLAB软件对常用的十字形和六面体两种不同数据计算结构进行了仿真分析,结果表明,两种计算结构的误差相近且均不大于10%;并分析了基线距离对磁场全张量计算的影响,结果表明,磁场全张量计算误差随着基线距离的增加而增加。     

复杂薄壁构件自适应加工工艺几何模型重构

随着制造理念和制造水平的不断提高,大量复合制造工艺背景下的近净成形叶片被应用到现役或在研的航空发动机中。该类叶片是典型的复杂薄壁结构零件,无精确定位基准,且成形一致性差。采用传统叶身定位,加工后的前/后缘、榫齿形状和位置精度均难以保证,从而导致产品一致性差,易超差与合格率低。针对以上问题,提出一种面向自适应加工的复杂薄壁结构零件工艺几何模型重构方法。首先,建立复杂曲面的采样点分布模型,快速获取叶片精确成型区域的位置和形状;其次,提出基于特征曲线相似变形的模型重构算法,精确重构前/后缘非精确成型区域的工艺几何模型;最后,通过精锻叶片自适应加工试验进行验证。试验结果表明：该方法可有效满足以精锻叶片为代表的复杂薄壁构件自适应加工要求。     

Effects of wing flexibility on aerodynamic performance of an aircraft model

The low-speed wind tunnel experiment is carried out on a simplified aircraft model to explore the influence of wing flexibility on the aircraft aerodynamic performance. The investigation involves the measurements of force, membrane deformation and velocity field at Reynolds number of 5.4 × 10⁴–1.1 × 10⁵. In the lift curves, two peaks are observed. The first peak, corresponding to the stall, is sensitive to the wing flexibility much more than the second peak, which nearly keeps constant. For the optimal case, in comparison with the rigid wing model, the delayed stall of nearly 5° is achieved, and the relative lift increment is about 90%. It is revealed that the lift enhanced region corresponds to the larger deformation and stronger vibration, which leads to stronger flow mixing near the flexible wing surface. Thereby, the leading-edge separation is suppressed, and the aerodynamic performance is improved significantly. Furthermore, the effects of sweep angle and Reynolds number on the aerodynamic characteristics of flexible wing are also presented.     

An error analysis and optimization method for combined measurement with binocular vision

The accurate measurement of surfaces of large aviation components is vital for the assessment of manufacturing and assembly quality of such components. To satisfy the measurement requirement of large-size components, most current researches pay more attention to combined measurement methods utilizing different measuring instruments, but the related researches on error analysis and optimization methods are not taken enough attention. This paper proposes a combined laser-assisted measurement method with feature enhancement techniques, and it also develops an error propagation model of the main factors affecting the overall measurement error in detail. Firstly, the surface of a large-size component is measured by the measurement system at multiple stations. Secondly, a control point coordinate system is established as a bridge to unify all local measurement data into the global coordinate system. To improve the overall measurement accuracy, the pixel extraction error as a key factor causing the overall measurement error is analyzed in detail. Next, the error propagation model is established, and some optimization strategies of layout for minimizing measurement error and transformation error are researched. Finally, experiments are carried out to verify the effectiveness of the proposed method. The results show that the measurement error of the proposed method reaches 0.073% and 0.14% with a 1D standard ruler and a flat plate, respectively.     

一种跟随式大磁矩磁力矩器高反电势抑制技术

摘要： 提出一种可以实现大磁矩磁力矩器磁棒电流续流时间自动调节的控制方法,该方法既可以抑制大磁矩磁力矩器高反电势的产生,又无需增加功率器件为磁棒电流提供续流回路,大幅减小控制线路的体积及热设计难度,同时可以满足输出磁矩在小幅值内频繁变换方向的使用要求.     

基于递推更新卡尔曼滤波的磁偶极子目标跟踪

针对磁性目标跟踪问题,以磁偶极子等效场源模型为基础,建立磁性目标跟踪的离散状态空间模型,将磁偶极子目标实时跟踪问题转化为状态空间模型的滤波估值问题。针对磁性目标初始条件难以获得且现有卡尔曼类滤波算法在大初始误差条件下容易出现发散的问题,提出一种递推观测更新的卡尔曼滤波算法,将现有的一步观测更新描述为递推更新过程,等效降低大初始误差带来的大非线性误差。仿真与实测数据测试结果表明,本文算法具有良好的精度和收敛性,能够有效抑制磁偶极子跟踪中由于大初始误差导致的滤波发散,适于实际应用。     

火焰辐射光场成像光线采样特性

为了研究全光相机对火焰等半透明介质的光场采样并优化全光相机的参数,基于近轴光学,建立了全光相机的逆向光线追迹模型。在此基础上,针对弥散介质沿采集方向的半透明特性,提出了像素采样锥形角以及物方采样角度等评价光线角度采样的性能指标,据此分析了全光相机像素和微透镜的位置对光场采样特性的影响,以及全光相机光学参数变化对光线方向采样性能的影响。结果表明:采集火焰辐射光场时,较小的微透镜直径有利于提高光场采样的单方向性,并减小主镜头入瞳直径,而较小的主镜头焦距有利于增大物方采样角度。     

无通风直升机动力舱火灾温度场数值模拟

采用大涡模拟(LES)技术,针对某型直升机动力舱建立了火灾模型,选择油池火灾作为研究对象,并对火灾场景进行了设计.利用数值模拟的方法研究了不同位置火源动力舱的火灾场,分析了火源位置对火灾热释放速率、速度场和温度场的影响.结果表明:无通风条件下,火源位置的改变影响动力舱火灾的蔓延,并且当火源位于动力舱底部距前防火墙1/4处时,火灾强度较大,对舱内部件的破坏较为严重.因此,在防火设计中应重点对该部位火灾区域进行防范.研究结果可为动力舱灭火系统设计提供参考.      

多导线对称分布原子磁分束器和干涉仪设计分析

提出了采用多根对称分布载流导线构成原子分束器的方法,包括三导线和四导线磁导引。阐述了原子分束器的分束机制,用Ansoft Maxwell 2D软件计算给出了部分载流导线移动到不同位置时的磁场分布图。通过分析了导引中心的变化,发现只要通过改变载流导线之间的相对位置就可以来实现从单路到双路导引和三路导引的转换。由此分别设计由3根对称分布载流导线构成的原子双路分束器和4根对称分布载流导线构成三路分束器,然后运用Monte Carlo方法模拟验证其原子分束功能。最后以三线对称分布分束器为基础构成Mach-Zehnder原子磁干涉仪。     

基于角位移的火控系统旋转变压器改进性设计

通过对旋转变压器角位移测量原理分析,提出了基于粗精通道的改进性方案,利用多模块组合设计,研制出一种新型的角位移测量系统和相应的测量算法。试验表明,改进后的组合测量系统最大误差可控制在±0.01°以内,有效地提高了火控系统角位移测量精度。