基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

热处理对激光直接沉积成形A-100钢基体组织及性能的影响

研究了激光直接沉积成形A-100钢沉积态及热处理态组织,通过调整热处理工艺获得激光直接沉积成形A-100钢回火马氏体+回火贝氏体混合基体组织。不同热处理工艺下性能对比结果表明,相比淬火马氏体组织,回火贝氏体+回火马氏体混合组织具有更高的强度,但塑性有所下降。     

RTM用6818高温环氧树脂化学流变特性研究

以树脂传递模塑(RTM)用6818高温环氧树脂体系的化学流变特性研究为目的,以差示扫描量热法(DSC)和黏度实验为基础,采用外推法初步确定了6818树脂体系的固化工艺制度。依据双阿累尼乌斯方程建立了树脂体系的化学流变模型,模型曲线与实验数据的吻合性良好。模型分析表明,在80～100℃内树脂体系黏度低于200 mPa·s的时间大于12 h,可以作为6818树脂比较理想的注胶温度。该模型能够反映6818树脂黏度变化规律,预报该树脂体系的RTM工艺窗口。     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

进气畸变条件下压气机转子叶片的 振动特性研究

航空发动机研制及适航要求中均明确提出发动机零部件的振动特性分析和测试要求,包括评估进气流场畸变对振动特性的影响。对某航空发动机压气机第1级转子叶片进行振动特性计算分析,开展自然进气和进气畸变条件下的叶片振动应力测试。计算分析和测试结果表明:计算分析结果与自然进气条件下测试的叶片共振转速及振动频率一致性好,其激振源主要是压气机结构因素;在进气畸变条件下激振源更丰富,与自然进气条件相比,叶片会被激起额外的振动,且在同一共振转速下振动幅值较大,进气畸变对转子叶片的振动特性产生重要影响。在发动机研制过程中,为提高叶片工作的可靠性,需要加强进气畸变条件下的叶片振动特性试验研究。     

高温处理对中密度针刺C/C复合材料性能的影响

针对C/C复合材料脆性问题,对密度为1.60 g/cm3的碳布叠层针刺C/C复合材料进行了1800、2 000、2 200和2 500℃的高温处理,研究了不同热处理温度对C/C复合材料微晶结构、力学和抗热震等性能的影响.结果表明,高温处理使针刺C/C复合材料的层间剪切和面内拉伸强度出现不同程度的降低,但材料的断裂伸长率和抗热震性能得到大幅度提高.其中,1 800℃高温处理后的C/C复合材料具有优异的力学和抗热震性能.     

冲压发动机气膜冷却分析模型

本文建立了冲压发动机燃烧室气膜冷却传热分析程序。根据燃烧室设计的技术要求,从冷却性能角度完成气膜冷却系统的气动性能和传热特性分析,提供冷却结构优化所需的信息。     

氢氧火箭发动机羽烟紫外辐射参数反演研究

针对氢氧火箭发动机羽烟紫外辐射特性参数分析,提出一种基于紫外CCD(change coupled device)相机采集的单幅辐射图像,同时反演羽烟内紫外辐射源项和吸收系数的方法.该方法将羽烟简化为发射-吸收轴对称介质,通过对辐射图像数据进行Able变换得到三维介质内辐射强度分布,利用最小二乘法将反演问题转化为使计算得到的与Abel变换得到的辐射强度误差最小的最优化问题,然后利用共轭梯度法求解该最优化问题.通过在求解正问题得到的准确值的基础上添加随机噪声,模拟辐射图像数据,分析了测量误差对算法反演精度的影响.结果表明:该算法对测量误差不敏感,能够准确的重建羽烟内的辐射源项和吸收系数分布.      

Preliminary study on heat flux measurement data of TT-0 flight test

With the explosive development of aerospace science, the design of the new generation airliner at higher speeds is attracting more attentions. To achieve this goal, it is necessary to achieve accurate prediction of the aerodynamic heating / force loads and successful reduction of drag and heat flux. As a remedy for the existing studies which are based upon the CFD and wind tunnel tests, this study presents a flight test for the drag and heat reduction spike technology. The principal goals of this flight test were to provide reference for verifying the accuracy of the prediction technology on ground and promote the development of the drag and heat reduction technology. By adopting the OS-X rocket, the TT-0 test vehicle designed by Shenyang Aircraft Design & Research Institute reached a maximum Mach number of 5.8 and a maximum altitude of 38 km. Hypersonic and supersonic pressure data by pressure scanning valves and heat fluxes by gauges at different locations were obtained successfully. Also, heat fluxes obtained by in-house CFD code are illustrated in comparison with the flight data. The results indicate that the numerical errors are large in most cases. More technologies, such as more CFD codes and more numerical procedures, should be adopted to conduct studies on this issue in the future.     

原子层热电堆热流传感器在激波风洞试验中的应用

高超声速边界层转捩及激波-边界层干扰等基础气动问题的风洞试验中,高频脉动热流是一重要测试量.为了验证自研的原子层热电堆热流传感器在实际风洞试验环境中的性能,利用尖锥模型在Φ2m激波风洞(FD-14A)内开展来流马赫数10、单位雷诺数4.7×106/m等流场条件下的风洞试验,并与高频脉动压力传感器对比,热流测试结果反映出...