某型起动机起动故障的分析与研究

主要针对某型发动机地面起动时提前中止的状况进行理论分析,通过定位、排查,确定了故障原因,也为此类故障的排除提供了可行的方法。     

Design and numerical investigation of swirl recovery vanes for the Fokker 29 propeller

Swirl recovery vanes（SRVs） are a set of stationary vanes located downstream from a propeller, which may recover some of the residual swirl from the propeller, hoping for an improvement in both thrust and efficiency. The SRV concept design for a scaled version representing the Fokker 29 propeller is performed in this paper, which may give rise to a promotion in propulsive performance of this traditional propeller. Firstly the numerical strategy is validated from two aspects of global quantities and the local flow field of the propeller compared with experimental data, and then the exit flow together with the development of propeller wake is analyzed in detail.Three kinds of SRV are designed with multiple circular airfoils. The numerical results show that the swirl behind the propeller is recovered significantly with Model V3, which is characterized by the highest solidity along spanwise, for various working conditions, and the combination of rotor and vane produced 5.76% extra thrust at the design point. However, a lower efficiency is observed asking for a better vane design and the choice of a working point. The vane position is studied which shows that there is an optimum range for higher thrust and efficiency.     

Regional gravity field model in Pakistan area from the combination of CHAMP,GRACE and ground data using least squares collocation: A case study

This study describes a methodology of recovery of the Earth’s gravity field from CHAMP and GRACE satellites data in Pakistan using least squares collocation (LSC) based downward continuation technique. The CHAMP height anomalies and GRACE gravity disturbances derived from the observed satellite data have been used in combination solution using LSC with observed gravity values at the Earth surface. The combined covariance functions of height anomalies and/or gravity disturbances at satellite altitudes and observed gravity anomalies at Earth surface have been used as the basis for combination and downward continuation solution. The variance of predicted gravity anomalies from GRACE gravity disturbances is relatively lower than the corresponding results of gravity anomalies from CHAMP height anomalies. This fact may be attributed partly to the amplification of noise and partly to the unstable inverse transformation process of height anomalies to gravity anomalies. The impact of data error variance has been studied in the context of smoothing and noise reduction in the final solution of downward continuation using least squares collocation. The raising of data error suppresses the noise and as a result a smooth final solution is obtained. The prediction results appear to be dependent on the quality of data and goodness of combined covariance function, which are fairly comparable for the CHAMP and GRACE data. The recovered gravity field from satellite data appears to contribute mainly to medium and long wavelength parts of total gravity field spectrum. Due to flexibility of data handling in least squares collocation, this procedure is applicable to any observable of gravity field being at different altitudes and with different data spacing.     

一种双斜切双压缩面气道性能的数值模拟

采用LU－SGS隐式推进方法及ROE的通量差分分裂格式，结合带非线性限量因子的MUSCL插值方法编写了雷诺平均的三维N－S方程的数值求解程序，并供助该流场计算程序研究了一种双斜切双压缩面进气道在未经流场控制情况下的流动结构和气动性能（M＝1.9,H=11Km）。计算结果表明：所编制的流场计算程序能够准确快速地求解三维粘性流场，并对流场间断具有较高的分辨率；所研究的进气道即使在未经流场控制的情况下也具有较高的总压恢复系数，这体现了双斜切双压缩面进气道总压恢复系数高的优点，但由于流场中存在分离流动，应采取抽吸附面层等流场控制措施。     

叶轮流速系数对泵正反转性能参数比的影响

为研究叶轮流速系数对离心泵反转作液力透平(PAT)泵工况和透平工况水力性能参数比的影响,采用renormalization group(RNG) k-ε湍流模型,通过计算流体动力学软件CFX计算了比转速为23~225的20个PAT叶轮单流道模型的流速系数,揭示了泵工况和透平工况流速系数的分布规律,建立了考虑流速系数的PAT泵工况与透平工况扬程比和流量比。结果表明:PAT透平工况叶轮流速系数大于泵工况。通过对不同比转速的6台工业PAT的外特性实验表明:与Stepanoff等提出的方法相比,考虑流速系数时PAT水力性能参数比与实验结果最为接近,其扬程比平均误差为5.38%,流量比平均误差为5.16%。该成果为PAT的选型设计和性能预测提供理论支撑。      

一种波瓣混合器超级燃烧室的掺混特性

为了使涡轮基组合循环发动机超级燃烧室的涡扇涵道和冲压涵道两股气流具有高效低阻的掺混特性,设计了一种结构简单的方形波瓣混合器.用数值模拟方法对该方形波瓣混合器与常规混合器进行了比较分析,结果表明方形波瓣混合器具有与菊花型波瓣混合器相似的流向涡高效低阻掺混特性.进行混合器结构参数变化对掺混特性的影响研究发现扩张角对方形波瓣混合器的热混合效率的影响起主要作用,而出口高度的影响不大;当方形波瓣混合器的波长比为1.0时,方形波瓣混合器具有高效低阻的掺混特性.     

