A debris image tracking using optical flow algorithm

This study proposes a motion detection and object tracking technique for GEO debris in a sequence of images. A couple of techniques (called the “stacking method” and “line-identifying technique”) were recently proposed to address the same problem. Although these techniques are effective at detecting the debris position and motion in the image sequences, there are some issues concerned with computational load and assumed debris motion. This study derives a method to estimate motion vectors of objects in image sequence and finally detect the debris locations by using a computer vision technique called an optical flow algorithm. The new method detects these parameters in low computational time in a serial manner, which implies that it has an advantage to track not only linear but also nonlinear motion of GEO debris more easily than the previous methods. The feasibility of the proposed methods is validated using real and synthesized image sequences which contain some typical debris motions.     

空间碎片现状与清理

分析了空间碎片的严峻现状和空间碎片的10个来源,指出轨道碰撞是产生碎片最多的因素;介绍了空间碎片的观测方法、原理和观测系统的概况,包括正在兴建的观测系统——“空间篱笆”。最后,根据不同轨道高度和空间碎片的数量与大小,提出空间碎片清理原则、要求和9种清理方法。     

基于四元数的UKF多传感器卫星姿态确定

对采用磁强计和太阳敏感器的卫星姿态模型,应用无迹卡尔曼滤波(UKF)算法确定卫星姿态。由四元数描述姿态,在算法中将其转换成旋转矢量,另设计了四元数求均值的迭代算法,解决了四元数在UKF算法中的处理。仿真结果表明:广义卡尔曼滤波(EKF)算法对初值依赖性较大,UKF算法不受初值影响且精度高于EKF,具快速性、精度高和稳定性强等优点。     

一种新型机载对地观测用三轴稳定平台陀螺安装方式

陀螺安装方式及相应的算法编排是稳定平台设计中的一项关键技术。针对机载对地观测用三轴稳定平台特点,提出了将方位陀螺安装在方位环上,俯仰陀螺和横滚陀螺安装在俯仰环上的陀螺安装方式。利用空间矢量分解理论分析了陀螺输出角速度信号的投影关系及电机控制信号的分配;基于稳定平台系统模型,对理想正交情况和考虑陀螺安装误差情况进行了仿真分析,验证了此种安装方式的可行性和优越性。分析表明,在同等条件下,所提出的安装方式减小了稳定平台的机械尺寸,降低了稳定平台的重量和功耗,实现了三维角速度的正交测量,简化了三轴解耦控制算法。研究结论可为其他三轴稳定平台结构设计和陀螺安装方式设计提供参考。     

Heliotropic dust rings for Earth climate engineering

This paper examines the concept of a Sun-pointing elliptical Earth ring comprised of dust grains to offset global warming. A new family of non-Keplerian periodic orbits, under the effects of solar radiation pressure and the Earth’s J₂ oblateness perturbation, is used to increase the lifetime of the passive cloud of particles and, thus, increase the efficiency of this geoengineering strategy. An analytical model is used to predict the orbit evolution of the dust ring due to solar-radiation pressure and the J₂ effect. The attenuation of the solar radiation can then be calculated from the ring model. In comparison to circular orbits, eccentric orbits yield a more stable environment for small grain sizes and therefore achieve higher efficiencies when the orbit decay of the material is considered. Moreover, the novel orbital dynamics experienced by high area-to-mass ratio objects, influenced by solar radiation pressure and the J₂ effect, ensure the ring will maintain a permanent heliotropic shape, with dust spending the largest portion of time on the Sun facing side of the orbit. It is envisaged that small dust grains can be released from a circular generator orbit with an initial impulse to enter an eccentric orbit with Sun-facing apogee. Finally, a lowest estimate of 1 × 10¹² kg of material is computed as the total mass required to offset the effects of global warming.     

