基于北斗三号导航系统的卫星定位技术

对北斗三号体制下的传输链路、接收门限进行理论分析,得出捕获算法采用4次非相干累加,可以使捕获灵敏度达到-130 dBm,同时实现定位时间小于5 min的综合较优结果.接着以低轨太阳同步轨道卫星为例,利用STK建模进行全轨道周期仿真,结果显示全程收星数超过4颗,定位精度达到2.59 m,速度误差为0.00378 m/s....     

Assessment of the suitability of public mobile data networks for aircraft telemetry and control purposes

This paper provides a review of the state of the art of relevant work on the use of public mobile data networks for aircraft telemetry and control proposes. Moreover, it describes the characterisation for airborne uses of the public mobile data communication systems known broadly as 3G. The motivation for this study was to explore how this mature public communication systems could be used for aviation purposes. An experimental system was fitted to a light aircraft to record communication latency, line speed, RF level, packet loss and cell tower identifier. Communications was established using internet protocols and connection was made to a local server. The aircraft was flown in both remote and populous areas at altitudes up to 8500 ft in a region located in South East Queensland, Australia. Results show that the average airborne RF levels are better than those on the ground by 21% and in the order of −77 dbm. Latencies were in the order of 500 ms (1/2 the latency of Iridium), an average download speed of 0.48 Mb/s, average uplink speed of 0.85 Mb/s, a packet of information loss of 6.5%. The maximum communication range was also observed to be 70 km from a single cell station. The paper also describes possible limitations and utility of using such communications architecture for both manned and unmanned aircraft systems.     

3D打印技术在水冷板加工中的应用研究

目前,3D打印技术在各行业得到了广泛的应用,探讨和研究3D打印技术在空空导弹中的应用具有重要的意义.简要介绍了3D打印技术概念、原理和材料,重点介绍了水冷板进行3D打印加工过程,打印成功的水冷板通过检验、加工、装配,满足结构设计要求.3D打印能够缩短水冷板加工周期,降低加工成本.     

基于80C31的手动测量装置CPM3板的 电路原理及故障处理

CPM3板是手动型测量机电控系统的核心部分，它具有一定的运动控制、采点计数以及自检功能。本文主要从调试和维修的角度探讨了CPM3板的电路设计原理，以及相应维修方法。     

State and disturbance estimation for test masses of drag-free satellites based on self-recurrent wavelet neural network

In recent years, the drag-free satellites have been widely used for some fundamental physical experiments, such as checking short-range effects of general relativity, geopotential determination and the exploration of static ocean current. And the space-borne detector of gravitational waves is one of the important applications for drag-free satellites in the future. In this study, the estimation of relative motion state and disturbance for test masses of drag-free satellite after release are researched. Firstly, the relative motion model between the test masses is established based on corresponding reference frames. Secondly, a self-recurrent wavelet neural network estimator is designed to estimate the pure gravitational relative motion state and disturbance for the test masses, and the sliding mode controller is used to transfer the relative motion state to the ideal state. Finally, the proposed estimation methods are verified by the simulation results.     

Extrinsic calibration of a laser displacement sensor in a non-contact coordinate measuring machine

In order to implement 3D scanning of those complicated parts such as blades in the aviation field,a non-contact optical measuring system is established in the paper,which integrates a laser displacement sensor,a probe head,the frame of a coordinate measuring machine (CMM),etc.As the output of the laser sensor directly obtained possesses the 1D length of the laser beam,it needs to determine the unit direction vector of the laser beam denoted as (l,m,n) by calibration so as to convert the 1D values into 3D coordinates of target points.Therefore,an extrinsic calibration method based on a standard sphere is proposed to accomplish this task in the paper.During the calibration procedure,the laser sensor moves along with the motion of the CMM and gathers the required data on the spherical surface.Then,both the output of the laser sensor and the grating readings of the CMM are substituted into the constraint equation of the spherical surface,in which an over-determined nonlinear equation group containing unknown parameters is established.For the purpose of solving the equation group,a method based on non-linear least squares optimization is put forward.Finally,the system after calibration is utilized to measure the diameter of a metallic sphere 10 times from different orientations to verify the calibration accuracy.In the experiment,the errors between the measured results and the true values are all smaller than 0.03 mm,which manifests the validity and practicality of the extrinsic calibration method presented in the paper.     

Modeling and Simulation of Pipeline Security Monitoring System Based on Line-Structure Sagnac Interferometer with 3×3Coupler

The third damage action,human disruption behavior,is one of the major threats to pipeline operation.It is necessary to monitor and locate the perturbation behavior that may threat pipeline safety in real-time.Therefore,a new pipeline security monitoring system is designed by using line-structure Sagnac optic fiber interferemeter with the characteristic of 3×3coupler that can modulate the phase of optic signal,with no need for phase modulation and demodulation.The optic structure of the new system is simplified,the signal processing accuracy is improved,and the polarization effect is reduced.The working principle of the monitoring in ideal condition is described,the phase demodulation is analyzed and the location of the possible damage action point is formulated.By using simulink,the optic signal propagation and interference is simulated and interference signals in different frequencies are obtained.The results validate the feasibility of the monitoring system and indicate that the low frequency signal less than 1kHz resulting from the human damage action can be detected.The disturbance set at 10 km can be located by calculating the demodulation signal accurately over a long monitoring distance.     

某航空发动机环形燃烧室CO和UHC的数值计算

采用FLUENT软件对某型航空发动机燃烧室在最大和地面慢车状态进行三维、两相、湍流燃烧模拟,计算了CO和UHC的生成,获得了温度场、速度场和浓度场的数值。CO和UHC主要在低工况下生成,但油气比对污染物排放影响较大。     

Disturbances in the ionospheric F-region peak heights in the American longitudinal sector during geomagnetic storms of September 2005

In this paper, we use the modified GSM TIP model to explore how the thermosphere–ionosphere system in the American longitudinal sector responded to the series of geomagnetic storms on September 9–14, 2005. Comparison of modeling results with experimental data at Millstone Hill, USA (42.6°N, 71.5°W), Ramey, Puerto Rico (18.3°N, 66.8°W) and Jicamarca, Peru (11.9°S, 76.9°W) has shown a good agreement of ionospheric disturbances in the F-region maximum height. We examine in detail the formation mechanisms of these disturbances at different latitudes and describe some of the important physical processes affecting the behavior of the F-region. In addition, we consider the propagation of thermospheric wind surge and the formation of additional layers in the low-latitude ionosphere during geomagnetic storms.