廊坊市新农村建设中的生态环境存在的问题及对策

和全国其他地方一样,廊坊市在大力推进社会主义新农村建设的过程中,也面临着农村生态环境恶化的困境。为了实现农业生产发展和农村生态环境保护之间的平衡,政府应当加大公共财政支出向农村地区倾斜的力度,坚持规划先行、服务跟进的原则,切实改善人居环境,强化农村生态环境保护法制的实施,把新农村建设成为生态良好的新农村。     

野战环境下大型飞机超低空气动特性分析

针对野战环境下的大型飞机超低空飞行,采用CFD方法对地面存在前向或横向不对称障碍物时地面效应对气动参数的影响进行了数值分析,包括纵向稳定性和侧向摇晃等问题.研究结果表明,野战等非常规飞行条件下,地面不确定障碍物会造成大型飞机稳定性变差,严重时可能出现纵向点头和横侧向摇晃现象,容易导致触地危险.最后,从现代飞行控制理论角度提出了对常规布局大型飞机进行闭环控制的研究思路.     

新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响

通过金相观察(OM)、扫描电镜(SEM)以及拉伸测试系统地表征和研究了热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响。研究表明:固溶态GW94、GW74、GW44合金主要由α-Mg过饱和固溶体、铸态残留相Mg5(Gd,Y)以及固溶过程形成的方块相组成。随着Gd含量的增加,固溶态Mg-Gd-Y合金中方块相的体积分数不断增加;在同一时效温度下,合金达到时效峰值的时效时间缩短;室温下拉伸的固溶态、时效峰值态合金以及200和250℃下拉伸的时效峰值态合金的抗拉强度和屈服强度不断提高(固溶态合金屈服强度先降低后升高),但是伸长率却是不断降低。时效峰值态GW94合金表现出优越的力学性能,室温时其抗拉强度和屈服强度分别为300、247 MPa,而伸长率仅为0.9%;200和250℃拉伸时,时效峰值态GW94合金抗拉强度、屈服强度和伸长率分别为329、234 MPa和2.6%以及312、233 MPa和2.7%。时效峰值态GW94、GW74合金出现抗拉强度随温度升高而升高的反常力学行为。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

舱内航天服散热途径分析

为分析常压下航天员穿着舱内航天服时的散热性能，６名健康男性青年按二次复合设计分组共进行２４人次试验，经分析计算了获得了服装各散热途径的散热率随通风气源参数及人体活动水平变化的数学模型。对影响服装散热性能的因素及服装散热特性进行了分析讨论。     

Integrity of sulfur concrete subjected to simulated lunar temperature cycles

In view of potential application as a construction material on the lunar surface the mechanical integrity of sulfur concrete was evaluated after being subjected to simulated temperature cycles. Here, small cubes of sulfur concrete were repeatedly cycled between room (20 °C) and liquid nitrogen (−191 °C) temperatures after which they, and non-cycled cubes, were evaluated by compression testing. The compression strength of the non-cycled samples averaged ∼35 MPa (5076 psi) before failing whereas the cycled samples fractured at about 7 MPa (1015 psi). Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate whereas it was seen adhering in those non-cycled. Based on a simple analysis it was concluded that the large strength discrepancy between cycled and non-cycled samples is due to differences between the coefficients of thermal expansion of the materials constituting the concrete.