Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

凹腔对一体化支板火焰稳定器燃烧性能的影响

在来流温度为780~850℃、来流马赫数为0.16及油气比为0.002~0.006的条件下,试验研究了凹腔对喷油/稳定一体化支板火焰稳定器燃烧效率及熄火性能的影响,并结合数值模拟进行辅助分析。结果表明:在不同油气比条件下,带凹腔的一体化支板火焰稳定器均能实现稳定高效燃烧;不带凹腔的一体化支板火焰稳定器燃烧效率始终低于带凹腔的一体化支板火焰稳定器,随着油气比的增加,两者燃烧效率差距逐渐缩小;带凹腔的一体化支板火焰稳定器较不带凹腔的一体化支板火焰稳定器有更好的熄火性能;凹腔结构促进了燃油雾化与蒸发,从而提高一体化支板火焰稳定器的燃烧性能。      

Design and optimization of a novel electrically controlled high pressure fuel injection system for heavy fuel aircraft piston engine

The heavy fuel compression ignition engines are widely equipped as aircraft piston engines. The fuel injection system is one of the key technologies that determines the performance of engine. One of the main challenges is to precisely control the injected fuel quantity and flow rate in the presence of pressure fluctuation. This challenge is even more serious for heavy fuel. An original design for electrically controlled high pressure fuel injection system called Multi-Pumppressure-reservoirs fuel injection System(MPS) was demonstrated to reduce the pressure fluctuation and help keep injection stable. MPS was compared with an ordinary high pressure Common Rail fuel injection System(CRS). This work established one-dimensional AMESim and mathematical models for both CRS and MPS to study the effect of different structures and geometric parameters on the pressure fluctuations. The calculations show that the average fuel pressure fluctuation of MPS can be reduced by 57% for the crankshaft speed of 1900 r/min, and the pressure fluctuation before injection reduced by 100%. It is concluded that the pressure performance of MPS is less sensitive to pressure reservoir volume than that of CRS, and there is an opportunity for further volume reduction.     

基于旋转高频信号注入法的内置式永磁同步电机低速段转子位置检测及其误差补偿

旋转高频信号注入法注入信号较为稳定,且位置估计过程不依赖电机参数,因而十分适用于内置式永磁同步电机(IPMSM)的零、低速转子位置检测。针对传统高频信号注入法无法辨别磁极的问题,用电压方波注入法检测磁极,结合有限元软件仿真,来合理选取方波电压幅值和时长,有效缩短了磁极判断耗时。分析了滤波器和信号离散化对位置估计精度的影响,提出在低速段可用线段拟合带通滤波器中心频率处的相频特性曲线,推导所需补偿角度与电机转速的关系。在理论分析的基础上,采用基于DSP28335的样机平台进行试验,结果表明磁极判断过程稳定,耗时较短,补偿后的位置估计值相比补偿前有明显改善,调速过程中系统动态性能良好。     

离心式喷嘴工况理论分析

对离心式喷嘴的最大流量原理进行了证明，并求得了该原理成立的边界条件。分析了离心式喷嘴的工况，结果表明，当喷嘴压降等于或大于临界截面处平均余区的１．５倍时，其工况处于临界或超临界状态。导出了波沿离心式喷嘴中液体自由表面的传播速度及其频率的计算公式，从中可以看出，波的传播速度及其频率取决于喷嘴压降及喷嘴的几何特性。     

相似理论在层板式喷注器试验研究中的应用

将相似理论应用于层板式喷注器的试验研究，利用自行设计的溅板式喷嘴进行了冷流试验，通过试验证明该喷嘴的原形件与模型件在满足几何相似且进入第二自模区的条件下，流动特性相似。最后阐述了此结论的重要意义。     

高速飞行器用射流预冷却涡轮基发动机性能模拟

根据预冷却涡轮基发动机的工作机理,建立了考虑变比热的计算预冷却涡轮基发动机性能的数学模型,编制了相应的计算软件;并以某小型涡喷发动机为例,沿飞行轨迹计算分析了射流预冷却对发动机性能的影响。从计算结果可以看出,采用喷流预冷却方式,可以大大扩展常规涡轮喷气发动机的工作范围,能够满足高速飞行器或两级入轨飞行器第一级动力装置的要求。     

跃变型介质中原油渗流有限元计算

本文建立跃变型介质中原油渗流的数学模型,可用来描述油层(尤其是低渗透层)超高压注水条件下的不稳定渗流过程及其特征。用Galerkin有限元法进行了数值计算,讨论了介质跃变的影响。     

来流马赫数对射流矢量喷管内流场影响的动态模拟

以二维拉瓦尔喷管为对象,利用非定常雷诺平均N—S方程和RNGκ-ε两方程湍流模型对激波控制的射流推力矢量喷管非定常流场进行研究,分析了来流马赫数连续变化对喷管流场的影响,得出喷管推力性能的变化规律。结果表明：在亚声速来流中,轴向力随飞行马赫数增加而小幅上升,侧向力变化不大;在跨声速来流中,轴向推力和侧向推力都急剧下降;...     

气体二次喷射推力向量控制数值仿真

采用基于Favre平均的三维N-S方程和k-ε湍流模型对固体火箭发动机气体二次喷射推力向 量喷管复杂干扰内流场进行数值模拟;采用三阶精度空间差分格式和隐式Jacobi时间点迭代 方法进行求解;借助数值模拟技术对气体二次喷射推力向量喷管方案进行了初步探索,研究 了不同喷射条件对气体二次喷射流场特征及侧向控制力的影响作用;研究表明,二次喷射气 体喷射孔位置、总温及总压等因素对侧向力影响具有耦合作用,合适的喷射孔位置和高温燃 气以及较大喷射总压都能有效增加侧向力及向量角;燃气二次喷射系统具有较高的效率;侧 向力随二次喷射流总压增加而线性增大.