移15°双十二相隐极同步整流发电机数学模型的研究

分别在abc坐标系和dq0坐标系下建立了移15°双十二相隐极同步整流发电机的基本数学方程,推导了电机电压、磁链、输出功率、电磁转矩和转子运动方程。在MATLAB/Simulink中建立了移15°双十二相隐极同步整流发电机的仿真模型。对两路输出进行了不平衡负载仿真和试验。仿真与试验结果相比基本一致,验证了移15°双十二相隐极同步整流发电机数学模型的正确性。这为双十二相同步整流发电机运行性能和励磁控制系统的研究奠定了基础。     

模型预测控制在永磁同步电机系统中的应用发展综述

随着数字技术的发展,模型预测控制(MPC)已经广泛应用于交流传动系统。首先介绍了经典MPC策略——有限控制集MPC和连续控制集MPC的原理。其次综述了多步预测控制、多矢量预测控制、具有参数鲁棒性的预测控制、广义模型预测、显式模型预测这些常见的改进MPC的研究现状,并提出相关研究思路。最后,根据MPC的应用需求和研究现状,展望了未来需要进一步深入和拓展的研究方向。     

无刷双馈电机静止坐标系数学模型的研究

由于没有电刷和滑环,提高了运行的可靠性,降低了维护成本,因此无刷双馈电机(BDFM)在变速恒频发电领域有着广阔的应用前景。由于特殊的结构和工作原理,BDFM数学模型十分复杂。从BDFM多回路空间矢量数学模型出发,推导出了两个静止坐标系之间的坐标变换关系以及功率绕组静止坐标系数学模型和控制绕组静止坐标系数学模型,推导过程简洁明了。所得结果为BDFM理论分析和不同控制策略的研究提供了理论基础。MATLAB/Simulink环境下的仿真结果验证了数学模型及坐标变换关系的正确性。     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型;然后设计了一种能够自动调节补偿斜率的混沌控制信号;最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

点火瞬态过程仿真模型参数辨识

建立了固体火箭发动机点火瞬态过程一维非定常流场仿真模型,采用系统辨识方法进行了模型参数不确定性研究。基于点火试验用缩比发动机试验结果,得到了传热模型参数和瞬态燃速模型参数的最优估计,提高了点火瞬态过程一维仿真模型的预估精度。采用近似方法,构建Kriging近似函数,有效解决了一维非定常流场仿真的计算复杂性问题。     

价电子分形燃烧模型在高能固体推进剂中的应用

在价电子燃烧模型的基础上引进分形理论,提出复合固体推进剂的价电子分形燃烧模型,在此基础上进行了高能固体推进剂燃速和压强指数的模拟计算,研究了固体填料粒径和压力对燃速的影响规律。结果表明,价电子分形燃烧模型适用于高能固体推进剂的燃烧性能计算,燃速及压强指数模拟计算结果与测试结果吻合较好,大部分误差在±10%范围以内。     

机身复合材料加筋板壳的稳定性及强度分析系统

随着先进复合材料在飞机主承力结构（如机身结构）中的大量应用,工程上迫切需要大型复合材料加筋板壳的快速建模打样计算、稳定性（刚度）和强度分析的理论和程序支持。基于稳定性理论,并综合复合材料任意加筋板壳有限单元和复合材料层合板壳失效理论等方面的成果,开发了一个机身复合材料加筋板壳结构的稳定性及强度分析程序(CSSAP)。该程序系统不仅可以进行复合材料（加筋）板壳的线性稳定性和强度分析,还可进行非线性稳定性和强度分析;可对较粗的网格划分,得到临界屈曲应变和后屈曲时的应力。通过一些算例与文献结果的对比,表明本程序系统能够满足工程上的精度要求。并且,通过对实际机身一个典型复合材料加筋板壳的计算,表明本程序系统也可用于飞机工程复杂结构的分析。