高强中模碳纤维增强高耐热双马树脂复合材料性能

研究了一种耐高温改性双马来酰亚胺树脂（805）的工艺特性、流变特性和耐热性能,在此基础上制备了TG800/805国产高强中模碳纤维复合材料,并对高温及室温的力学性能和断裂微观形貌进行了表征。结果表明：805树脂的最低黏度为1.6 Pa·s,具有良好的工艺性;TG800/805复合材料具有优异的力学性能,经280 ℃热处理后,其弯曲强度和层间剪切强度在280 ℃的保持率分别为68%和52%,其玻璃化转变温度（T_g）为356 ℃,说明研制的TG800/805材料体系可以在280 ℃高温下较长时间使用。     

超细晶Laves相NbCr2颗粒增强Nb基复合材料的制备及其组织性能研究

采用机械合金化 热压工艺制备了Laves相NbCr2增强的Nb基复合材料。研究了Nb-22.5Cr配比成分的Nb,Cr元素粉经MA30h后在1250℃分别热压10min,20min和30min所获得的Nb/NbCr2复合材料的组织和性能。结果表明:三种热压时间均可制备出组织均匀,致密度高的Nb/NbCr2复合材料,体积分数约为30%的近等轴状的Laves相NbCr2颗粒弥散分布于Nb固溶体基体中。热压20min的试样具有最佳的组织和性能,其Laves相NbCr2的晶粒尺寸达到亚微米级,致密度达到99.2%,维氏硬度为9.41GPa,屈服强度为2950 MPa,抗压强度为3345 MPa,塑性应变达到了7.01%,充分实现了Laves相NbCr2颗粒强化和细晶强韧化的效果。     

Influence of welding parameters on microstructure and mechanical properties of electron beam welded Ti60 to GH3128 joint with a Cu interlayer

Effects of welding parameters on the microstructure and mechanical properties of Ti/Cu/Ni joint welded by electron beam were investigated. High welding heat input increased the melting quantity of Ti60 titanium alloy and promoted the formation of Ti–Cu intermetallic compounds (IMC) such as Ti₂Cu and Ti₃Cu₄, increasing the brittleness of the joints. Low welding heat input was not conducive to the complete melting of the copper interlayer, and the unmelted copper reduced the performance of the joints. Under the optimal welding parameters, Ti–Ni IMCs in the weld would be replaced by (Cu, Ni) solid solutions ((Cu, Ni)_ss). However, Ti–Cu IMC layers cannot be eliminated entirely by changing the welding parameters. The maximum tensile strength of the joints was 201 MPa. The fracture of the joints occurred at the Ti–Cu IMC layer, which was a typical brittle fracture.     

Influence of processing and external storage conditions on the performance of envelope materials for stratospheric airships

Envelope materials are extremely vital for stratospheric airships, which are widely used in numerous applications. The influence of processing as well as the storage and utilization conditions on the performance of envelope materials has been studied systematically for the first time. Results show that the performance of envelope materials depends largely on the hot-pressing temperature and the flexing during processing. The tensile strength of samples dropped to 289.1 ± 8.0 MPa from 346.6 ± 9.3 MPa when pressed at temperature above 180 °C and helium leakage appeared. The outer layers would be worn off when flexed no matter by manual or machine, resulting in dramatic increase of helium permeability and even leakage as well as varying decrease of mechanical properties. Hence, suitable hot-pressing temperature and limitation of flexing as little as possible during processing are essential to obtain products with suitable properties. Besides, the storage and utilization conditions are also critical to the properties of envelope materials. Both naturally aged samples in outdoor storage on ground and samples recovered from actual flight on stratospheric airship exhibited reduced mechanical properties and even helium leakage due to excess solar irradiation, ozone concentration and energetic particles interaction compared with those stored indoors. The weatherability of envelope materials should be further strengthened in the next few years. This research could provide a theoretical guidance for actual practice.     

Brazing of C/C composite and Ti-6Al-4V with graphene strengthened AgCuTi filler: Effects of graphene on wettability,microstructure and mechanical properties

Graphene nanosheets(GNSs) strengthened AgCuTi composite filler(AgCuTi_G) was used to braze C/C composite and Ti-6Al-4V. The effects of GNSs on the wettability of AgCuTi_G filler on the C/C composite surface and the interfacial microstructure and mechanical properties of brazed joints were investigated. The results indicate that the addition of GNSs reduced the wettability of AgCuTi_G. The interfacial microstructure of brazed joints evolved with the addition of GNSs, where Ti_3Cu_4 and TiCu_4 were converted to TiCu and the thickness of the reaction layer adjacent to the base material decreased. The maximum shear strength of joints brazed at 0.3 wt% GNSs was 23.3 MPa(880℃/10 min). Further adding GNSs deteriorated the shear strength of the joints. Fracture of the joints occurred in the C/C composite substrate and the TiC layer adjacent to C/C composite.     

