Nb/Nb5Si3微叠层材料及其制备技术

Nb/Nb5Si3合金是未来最具潜力的超高温结构材料,实现该材料的结构微叠层化是一种新颖的材料设计思路和制备方法.Nb/Nb5Si3微叠层材料是将Nb和Nb5Si3按一定的层间距及层厚比以ABABAB型交互重叠结构形成的多层材料,其几种典型的制备技术包括热压、等离子喷涂、磁控溅射和电子束物理气相沉积(EB-PVD).其中EB-PVD是一种最适合工程应用的Nb/Nb5Si3微叠层材料制备方法,结构和功能复合、纳米化叠层、高韧化工艺是EB-PVD技术制备Nb/Nb5Si3微叠层材料的发展方向.     

原位自生TiB2/Al复合材料车削参数多目标优化方法

原位自生TiB2/Al复合材料具有密度小、比强度高、高耐磨等特点,在航空航天领域具有广泛的应用前景.主要针对TiB2/Al复合材料车削参数对表面粗糙度的影响进行探索性研究.首先,以车削速度、进给速度、车削深度为对象,基于单因素试验研究了车削参数控制域.进一步在控制域内设计正交试验,并基于试验结果研究了表面粗糙度与车削参数的映射关系,推导了材料去除率模型.最后,以表面粗糙度和材料去除率为优化目标,提出并研究了基于GA-Pareto的车削参数多目标优化方法,并通过试验验证了该方法的可行性和有效性.     

涡扇发动机闭环控制系统设计仿真平台

航空发动机闭环控制系统的设计过程复杂且环节繁多,如果通过某平台综合多个设计过程,必然可以简化流程,提高效率.在总结国内外相关文献的基础上,针对民用涡扇发动机,在Matlab/Simulink下,利用模块化方法构建包含稳态控制器、过渡态控制器以及极限保护器的涡扇发动机闭环控制系统仿真平台,并对其进行仿真测试和硬件在回路实验.结果表明,所构建的仿真平台满足控制系统的性能和实时性要求,具有良好的工程适用性.     

针刺C/C复合材料拉伸强度及渐进失效数值预测

基于金相显微镜观测的针刺C/C复合材料细观结构,考虑材料内部纤维的真实分布,建立了针刺C/C复合材料单胞模型。采用Linde失效准则,考虑纤维渐进损伤对材料进行了刚度折减,通过引入周期性位移边界条件,对针刺C/C复合材料的拉伸破坏进行了有限元法（FEM）数值模拟,分析了单胞模型的渐进失效过程,并预测了材料的拉伸强度。开展了针刺C/C复合材料拉伸试验,采用扫描电子显微镜（SEM）观察了材料的断口形貌,数值预测结果与试验吻合良好。针刺C/C复合材料受拉伸载荷后发生准脆性断裂,拉伸应力-应变曲线呈双线性,0°无纬碳布发生纤维断裂和基体开裂破坏,90°无纬碳布出现横向基体劈裂,最终断裂发生在针刺纤维与面内无纬碳布交叉区域。     

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

A dimension reduced INS/VNS integrated navigation method for planetary rovers

Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods.     

含激波的湍流流动高精度大涡数值模拟方法

针对采用亚格子模型进行含激波的湍流流动模拟时会面临激波附近的精度损失问题,考虑从通过亚格子模型以及数值模拟方法两方面的改进来实现湍流流动大涡模拟的精度提高.大涡模拟采用了Yee及Sj(o)green (2009)提出的高阶低耗散方法.该方法采用自适应的流场探测器以控制计算中所需区域的数值耗散,并考虑对动力学模型采用在激波位置使用Sagaut和Germano(2005)提出的单边亚格子过滤器和(或)直接禁用亚格子项等方法加以改进.对于标准的马赫数1.5和3条件下的激波-湍流干扰问题,上述新方法相较于全区域采用亚格子模型的方法均表现出了相似的精度提升.同时实现的数值精度改进方案采用了Harten的亚单元分辨过程来定位和锐化激波,并在精确激波位置附近的网格点处采用了单边测试滤波.     

C/SiC复合材料反射镜研究进展

反射镜在空间光学系统中起着非常关键的作用,目前已发展到第四代C/SiC复合材料。C/SiC复合材料具有低密度、高模高强、结构设计灵活等优点,已成为非常重要的新型反射镜材料。本文对四代反射镜的特点进行了归纳和对比,对C/SiC复合材料反射镜的结构设计、几种常用的制备工艺进行了整理和总结,并对目前国内外的研究进展进行了综述。     

轨/姿控发动机试验数据快速自动处理技术

轨/姿控发动机试验数据需即时提供,大量数据的快速自动处理技术未见报道。在简述了高空模拟试验特点、Pacific6000原理及数据文件结构后,分析了当前计算方法优缺点;在此基础上,将网络脚本语言的设计思想引入试验数据处理过程,提出了实现数据快速处理的数据流式算法,进而形成自动处理技术;基于此算法开发了工程应用软件,在实际试验中应用,取得了良好效果。该技术对类似计算和海量数据的快速处理具重要工程参考意义。     

New results and questions of lunar exploration from SELENE,Chang’E-1, Chandrayaan-1 and LRO/LCROSS

The moon has longstanding questions such as lunar environments, origin, formation and evolution, magnetization of crustal rocks, internal structure and possible life. The recent lunar missions, e.g., SELenological and ENgineering Explorer “KAGUYA” (SELENE), Chang’E-1, Chandrayaan-1, and Lunar Reconnaissance Orbiter/Lunar CRater Observation and Sensing Satellite (LRO/LCROSS), have provided new opportunities to explore and understand these issues. In this paper, we reviewed and presented the results and findings in the fields of lunar gravity, magnetic field, atmosphere, surface geomorphology and compositional variations, volcano, craters, internal structure, water and life science from new lunar exploration missions. In addition, the new objectives and scientific questions on lunar explorations in near future are presented and discussed.