Influence of pre-tension on ballistic impact performance of multi-layer Kevlar 49 woven fabrics for gas turbine engine containment systems

In this paper, ballistic impact tests on wrapped multi-layer Kevlar 49 woven fabric systems were carried out with a flat blade projectile to investigate the impact response during a fan blade out event. The influences of the number of Kevlar layers and pre-tension were discussed particularly. Test results were used to analyze failure modes and energy absorption characteristics of multi-ply Kevlar fabrics. Results show that there are two kinds of impact damage for fabrics: global deformation mainly involving stretching of yarns in the impact region and fabric wrinkle from both sides to the impact zone, and local damage characterized by yarn fracture, yarn pull-out, and yarn unraveling. The energy absorption capability of Kevlar 49 woven fabrics improves with the number of fabric layers. The energy absorbed by multi-layer fabrics increases slightly at the beginning and then decreases substantially with pre-tension. The work in this paper can provide guidance for designing light-weight multi-layer fabrics containment systems.     

着陆缓冲装置特性分析及控制方法研究

着陆缓冲技术在航天器回收系统中的应用日益广泛,文章对着陆缓冲过程所使用的两种发动机推力制度进行了比较;分析了着陆缓冲过程中影响系统最终性能的因素。认为影响最大的因素是初始条件和环境条件的改变,对此提出了一种较为实用的控制方法。应用这一方法,可以最大限度地消除初始条件和环境条件的改变对着陆缓冲装置性能的影响。     

混杂复合材料层合板抗冲击性能研究

为了探究复合材料层合板在实际应用中因承受冲击载荷而造成的结构安全问题,本研究采用实验和仿真相结合的方法,首先探究冲头形状对复合材料层合板损伤机理的影响,然后结合不同冲击能进一步揭示层合板的承载力和能量吸收变化规律。结果表明,相同冲击能下,层合板的损伤范围和承载力随着圆锥头、半球头、平头依次增加;相应的层合板的临界穿透能量随着圆锥头、半球头、平头依次增大;冲头形状和冲击能对层合板的吸能能力有较大的影响。     

图像序列中机动目标三维运动和结构的计算

综合视觉运动分析中的2类处理方法,选取图像中的角点作为特征点,在理论上证明了图像序列的光流场可以近似地用角点的位移场代替。利用已有文献中的建模思想,详细推导出递归计算机动目标三维运动和结构的非线性计算模型,采用广义卡尔曼滤波(EKF)递归地计算图像序列中机动目标的三维运动和结构。合成图像序列和真实图像序列实验结果表明该算法能取得较好的效果。     

GPS精密点定位的数据处理

在GPS精密点定位数据处理中,通常采用所谓无差分模型.然而,GPS单站观测量也可通过不同差分组合以减少未知参数数目,且在理论上与无差分模型等价.文中利用实际GPS观测数据,比较了不同点定位差分模型的定位精度和其他指标.     

单幅图像的三维重构视觉系统特征点提取算法的研究与实现

实现基于单幅二维图像不标定欧氏重构三维场景的关键技术之一是有效提取彩色伪随机编码图像特征角点。为给图像特征点匹配提供更多的样本信息,采用定位于彩色图像Harris算子探测特征角点,并动态给出角点响应的自适应阈值条件。特征点提取实验及三维欧氏重构结果证实了该方法的适用性和有效性。     

