FY-3(05)星主动对月定标控制技术研究

月球是低轨气象卫星载荷进行外定标的一个理想目标,不同载荷通过观测月球可以建立统一的参考基准,提高相互之间的数据匹配性.对于低轨卫星,月球一般每月一次进入载荷的视场,但停留时间只有几秒钟.为进一步提高对月定标的观测时长,积累更多的观测数据,本文针对低轨偏置动量卫星提出了一种主动对月定标控制方案,通过卫星平台的姿态控制,使...     

流星雷达系统相位差偏差的估计和校正

介绍了一种新的流星雷达系统的相位偏差估计和校正方法.利用流星回波的观测数据,用回波信号在各个接收通道之间的相位差,结合干涉式接收天线阵的几何关系,建立了各天线相位差测量值与偏差值之间的线性方程组,利用最小二乘法求解方程组,得到了流星雷达系统各个接收通道之间的相位差偏差估计值及校正后的流星回波到达角.与已有的流星雷达相位偏差估计和校正的方法相比,这种方法可以通过流星雷达的观测数据来计破算雷达系统各个接收天线通道之间的相位差偏差量,而不需要增加额外的硬件,实现了对观测数据的事后处理,可以方便地对已有数据进行校正.以2004年4-6月的武汉流星雷达观测数据为例,计算了流星雷达系统的偏差估计量,并用校正后的数据来计算流星回波的空间位置.结果表明,校正后流星回波数在各个方向上随高度的分布比校正前更符合统计分布.      

Novel attitude determination method by integration of electronic level meter,INS, and low-cost turntable for level attitude evaluation and calibration of INS

Attitude references are greatly needed for the evaluation and calibration of Inertial Navigation Systems (INSs), which are widely used in gravimeter, marine, and aeronautical navigation. High-accuracy turntable, INS, and Global Navigation Satellite System have been utilized to verify the performance of relatively low-accuracy INS. The accuracy requirement of the attitude reference continuously increases with the rapid improvement of inertial sensors and navigation algorithms. However, the cost of attitude determination system increases rapidly with the increase of attitude accuracy requirement. To solve this limitation, the integration of level meter, INS, and low-cost turntable is proposed to provide level attitude, such as roll and pitch. The turntable is utilized to rotate the INS. An integration model of the level meter and INS is built to estimate the level attitude and reduce the cost of the turntable. The proposed method successfully avoids the dependence on high-accuracy turntables. An observability degree analysis is conducted to improve the level attitude accuracy further. The simulation and turntable test results indicate that the proposed method can provide high-accuracy level attitude without high-accuracy INS or turntable and is applicable to error calibration and attitude evaluation of INS.     

用于EMI测量接收机脉冲响应校准的标准脉冲信号产生方法

EMI测量接收机作为电磁兼容测试中的关键仪器应用越来越广泛，但目前该类仪器的脉冲响应校准所用的标准源完全依赖于进口，国内尚无可替代的标准脉冲信号产生器。介绍一种用于EMI测量接收机脉冲响应校准的标准脉冲信号产生方法，首先建立标准脉冲信号的参数模型并对其进行数值分析和仿真，验证其符合CISPR 16-1-1标准的要求，之后搭建实验系统，利用标准脉冲信号生成软件控制任意脉冲信号发生器输出标准脉冲信号并对其进行补偿修正，获得符合CISPR 16-1-1标准要求的标准脉冲信号，该信号可用于EMI测量接收机脉冲响应的校准。     

TFM imaging of aeroengine casing ring forgings with curved surfaces using acoustic field threshold segmentation and vector coherence factor

