基于N-S方程的悬停旋翼桨叶气动干扰数值模拟

采用基于N-S方程的CFD方法,通过计算前后平行放置的双翼和三翼的干扰流场,对悬停状态旋翼桨叶之间的气动干扰机理进行了数值探讨;在此基础上,进行了2种桨叶片数、2种桨距及2种桨尖马赫数情况的旋翼悬停流场对比计算,模拟它们对旋翼气动性能和桨叶间气动干扰作用的影响,得到一些与工程实际吻合的现象和结论。     

投入产出理论中两种消耗系数关系的新推证

从随机过程中状态转移矩阵的概仿出发，对投入产出理论中从直接消耗系数Ａ求得完全消耗系数矩阵Ｔ，提出一种新的推证方法，证明了Ａ与Ｔ之间的数量依存关系。     

连续型和非连续型蜂窝芯材的共振吸声结构性能研究

以芳纶纸蜂窝、内嵌树脂隔板和微穿孔面板为原料,制备了连续和非连续双自由度共振吸声结构,对两种共振吸声结构的力学性能和吸声系数进行对比研究。结果表明：连续蜂窝芯材所制备共振吸声结构的压缩和拉伸性能高于非连续型共振吸声结构,其中非稳定型压缩强度和拉伸强度高19%,稳定型压缩强度高32%,稳定型压缩模量高43%,剪切性能基本相当;两层蜂窝芯材容易出现孔格错位（非连续型共振吸声结构）,引起错位区域的微孔堵塞,使该结构的共振吸收峰与理论值出现较大差异。     

中值定理的应用探讨

通过典型例题，对微分中值定理，积分中值定理在求特殊函数的极限及有关命题，证明等式、不等式方面做了深刻地阐述，探讨怎样正确、理解、应用好中值定理。     

Prediction of horizontal gas–solid flows under different gravitational fields

In this paper the performance of horizontal pneumatic conveying under different gravity environments is evaluated. An Euler–Lagrange approach validated versus ground experiments is employed to predict the relevant particle variables such as particle mass flux, mean conveying and fluctuating velocities in terrestrial, lunar and micro-gravity conditions. Gravity reduced computations predict a reduction in the global particle–wall collision frequency. Also, in the case of low wall roughness and small particle mass loading, reduction of gravity acceleration implies an increase of particle–wall collision frequency with the upper wall of the channel affecting greatly the particle mass flux profile. In the case of high wall roughness and/or high particle-to-fluid mass loading (i.e., around 1.0) particle conveying characteristics are similar in the three gravity conditions evaluated. This is due to the fact that both, wall roughness and inter-particle collisions reduce gravitational settling. However, the influence of gravity on the additional pressure loss along the channel due to the conveying of the particles is much reduced.     

基于Lagrange方法的单旋翼飞行器动力学建模

为了进行微小型单旋翼飞行器的动力学建模,通过建立多个坐标系来反映各部分间的相对运动.首先,利用坐标变换得到位置、速度及加速度等向量,并代入拉格朗日方程得到运动学模型;然后,对模型进行数值求解,得到飞行器的姿态响应.仿真结果表明,飞行器定点盘旋时合外力为零,能量保持不变;爬升或前飞时有非保守力做正功,能量增大.     

Calculation of the barometric coefficients at the start of the 24th solar activity cycle for particle detectors of Aragats Space Environmental Center

After the major modernization of the data acquisition electronics of the particle detectors operated at Aragats Space Environmental Center (ASEC) calculations of the barometric coefficients of all the monitors were performed in the beginning of the 24th solar activity cycle. The barometric coefficients of particle detectors located at altitudes of 1000 m, 2000 m and 3200 m a.s.l. measuring various secondary cosmic ray fluxes were compared with theoretical expectations and monitors operated on different longitudes and latitudes. The barometric coefficients were also calculated for the several neutron monitors of recently established Eurasian database (NMDB) and SEVAN particle detector networks. The latitude and altitude dependencies of the barometric coefficients were investigated, as well as the dependence of coefficients on energy of the primary particles.     

用整体传递系数法分析转子系统动力特性

整体传递系数法是在传递系数法的基础上,引入整体矩阵实现多子结构整体传递的一种用于转子系统动力特性分析的新型方法.整体传递系数法对于解决多转子(或机匣)相互耦合系统的问题有其独特的优点:节省计算时间,节省内存,采取状态参量中的位移项代替力项,可以消除传统的传递矩阵中的数值不稳定现象.利用此方法进行了多转子耦合系统的临界转速和振型的计算,结果表明,计算速度和数值的稳定性与其它传递矩阵法相比具有明显的提高.     

典型阶梯篦齿高转速密封性能试验

在高转速密封试验设备上,进行了实际尺寸阶梯篦齿压比(1.05～28)、相对密封间隙(齿尖密封间隙和齿宽比)(24～40)、泄漏流雷诺数(1900～28000)及旋转速度(0～12000r/min)等对密封性能影响的试验。结果显示:篦齿流量系数随压比变大而上升,随相对密封间隙变大而降低;转速低于5000r/min时,旋转对篦齿流量系数影响不明显,高转速、小压比时,篦齿流量系数随转速的升高而降低,降幅超过301%;较小雷诺数下,篦齿流量系数随雷诺数的减小快速降低,雷诺数超过6000以后,篦齿流量系数受雷诺数的影响不明显;气流通过阶梯篦齿第一道齿的压力损失最小,通过最后一道齿的压力损失最大,通过中间各齿的压力损失相当。基于试验测试数据,修正了典型阶梯篦齿流量系数的求解关系式,修正后的关系式计算值与实测值吻合良好。      

Developing an engineering-statistical model for estimating aerodynamic coeffcients of helicopter fuselage

The design of the geometric shape of a helicopter fuselage poses a serious challenge for designers. The most important parameter in determining the shape of the helicopter fuselage is its aerodynamic coefficients. These coefficients are determined using two methods:wind tunnel test and computational fluid dynamics (CFD) simulation. The first method is expensive, time-consuming and limited. In addition, estimates in regions away from data can be poor. The second method, due to the limitations of numerical solution, the number of nodes and the used solution, is often inaccurate. In this paper, with the aim of accelerating the design process and achieving results with reasonable engineering accuracy, an engineering-statistical model which is useful for estimating the aerodynamic coefficients was developed, which mitigated the drawbacks of these two methods. First, by combining CFD simulation and regression techniques, an engineering model was pre-sented for the estimation of aerodynamic coefficients. Then, by using the data from a wind tunnel test and implementation of statistical adjustment, the engineering model was modified and an engineering-statistical model was obtained. By spending less time and cost, the final model provided the aerodynamic coefficients of a helicopter fuselage at the desired angles of attack with reasonable accuracy. Finally, three numerical examples were provided to illustrate the application of the pro-posed model. Comparative results demonstrate the effectiveness of the engineering-statistical model in estimating the aerodynamic coefficients of a helicopter fuselage.