30cm离子推力器在轨环境下的工作点及热控措施研究

栅极间距变化是影响离子推力器在轨环境下从冷态条件正常点火启动的重要因素,同时也决定了离子推力器的在轨工作时机和热控实施策略。本文采用有限元仿真与地面热平衡试验验证相结合的方法,建立起30cm离子推力器有限元分析模型并进行了模型校验,之后对离子推力器在轨受太阳光照影响的栅极温度场分布和间距变化,以及推力器在5kW工况下的三个典型温度点所对应的栅极间距变化进行了仿真分析,最后考虑了主动热控干预对推力器最恶劣工作点的栅极间距变化影响。结果显示：纯太阳光照影响下的栅极组件存在周期性温度变化,栅极最大温差可达到100℃,栅间距缩小量在0.06mm~0.16mm范围内波动;在太阳光照基础上实施60W的主动热控后,栅极最大温差降低至60℃,栅间距缩小量波动范围则变为0~0.03mm;栅极最高温度点和最低温度点分别是推力器冷态启动最容易和最困难的两个工作时机点,两点所对应的启动后屏栅和加速栅最小间距分别为0.22mm和0.04mm;在10W、70W和120W的热控加热功率下,从最低温度点启动后的屏栅和加速栅最小间距分别为0.06mm、0.20mm和0.29mm;采取主动热控措施能够有效降低推力器工作过程中的栅极热形变位移峰值,且加热功率为120W即温控点温度为50℃的主动热控可以满足30cm离子推力器在轨冷态启动时的0.25mm安全栅极间距要求。     

基于空间电压矢量的软起动器变频阶段的优化及仿真

对于空间电压矢量软起动器变频阶段的负相转矩和转速振荡问题,依据电压矢量的控制方法,对频率转换点的选取实行优化。以电机负载状况来获取各个变频阶段的控制角初始值,以恒压频比原则获取控制角终值,以此对软起动器变频阶段的控制进行优化。最后对优化后的软起动器进行仿真验证,结果显示,软起动器工作在变频阶段时,在频率转换点出现的转速超调得到了改善,电流峰值有所减小,没有负转矩出现。     

An adaptive fast fixed-time guidance law with an impact angle constraint for intercepting maneuvering targets

Sliding mode guidance laws based on a conventional terminal sliding mode guarantees only finite-time convergence, which verifies that the settling time is required to be estimated by selecting appropriate initial launched conditions. However, rapid convergence to a desired impact angle within a uniform bounded finite time is important in most practical guidance applications. A uniformly finite-time/fixed-time convergent guidance law means that the convergence (settling) time is predefined independently on initial conditions, that is, a closed-loop convergence time can be estimated a priori by guidance parameters. In this paper, a novel adaptive fast fixed-time sliding mode guidance law to intercept maneuver targets at a desired impact angle from any initial heading angle, with no problems of singularity and chattering, is designed. The proposed guidance law achieves system stabilization within bounded settling time independent on initial conditions and achieves more rapid convergence than those of fixed-time stable control methods by accelerating the convergence rate when the system is close to the origin. The achieved acceleration-magnitude constraints are rigorously enforced, and the chattering-free property is guaranteed by adaptive switching gains. Extensive numerical simulations are presented to validate the efficiency and superiority of the proposed guidance law for different initial engagement geometries and impact angles.     

航空发动机机匣摆线粗加工轨迹规划方法

针对机匣零件粗加工过程中凸台多、加工余量大、材料难切削、刀具磨损快、加工周期长等特点,提出了一种机匣摆线粗加工刀具轨迹规划方法,该方法能有效控制切削过程中刀具负载的变化,改善刀具切削过程中的加热-冷却循环,减缓刀具的磨损,提高机匣粗加工效率。首先,通过对两种摆线模型的分析,建立了摆线铣数学模型,并分析了摆线铣的优缺点;其次,结合机匣零件特点,将模型在精度范围内离散为点模型,利用圆锥将模型展开并建立展开模型与原始模型间的映射关系。通过对可加工区域的划分和平面逼近,生成了适用于机匣零件的摆线粗加工刀具轨迹。最后,分别通过摆线铣刀具磨损实验、平面型腔摆线铣实验和机匣摆线铣实验,验证了摆线铣在降低刀具磨损、延长刀具寿命方面的有效性,以及本文轨迹生成算法在航空发动机机匣实际加工中的正确性和高效性。研究成果能有效缩短加工周期、降低加工成本,提升机匣零件的粗加工效率。