The aeroengine casing ring forgings have complex cross-section shapes, when the conventional ultrasonic or phased array is applied to detect such curved surfaces, the inspection images always have low resolution and even artifacts due to the distortion of the wave beam. In this article, taking a type of aeroengine casing ring forging as an example, the Total Focusing Method (TFM) algorithms for curved surfaces are investigated. First, the Acoustic Field Threshold Segmentation (AFTS) algorithm is proposed to reduce background noise and data calculation. Furthermore, the Vector Coherence Factor (VCF) is adopted to improve the lateral resolution of the TFM imaging. Finally, a series of 0.8 mm diameter Side-Drilled Holes (SDHs) are machined below convex and concave surfaces of the specimen. The quantitative comparison of the detection images using the conventional TFM, AFTS-TFM, VCF-TFM, and AFTS-VCF-TFM is implemented in terms of data volume, imaging Signal-to-Noise Ratio (SNR), and defect echo width. The results show that compared with conventional TFM, the data volume of AFTS-VCF-TFM algorithm for convex and concave is decreased by 32.39% and 73.40%, respectively. Moreover, the average SNR of the AFTS-VCF-TFM is gained up to 40.0 dB, while the average 6 dB-drop echo width of defects is reduced to 0.74 mm.     

一种基于脉冲前导的数字相控阵距离校零方法

数字相控阵设备使用了高速AD、FPGA等大量数字器件，每次设备上电重启后，数字器件频率参考时钟的初始相位存在随机性，由此带来的时延抖动导致设备距离零值发生变化。在工程应用中，一般会在每次设备上电重启后实施一次系统校零，以确保测距零值的正确性，但这一处理无疑增加了系统工作的复杂性。提出了一种通过添加前导脉冲控制实现固定传输时延的方法，采用该方法后无需每次上电重复实施系统校零，简化了设备使用模式。仿真测试结果和工程实践验证了方法的有效性。     

落角与视场约束制导控制一体化策略

针对考虑视场(FOV)约束和落角约束的高超声速飞行器高精度打击问题，提出一种基于自适应动态规划(ADP)的新型制导控制一体化(IGC)策略。首先设计一种融合视场角与落角约束的视场角指令，在视场角精确跟踪的同时实现精确命中并满足两种约束，从而将约束问题转化为跟踪问题；然后，借助干扰观测技术估计制导控制一体化模型中不确定性并引入到性能指标设计中，又同时将视场角约束与落角约束考虑进去，设计基于自适应动态规划的制导控制一体化方法。利用ADP的强化学习思想求解出最优控制策略，既保证高超声速飞行器的精准打击，又满足视场角约束与落角约束，而且兼顾了对不确定性的鲁棒性。仿真结果验证了本文所提方法的有效性与优势。     

液体火箭发动机推力自动校准系统仿真

针对液体火箭发动机原位校准高准确度的要求,介绍了一种以伺服电机为执行部件,基于液压传动力值自动加载装置,阐述了该系统的结构和工作原理。建立系统数学模型,通过Matlab和AMEsim搭建了系统的仿真模型,在分析影响模拟推力加载准确度和稳定性的基础上,设计了模糊PID控制器。仿真结果表明:所设计的力值加载系统能够完成力值精确加载,(0~6)kN力值加载时间小于30 s,加载力的示值最大误差为±0.05%,满足校准力值加载需求。证明了在力值加载系统中引入模糊PID控制算法,可以有效补偿系统中的不确定性扰动,增强系统的鲁棒性。     

一种无引北三轴转台标定捷联惯组方法

用三轴转台标定捷联惯组时，需要对三轴转台引北，用于精准测量捷联惯组相对地球北向的角度。为了减少引北带来的繁重工作量，在研究传统六位置标定方法的基础上，设计了十二位置标定方法。给出了十二位置翻转编排，建立了捷联惯组器件误差参数模型，详细推导了求解误差参数的方程式，并在高精度三轴转台上进行了试验验证。结果表明，在对三轴转台无引北的情况下，十二位置标定方法仍能标定出捷联惯组的24个器件误差参数，且精度与六位置标定方法相当，达到了预期目的。     

星载微波辐射计的天线方向图校正和亮温计算

在简要介绍星载微波辐射计周期定标技术基础上,着重分析了外部周期定标技术,采用天线方向图校正技术进行了误差分析,对“冷”、“热”定标源进行了计算,提出了提高星载微波辐计定标精度的措施。