Numerical investigation of windage heating within shrouded rotor-stator cavity system with central inflow

The rotating disk surface temperature rise due to windage heating effect by numerically modeling the turbulent flow within a rotor-stator cavity which is available with a peripheral shroud and imposed through airflow was dealt with. The windage heating may be defined as viscous friction heating caused by relative velocity differences across the boundary layers between the fluid and the rotating disk surface. The kinetic energy dissipation process could transform the rotating shaft power into thermal heating. Commercial finite volume based solver, ANSYS/CFX was employed to numerically simulate this physical process by using the shear stress transport (SST) turbulence model. CFD results include the rotating disk surface temperature axial distribution and tangential velocity distribution of the fluid domain. The velocity difference between the result obtained by particle image velocimetry (PIV) experiments and CFD simulation are within 5%. The adiabatic disk temperature rise can be calculated by the tangential velocity of disk and fluid in large gap ratio and turbulent parameter. CFD temperature distribution results and those estimated via velocity differences are within 10%.     

中心锥对波瓣强迫混合排气系统气动热力性能的影响

在波瓣混合器几何结构不变的情况下,通过分别改变波瓣出口截面处中心锥半径以及波瓣长度建立了一系列几何模型,并采用数值模拟的方法,研究了中心锥关键结构参数对涡扇发动机波瓣混合排气系统气动热力性能的影响规律.结果表明:当中心锥长度不变时,随着波瓣出口处中心锥半径的增加,热混合效率先增加后减小,其中当波瓣出口处中心锥半径为0.55倍波瓣高度时,波瓣混合排气系统出口处热混合效率最大.此外,当中心锥长度不变时,波瓣混合排气系统总压恢复系数大体上不断减小;排气系统出口处推力系数则呈现出先增大后迅速减小.当波瓣出口处中心锥半径不变时,随着中心锥长度的增加,热混合效率和总压恢复系数变化极小,在排气系统出口处,推力系数则先迅速增大后略有降低.      

某民用大涵道比涡扇发动机风扇缩尺试验件气动性能数值仿真

根据某民用航空发动机大涵道比风扇1/2缩尺试验任务的需求,利用三维数值模拟软件对该风扇缩尺试验件各个转速下的内、外涵气动性能进行了数值仿真分析,并对缩尺几何、弹性恢复角及涵道比等参数对风扇缩尺试验件内、外涵气动性能的影响进行了对比分析.结果表明:该风扇缩尺试验件各转速下的内、外涵性能都基本达到设计指标;几何缩尺分别引起了风扇外涵、内涵设计点的效率分别降低了1.26%,0.77%;80%转速下,叶尖弹性恢复角减小0.36°使风扇外涵稳定工作裕度扩展了4.04%,但近设计点总压比和效率均有所衰减;双涵道风扇在不同涵道比状态下,内、外涵相互影响,流量-总压比及流量-绝热效率特性是在一定范围内的曲线带.      

大落差长度比中介机匣气动性能试验及数值模拟

为了考察中介机匣气动性能水平并验证设计方法,对中介机匣进行了气动性能试验,同时采用NUMECA Fine软件进行了相应的数值模拟。为了准确测量流过中介机匣内涵的气流流量,设计了一种流量测量装置并进行了精度校核,结果表明：测量精度的相对偏差小于1.5%。针对高进口马赫数时在进口平直段上两侧的壁面静压比中间区域小,以及某些涵道比未能调节到目标进口马赫数的情况,进行了相应的数值模拟并提出了解决方案。用单点总压管对内、外涵出口进行了扇面测量,得到了内涵的总性能曲线、总压恢复系数径向变化曲线及内、外涵总压恢复系数云图,并与计算结果进行对比,结果表明：内涵总性能曲线及内、外涵总压恢复系数云图的计算结果与试验结果吻合较好,在设计状态下,内、外涵出口测量截面的总压恢复系数分别为0.992 1、0.986,两数值均高于设计指标,中介机匣具有较好的气动性能。