Active vibration control of piezoelectric bonded smart structures using PID algorithm

Thin-walled structures are sensitive to vibrate under even very small disturbances. In order to design a suitable controller for vibration suppression of thin-walled smart structures, an electro-mechanically coupled finite element(FE) model of smart structures is developed based on first-order shear deformation(FOSD) hypothesis. Considering the vibrations generated by various disturbances, which include free and forced vibrations, a PID control is implemented to damp both the free and forced vibrations. Additionally, an LQR optimal control is applied for comparison.The implemented control strategies are validated by a piezoelectric layered smart plate under various excitations.     

直升机复合材料桨叶固化过程的多物理场有限元模拟

根据热传导、复合材料力学和固化动力学理论,采用基于偏微分方程的强耦合多物理场有限元方

法,计算在F650 双马来酰亚胺树脂建议温度周期下直升机复合材料桨叶固化过程中温度、固化度、固化度反应

速率和内应力变化历程。通过仿真结果对温度周期进行优化调整,改善工艺过程。计算结果表明:桨叶中树脂

固化反应同步度高,交联反应产热量少;调整后的加热周期与建议加热周期相比,最高加热温度由460 K 降低

为393 K,但固化度由0. 1 增加到1 的反应时间只由25 min 增加为30 min,固化反应速率峰值从1. 35×10-3 / s

降低为1. 15×10-3 / s,PMI(聚甲基丙烯酰亚胺,Polymethacrylimide)泡沫的Von Mises 热应力最大值从0. 82 MPa

降低为0. 482 MPa。

     

高硬韧材料切削温度的解析预测

以传热学为基础，用有限差分数值方法，二元切削加工过程中切削区域温度场进行了计算机模拟，并以金刚石和硬质合金刀具切削钛合金炙例，进行了切削温度计算，经分析，计算结果与实测切削温度值吻合良好。这不但表明切削温度的计算机模拟可行的，同时人加工材料的切削加工特性提供了一种新的解析方法，可节省大量实验，为进一步预测最佳切削过程，指导新型刀具材料的开发奠定了基础。     

宇航电子设备中壳体的有限元分析

就宇航电子设备中壳体结构的建模进行了研究，采用板壳单元来描述结构，用局部刚化模拟壳体转角和加强处，并对壳体单元自由度和复要边界条件的处理作了大胆有益的探索。     

Composite control method for stabilizing spacecraft attitude in terms of Rodrigues parameters

In this paper, the attitude stabilization problem of a rigid spacecraft described by Rodrigues parameters is investigated via a composite control strategy, which combines a feedback control law designed by a finite time control technique with a feedforward compensator based on a linear disturbance observer (DOB) method. By choosing a suitable coordinate transformation, the spacecraft dynamics can be divided into three second-order subsystems. Each subsystem includes a certain part and an uncertain part. By using the finite time control technique, a continuous finite time controller is designed for the certain part. The uncertain part is considered to be a lumped disturbance, which is estimated by a DOB, and a corresponding feedforward design is then implemented to compensate the disturbance. Simulation results are employed to confirm the effectiveness of the proposed approach.     

Springback prediction of thick-walled high-strength titanium tube bending

Significant springback occurs after tube rotary-draw-bending （RDB）, especially for a high-strength Ti-3A1-2.5V tube （HSTT） due to its high ratio of yield strength to Young＇s modulus. The combination scheme of explicit and implicit is preferred to predict the springback. This simulation strategy includes several numerical parameters, such as element type, number of elements through thickness （NEL）, element size, etc. However, the influences of these parameters on spring- back prediction accuracy are not fully understood. Thus, taking the geometrical specification 9.525 mm × 0.508 mm ofa HSTT as the objective, the effects of numerical parameters on prediction accuracy and computation efficiency of springback simulation of HSTT RDB are investigated. The simulated springback results are compared with experimental ones. The main results are： （1） solid and continuum-shell elements predict the experimental results well; （2） for C3DSR elements, NEL of at least 3 is required to obtain reliable results and a relative error of 29% can occur as NEL is varied in the range of 1-3; （3） specifying damping factor typically works well in Abaqus/Emplicit simulation of springback and the springback results are sensitive to the magnitude of damping factor. In addition, the explanations of the effect rules are given and a guideline is added.     

微重力下球形贮箱内液体晃动有限元模拟

以卫星球形贮箱为研究对象,用任意拉格朗日-欧拉(ALE)法建立了数学模型,给出了计算的基本方程,并基于MSC-Dytran有限元程序,对常重力和微重力环境中贮箱内推进剂的晃动进行了数值模拟。结果表明,微重力环境中液体更易发生大幅晃动,甚至产生飞溅,工程中常用的等效力学模型已不再适用,而有限元数值模拟方法可较好地解决该问题,为卫星及大充液复杂结构航天器控制系统的设计和分析提供理论参考。     

推进剂贮箱锥柱形金属膜片的翻转特性研究

基于MSC.Marc非线性有限元软件,对推进剂贮箱锥柱形金属膜片的变形进行仿真研究。模拟了膜片的翻转变形过程,分析了膜片翻转变形规律和失效因素,提出了膜片有效稳定翻转的条件。     

液氧/甲烷发动机推力室多循环热-结构分析

为了研究一款液氧/甲烷发动机推力室多循环工作状态下的结构变形,拓展并验证了一种包括流动-传热分析和非线性有限元分析的热-结构分析方法。通过该方法得到了推力室热载荷与压力载荷分布,并分析了推力室在这些载荷下的应力应变响应。研究表明：推力室整体结构变形并非主要取决于热载荷,压力载荷引起的冷却通道底面弯曲在喷管扩张段尤其明显;后冷阶段产生的弹塑性拉伸应变大于热试阶段产生的压缩应变是导致每次循环结束后结构产生残余应变的直接原因;随着工作循环次数的增加,扩张段的冷却通道底角位置残余应变累积速率最快,该部位被确定为结构失效的潜在位置;增加冷却剂入口附近的通道底面厚度、减小后冷阶段与热试阶段的温差以及将冷却通道的尖锐底角设计为圆角可以成为抑制变形和减缓应变累积的备选措施。