新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响

通过金相观察(OM)、扫描电镜(SEM)以及拉伸测试系统地表征和研究了热处理对砂型铸造Mg-Gd-Y合金微观组织和力学性能的影响。研究表明:固溶态GW94、GW74、GW44合金主要由α-Mg过饱和固溶体、铸态残留相Mg5(Gd,Y)以及固溶过程形成的方块相组成。随着Gd含量的增加,固溶态Mg-Gd-Y合金中方块相的体积分数不断增加;在同一时效温度下,合金达到时效峰值的时效时间缩短;室温下拉伸的固溶态、时效峰值态合金以及200和250℃下拉伸的时效峰值态合金的抗拉强度和屈服强度不断提高(固溶态合金屈服强度先降低后升高),但是伸长率却是不断降低。时效峰值态GW94合金表现出优越的力学性能,室温时其抗拉强度和屈服强度分别为300、247 MPa,而伸长率仅为0.9%;200和250℃拉伸时,时效峰值态GW94合金抗拉强度、屈服强度和伸长率分别为329、234 MPa和2.6%以及312、233 MPa和2.7%。时效峰值态GW94、GW74合金出现抗拉强度随温度升高而升高的反常力学行为。     

基于自适应网格的超声速液体射流破碎过程研究

为研究超声速气流中液体横向射流的破碎过程,采用脉冲背景光方法和VOF方法开展了实验和数值研究。为提高液体横向射流中气液界面和气流场特征捕捉的精确性,采用自适应网格技术对于气液界面、激波出现位置进行网格细化,计算得到了较为精细的气液界面、激波特征及涡系结构。研究结果表明:在低成本仿真模拟条件下,利用自适应网格计算得到的射流轨迹和轮廓与实验吻合较好,射流轨迹的最大误差为10%;射流初始段在超声速气流条件下,仍然存在一段高度约为1.9倍喷孔直径且圆柱形态保持较好的连续光滑液柱。随着喷注压降的升高,液柱的长度逐渐增大;主流气体流经液柱发生三维绕流,在射流附近和近壁面区域形成不断演化的反转涡对,反转涡对的形成加速了液体射流一次破碎过程。     

展向振荡对激波/湍流边界层干扰的影响

周期振荡作为一种有效的壁面流动控制手段受到广泛关注,而其对激波/湍流边界层干扰的影响目前鲜有研究。本文采用高精度直接数值模拟（DNS）方法对马赫数2.9、12°激波入射角、强振荡下的激波/湍流边界层干扰进行了系统研究。通过与无振荡工况的定量比较,揭示了展向强振荡对干扰区内复杂流动结构的影响规律及作用机制,如分离泡尺度、物面压力脉动非定常特性、物面剪切的非定常特性及统计特征等。研究发现：在展向强振荡作用下,分离点位置提前,间歇区长度增大;同时由于分离泡内强黏性耗散的影响,展向振荡的穿透高度约为分离泡高度的4%,因而对流动结构不会产生实质影响。但展向强振荡会对壁面附近流动造成显著影响,如强振荡诱导的壁面展向速度远大于流向速度,造成流向剪切与展向剪切之间夹角的概率密度函数峰值从0°偏移到80°~90°之间。物面压力及剪切本征正交分解分析表明,展向振荡会导致模态能量从低阶模态向高阶模态转移,降低低频运动的能量占比,增强再附后Görtler涡等壁面附近旋涡结构的强度。     

超声速膨胀角入射激波/湍流边界层干扰直接数值模拟

为了揭示膨胀效应对激波/湍流边界层干扰区内复杂流动现象的影响规律,采用直接数值模拟方法对来流马赫数2.9、30°激波角的入射激波与10°膨胀角湍流边界层相互作用问题进行了数值研究。系统地探讨了激波入射点分别位于膨胀角上游、膨胀角角点和膨胀角下游3种工况下膨胀角干扰区内若干基本流动现象,如分离泡、物面压力脉动及激波非定常运动、湍流边界层统计特性和相干结构动力学过程等。结果表明,激波入射点流向位置改变对分离区流向和法向尺度的影响显著,尤其是当激波入射点位于角点及其下游区域。研究发现,膨胀角干扰区内物面压力脉动强度急剧减小,分离区内压力波向下游传播速度将降低而在膨胀区内将升高,膨胀效应极大地抑制了分离激波的低频振荡运动。相较于入射激波与平板湍流边界层干扰,入射激波流向位置改变对膨胀角再附区速度剖面对数区及尾迹区影响显著,将导致其内层结构参数升高而外层降低,近壁区内将呈现远离一组元湍流状态的趋势。此外,流向速度脉动场本征正交分解分析指出,主模态空间结构集中在分离激波及剪切层根部附近而高阶模态以边界层内小尺度正负交替脉动结构为主。低阶重构流场结果表明,前者对应为分离泡低频膨胀/收缩过程而后者表征为分离泡高频脉动。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。