一种新的有限长等截面航空发动机短舱声学模型及数值结果

基于航空发动机短舱声学设计的需要,发展一种与以往工作不同的有限长管道声学模型声场的计算方法——直接边界元和传递单元法相结合。本方法对管道内部几何条件和声衬的敷设情况有更少的限制,可以很好地用于分段声衬的优化设计,并且提供求解有限长变截面管道声学模型的基础。     

潜入式喷管喉衬界面间隙优化设计

为了解决固体火箭发动机潜入式喷管喉衬在热载荷与内压联合作用下界面间隙优化问题,数值模拟方法求解了喷管热结构响应.采用流体仿真软件,计算了潜入式喷管流动过程的稳态流场,获取了高温燃气流动参数与固体壁面对流换热系数.并采用三维有限元结构计算平台,编写了非均布壁面压力载荷与非均布对流换热系数子程序,求解了喉衬前后搭接界面间隙...     

翼型测力天平的研制

为研究翼型结冰状态下的载荷变化规律,对翼型进行测力实验.研制一台三分量翼型测力天平.天平设计的突出难点为设计载荷极不匹配,阻力测量载荷很小.设计时,针对翼型载荷的特点,采用片梁组合方式测量阻力,四柱梁测量法向力及俯仰力矩,并采用有限元方法对结构进行了验证计算.主要介绍天平的设计、校准及应用情况.     

Investigation on Thermal and Dimensional Stability of Epoxy Resin In-Situ Modified by Cyanate Ester Resin and Polydimethylsiloxane

The thermal and dimensional stability of epoxy resin (EP) in-situ modified by cyanate ester (CE) and polydimethylsiloxane (PDMS) are investigated by means of experiments and numerical simulation. Thermal gravimetric analysis (TGA) and differential scanning calorimeter (DSC) are used to analyze the heat resistance of the modified EP. The dimensional stability is characterized by the volume shrinkage of the series PDMS/CE/EP obtained by the density method. The chemical structure of the PDMS/CE/EP is analyzed by Fourier transform infrared spectroscopy (FTIR). The results of TGA and DSC indicate that the thermal stability of PDMS/CE/EP decreases firstly and then increases with the increase in the amount of CE. The addition of PDMS shows a slight effect on the thermal stability. The 40% CE makes the blending system exhibit the lowest initial decomposition temperature, which reduces by 15.5% and 40.8% compared with pure EP and CE, respectively. The FTIR results suggested that the influence of CE on the thermal stability of the modified EP is mainly ascribed to the generation of oxazolidinone ring with low thermal stability and the increase in the triazine ring with high thermal stability. The volume shrinkage measurement results show that the introduction of CE and PDMS are both beneficial to the improvement of the dimensional stability of the blending systems. The in-situ addition of 80% CE shows the lowest volume shrinkage of 6.11%. The thermal stress distribution of PDMS/CE/EP generated during the solidification process is simulated by the finite element analysis. The results suggested that the introduction of 80% CE into EP results in the lowest thermal stress in the blending system, which indicates that the system has the lowest volume shrinkage, which agrees well with the experimental results.     

一种有效的基于DSmT的合成公式

针对DSmT在解决强冲突证据融合问题时存在的不足,提出了一种有效的冲突证据合成方法,即在保留冲突焦元的基础上对冲突量进行重新分配。仿真结果表明,新的合成公式提高了目标识别的可靠性与合理性,即使对于高度冲突的证据,也能够取得理想的合成结果。     

Ti-6Al-4V钛合金激光弯曲成形微观组织研究

以1mm厚Ti-6Al-4V合金薄板为对象,运用光学金相显微镜、电子探针、扫描电子显微镜、氮氢氧联合分析仪、显微维氏硬度计,研究了特定累积线能量下90°弯曲角弯折区显微组织。结果表明,弯折区组织与累积线能量输入有关,当累积线能量在适当范围时,材料堆积增厚,极表层出现轻微复熔铸态组织,上层为板条马氏体α′,中层为针状马氏体α′,底层为长大粗化的(α+β)组织;距表层约0.2mm范围吸收间隙元素强烈致使硬度急剧提高并呈明显梯度;累积线能量输入过大,弯折区出现大面积复熔铸态组织并伴有裂纹产生。     

多种材料人工脱粘应力场分析

采有网格自动生成技术，给出了考虑多种材料结构的人工脱粘层前缘附近推进剂／衬层界面较为合理的疏密平滑过渡的计算网格，对整个药柱尤其是对头部人工脱粘前缘附近进行了详细的有限元计算，得出了与实际情况接近的有限元诸模型析应力，应变场，此外，还考虑不同模量绝热层（人工脱粘层）和衬层对人工脱粘层前缘附近推进剂／衬层界面应力的影响。     

用非线性有限元法分析金属基复合材料的叠层板壳

采用通用于复合材料叠层厚、薄板壳的Ｈｅｆｅｒｏｓｉｓ三维退化曲壳元，利用Ｈｉｌｌ屈服准则和层状模型法，对金属基复合材料叠层板壳进行了弹塑性分析。算例结果表明，所用方法是可靠的，精度良好。     

卫星振动试验中推力的估算方法

准确预估规定试验条件下卫星振动试验所需推力对于试验的设计与实施具有重要意义。文章在常规卫星振动试验需用推力估算方法的基础上,结合具体的小卫星应用实例提出了支反力分析预示法和类比相似结构卫星推力的方法来估算卫星振动试验需用推力。通过与实际振动试验推力数据对比,文章给出了卫星振动试验需用推力估算方法的实用评估结论。     

缠绕复合材料喷管静力分析

本文对由一般曲线旋转得到的喷管进行了静力分析。文中讨论的喷管由缠绕复合材料构成,承受轴对称和非轴对称载荷作用。在采用有限元法分析时,通过Fourier转换将三维问题简化为二维求解。弹性矩阵中各参数采用合理假设只需由层状平面内三个弹性常数即可确定。文中给出缠绕复合材料喷管在内压和集中力作用下的位移分布算例,结果合理。本文推荐方法可供缠绕柔性喷管和其它类似结构分析时参考。