C/C喉衬近净尺寸制备及性能

采用径向针刺工艺制备了近净尺寸针刺C/C喉衬预制体,通过热梯度CVI和树脂浸渍碳化复合工艺对预制体进行了致密,利用μ-CT、光学显微仪表征了C/C喉衬材料微观孔隙和热解碳织构,分析了喉衬材料的弯曲性能。结果表明,径向针刺过程形成的损伤型孔隙通道与碳源气体传输方向一致,提高了碳源气体传输效率,使径向针刺喉衬CVI增密效率比传统轴向针刺喉衬提高10.9%。预制体近净尺寸成型缩短了烧蚀区域碳源气体的渗透距离,喉衬材料烧蚀区域形成了高织构热解碳,有利于喉衬烧蚀性能的提高。径向针刺喉衬的轴向弯曲强度比轴向针刺喉衬提高150%。     

Estimation of sediment settling velocity in estuarine and coastal waters using optical remote sensing data

A robust method has been developed for estimating sediment settling velocity (w_s) from high resolution optical remote sensing data in estuarine, coastal and harbor waters. This method estimates settling velocity as a function of the drag coefficient (C_d), Reynolds number (Re), grain size (D₅₀), specific gravity (Δ_SG) and grain shape (in terms of the Corey Shape Factor – CSF). These parameters were derived from the particulate inherent optical properties such as backscattering (b_bp), beam attenuation (c_p), suspended sediment concentration and turbidity using Landsat 8 OLI and HICO data. Preliminary results for the Gulf of Cambay in the eastern Arabian Sea and Yangtze river estuary in the East China Sea, showed that satellite-retrieved settling velocities (m?s^?1) varied from very low values in clear oceanic waters, intermediate values in coastal waters, to very high values in river plumes and sediment-laden coastal waters. The remote sensing retrievals of sediment properties and their settling velocities were generally consistent with the field and laboratory results, which indicate that the proposed methodology will have important implications in various coastal engineering, environmental and management studies.     

某种叉流板翅式热交换器动态性能的计算

对某型飞机上应用的一种叉流板翅式热交换器的动态性能进行了计算研究,分别用数值计算方法和参数集中方法进行了计算,给出了计算比较的结果.结果表明,这2种方法计算所得的结果很接近,但是参数集中法计算程序更为简结,适合用于系统模拟的情况.      

激光选区熔化成形SiCP/AlSi10Mg复合材料工艺及性能研究

为研究激光选区熔化(SLM)成形技术制备SiC颗粒增强AlSi10Mg复合材料的成形机理,开展了SLM成形工艺参数(扫描间距、扫描速度)对致密度、机械性能等影响情况的研究。结果表明:所制备试样中SiC增强颗粒分布均匀,并与基体具有连续相容的冶金结合界面。当激光扫描速度从900 mm/s升高到2 100 mm/s时,在不同的扫描间距下,复合材料试样致密度均随之降低;当扫描间距在0.09～0.12 mm内变化时,在不同的扫描速度下,致密度变化趋势并不一致;在激光功率490 W、铺粉层厚0.04 mm、扫描间距0.12 mm、扫描速度900 mm/s时,制备的SiC颗粒增强AlSi10Mg复合材料试样得到最佳综合性能(相对密度99.1%,显微硬度198.7 HV0.2,抗拉强度341.9 MPa);在该最佳工艺参数下,成功制备出复杂结构的薄壁零件。研究为SLM成形SiCP/AlSi10Mg复合材料在航空航天和空间领域的应用提供了理论基础和实验依据。     

低温变形对2A14铝合金组织性能影响

提出了低温变形与热处理协同的2A14铝合金强韧化新方法,借助透射电镜、扫描电镜、金相显微镜、拉伸试验机等测试手段对比分析了室温和超低温变形工艺对2A14铝合金组织性能的影响。结果显示:与室温变形相比,超低温变形与热处理协同能够大幅提升合金综合力学性能。当超低温变形量达到20%,合金内部位错密度上升,第二相粒子尺寸更小,分布更为均匀,晶粒细化显著,合金综合力学性能达到最高,抗拉强度为474.5 MPa,屈服强度为426.5 MPa,延伸率为11.6%。