Preliminary study on heat flux measurement data of TT-0 flight test

With the explosive development of aerospace science, the design of the new generation airliner at higher speeds is attracting more attentions. To achieve this goal, it is necessary to achieve accurate prediction of the aerodynamic heating / force loads and successful reduction of drag and heat flux. As a remedy for the existing studies which are based upon the CFD and wind tunnel tests, this study presents a flight test for the drag and heat reduction spike technology. The principal goals of this flight test were to provide reference for verifying the accuracy of the prediction technology on ground and promote the development of the drag and heat reduction technology. By adopting the OS-X rocket, the TT-0 test vehicle designed by Shenyang Aircraft Design & Research Institute reached a maximum Mach number of 5.8 and a maximum altitude of 38 km. Hypersonic and supersonic pressure data by pressure scanning valves and heat fluxes by gauges at different locations were obtained successfully. Also, heat fluxes obtained by in-house CFD code are illustrated in comparison with the flight data. The results indicate that the numerical errors are large in most cases. More technologies, such as more CFD codes and more numerical procedures, should be adopted to conduct studies on this issue in the future.     

基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

新型翅片式减涡器减阻特性数值研究

为了降低压气机径向引气过程中的压力损失,在设计出新型翅片单元结构的基础上,研究了新型翅片单元结构对径向引气压力损失的影响规律,对不同转速、新型翅片结构的去旋系统开展了数值研究,得到了不同工况下压气机共转盘腔径向引气的流场结构及压力损失分布曲线。研究结构表明:新型翅片单元结构能够抑制盘腔内气流旋流比,降低引气压力损失;翅片单元通道宽度和高度均存在最佳值使得减涡器减阻效果较好,在优选结构翅片单元通道宽度L=0.78,通道高度R3=0.97的条件下,其减阻效果较简单盘腔模型提高86.5%。高低翅片结构能起到较好的减阻效果,随着单侧翅片高度的升高减阻效果逐渐增强,在本文结构下增加单侧翅片高度L1=0.3时减阻效果最优,且A侧或B侧翅片增加带来的减阻效益相同。一方面,最优高低翅片结构其减阻性能相比于简单盘腔模型、典型翅片式减涡器模型以及翅片单元通道宽度L=0.78,通道高度R3=0.97的结构模型分别提高87.5%,29%,7.8%;另一方面,最优高低翅片结构能够减轻翅片单元的质量,具有较高的工程应用价值。     

下缘板孔对涡轮叶片尾缘内冷通道流动换热影响的数值研究

涡轮叶片下缘板出气孔对内冷通道的流动和换热性能有较大影响。通过数值模拟方法研究下缘板出 气孔对尾缘和下缘板双路出气涡轮叶片尾缘内冷通道内的流动和换热特性,对比分析孔径、孔形和孔位置对尾 缘溢流孔流量系数、尾缘出流比、尾缘通道内总压系数和尾缘内冷腔壁面换热特性的影响。结果表明:下缘板 出气孔孔径对流量系数分布的影响显著,孔径增大,尾缘溢流孔流量系数下降,尾缘出流比减小,尾缘内冷通道 内压力损失降低,内冷腔平均换热系数增大;孔形对上游内冷通道内流动和换热几乎没有影响;孔位置变化对 内冷通道壁面整体的换热系数影响很小,对局部影响较大。     

感应同步器，光栅和磁栅兼容的数显表的研究

本文介绍了数显表在我国的发展概况,以及感应同步器,光栅和磁栅兼容的数显表的基本原理。     

火花放电合成射流与超声速来流相互干扰特性数值模拟研究

为了指导火花放电式合成射流激励器在超声速流动控制中的应用,数值模拟研究了火花放电合成射流与超声速来流的相互干扰特性。研究表明火花放电式合成射流在超声速流场中产生强烈扰动,产生较强的激波结构;随着射流的喷出,激励器上游分离区和流场中激波呈先增强后减弱的趋势,激波由弓形激波逐渐弱化为斜激波,并且随着放电能量的增加射流与主流的动量通量比不断增大,射流的干扰和控制能力显著增强。由于超声速流的较大惯性及其对腔内气体的引射作用,激励器的腔体回填速率大幅下降、回填时间明显增长,使得激励器的工作频率受到很大限制。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

RTM用6818高温环氧树脂化学流变特性研究

以树脂传递模塑(RTM)用6818高温环氧树脂体系的化学流变特性研究为目的,以差示扫描量热法(DSC)和黏度实验为基础,采用外推法初步确定了6818树脂体系的固化工艺制度。依据双阿累尼乌斯方程建立了树脂体系的化学流变模型,模型曲线与实验数据的吻合性良好。模型分析表明,在80～100℃内树脂体系黏度低于200 mPa·s的时间大于12 h,可以作为6818树脂比较理想的注胶温度。该模型能够反映6818树脂黏度变化规律,预报该树脂体系的RTM工艺窗口。     

模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.