The characteristics of sharp (small-scale) boundaries of solar wind plasma and magnetic field structures

We investigate properties of large (>20%) and sharp (<10 min) solar wind ion flux changes using INTERBALL-1 and WIND plasma and magnetic field measurements from 1996 to 1999. These ion flux changes are the boundaries of small-scale and middle-scale solar wind structures. We describe the behavior of the solar wind velocity, temperature and interplanetary magnetic field (IMF) during these sudden flux changes. Many of the largest ion flux changes occur during periods when the solar wind velocity is nearly constant, so these are mainly plasma density changes. The IMF magnitude and direction changes at these events can be either large or small. For about 55% of the ion flux changes, the sum of the thermal and magnetic pressure are in balance across the boundary. In many of the other cases, the thermal pressure change is significantly more than the magnetic pressure change. We also attempted to classify the types of discontinuities observed.     

一般硬化材料弹塑性旋转盘的变分解法

首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;再在体积不变条件下用弹性位移场的已知模态和一待定幅值构成弹塑性位移场;最后用势能原理确定该幅值而得到封闭解。     

研究用现场数据估计系统可靠性参数置信区间

研究用元部件现场信息估计系统可靠性参数,如系统可靠度、可靠寿命等区间估计问题。文中提出了一种新的估计方法——替换百分点法,并运用Monte Carlo数字仿真对估计的置信度和精度进行了分析,研究结果表明此方法具有工程应用价值。     

Orientations of LASCO Halo CMEs and their connection to the flux rope structure of interplanetary CMEs

Coronal mass ejections (CMEs) observed near the Sun via LASCO coronographic imaging are the most important solar drivers of geomagnetic storms. ICMEs, their interplanetary, near-Earth counterparts, can be detected in situ, for example, by the Wind and ACE spacecraft. An ICME usually exhibits a complex structure that very often includes a magnetic cloud (MC). They can be commonly modelled as magnetic flux ropes and there is observational evidence to expect that the orientation of a halo CME elongation corresponds to the orientation of the flux rope. In this study, we compare orientations of elongated CME halos and the corresponding MCs, measured by Wind and ACE spacecraft. We characterize the MC structures by using the Grad–Shafranov reconstruction technique and three MC fitting methods to obtain their axis directions. The CME tilt angles and MC fitted axis angles were compared without taking into account handedness of the underlying flux rope field and the polarity of its axial field. We report that for about 64% of CME–MC events, we found a good correspondence between the orientation angles implying that for the majority of interplanetary ejecta their orientations do not change significantly (less than 45 deg rotation) while travelling from the Sun to the near-Earth environment.     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

Geometric calibration of Colour and Stereo Surface Imaging System of ESA’s Trace Gas Orbiter

There are many geometric calibration methods for “standard” cameras. These methods, however, cannot be used for the calibration of telescopes with large focal lengths and complex off-axis optics. Moreover, specialized calibration methods for the telescopes are scarce in literature. We describe the calibration method that we developed for the Colour and Stereo Surface Imaging System (CaSSIS) telescope, on board of the ExoMars Trace Gas Orbiter (TGO). Although our method is described in the context of CaSSIS, with camera-specific experiments, it is general and can be applied to other telescopes. We further encourage re-use of the proposed method by making our calibration code and data available on-line.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

野战环境下大型飞机超低空气动特性分析

针对野战环境下的大型飞机超低空飞行,采用CFD方法对地面存在前向或横向不对称障碍物时地面效应对气动参数的影响进行了数值分析,包括纵向稳定性和侧向摇晃等问题.研究结果表明,野战等非常规飞行条件下,地面不确定障碍物会造成大型飞机稳定性变差,严重时可能出现纵向点头和横侧向摇晃现象,容易导致触地危险.最后,从现代飞行控制理论角度提出了对常规布局大型飞机进行闭环控制的研究思路.     

复合材料构件热压罐成型温度场研究

在热压罐固化工艺的热历程中,复合材料零件表面温度场分布的合理与否将直接决定产品的固化质量.以工字型零件和T型加筋壁板两种复合材料零件为研究对象,使用EC-3×8M和SCH-5.5×21M两种型号热压罐,同时选择炉温偶和零件偶两种控温方式对零件进行固化.通过分析温度场测试结果发现,控温方式、设备加热方式、升降温速率、热电偶的摆放位置、固化压力等因素均对零件的温度场有影响.