Feasibility of performing space surveillance tasks with a proposed space-based optical architecture

Under ESA contract an industrial consortium including Aboa Space Research Oy (ASRO), the Astronomical Institute of the University of Bern (AIUB), and the Dutch National Aerospace Laboratory (NLR), proposed the observation concept, developed a suitable sensor architecture, and assessed the performance of a space-based optical (SBO) telescope in 2005. The goal of the SBO study was to analyse how the existing knowledge gap in the space debris population in the millimetre and centimetre regime may be closed by means of a passive optical instrument. The SBO instrument was requested to provide statistical information on the space debris population in terms of number of objects and size distribution. The SBO instrument was considered to be a cost-efficient with 20 cm aperture and 6° field-of-view and having flexible integration requirements. It should be possible to integrate the SBO instrument easily as a secondary payload on satellites launched into low-Earth orbits (LEO), or into geostationary orbit (GEO). Thus the selected mission concept only allowed for fix-mounted telescopes, and the pointing direction could be requested freely. Since 2007 ESA focuses space surveillance and tracking activities in the Space Situational Awareness (SSA) preparatory program. Ground-based radars and optical telescopes are studied for the build-up and maintenance of a catalogue of objects. In this paper we analyse how the proposed SBO architecture could contribute to the space surveillance tasks survey and tracking. We assume that the SBO instrumentation is placed into a circular sun-synchronous orbit at 800 km altitude. We discuss the observation conditions of objects at higher altitude, and select an orbit close to the terminator plane. A pointing of the sensor orthogonal to the orbital plane with optimal elevation slightly in positive direction (0° and +5°) is found optimal for accessing the entire GEO regime within one day, implying a very good coverage of controlled objects in GEO, too. Simulations using ESA’s Program for Radar and Optical Observation Forecasting (PROOF) in the version 2005 and a GEO reference population extracted from DISCOS revealed that the proposed pointing scenario provides low phase angles together with low angular velocities of the objects crossing the field-of-view. Radiometric simulations show that the optimal exposure time is 1–2 s, and that spherical objects in GEO with a diameter of below 1 m can be detected. The GEO population can be covered under proper illumination nearly completely, but seasonal drops of the coverage are possible. Subsequent observations of objects are on average at least every 1.5 days, not exceeding 3 days at maximum. A single observation arc spans 3° to 5° on average. Using a simulation environment that connects PROOF to AIUB’s program system CelMech we verify the consistency of the initial orbit determination for five selected test objects on subsequent days as a function of realistic astrometric noise levels. The initial orbit determination is possible. We define requirements for a correlator process essential for catalogue build-up and maintenance. Each single observation should provide an astrometric accuracy of at least 1”–1.5” so that the initially determined orbits are consistent within a few hundred kilometres for the semi-major axis, 0.01 for the eccentricity, and 0.1° for the inclination.     

CubeSail: A low cost CubeSat based solar sail demonstration mission

CubeSail is a nano-solar sail mission based on the 3U CubeSat standard, which is currently being designed and built at the Surrey Space Centre, University of Surrey. CubeSail will have a total mass of around 3 kg and will deploy a 5 × 5 m sail in low Earth orbit. The primary aim of the mission is to demonstrate the concept of solar sailing and end-of-life de-orbiting using the sail membrane as a drag-sail. The spacecraft will have a compact 3-axis stabilised attitude control system, which uses three magnetic torquers aligned with the spacecraft principle axis as well as a novel two-dimensional translation stage separating the spacecraft bus from the sail. CubeSail’s deployment mechanism consists of four novel booms and four-quadrant sail membranes. The proposed booms are made from tape-spring blades and will deploy the sail membrane from a 2U CubeSat standard structure. This paper presents a systems level overview of the CubeSat mission, focusing on the mission orbit and de-orbiting, in addition to the deployment, attitude control and the satellite bus.     

The effect of neglecting VLBI reference station clock offsets on UT1 estimates

Very Long Baseline Interferometry (VLBI) allows to monitor universal time (UT1) by conducting regular international experiments. Such dedicated observation networks are equipped with different hardware components, which require different processing strategies when the data are correlated. As the timing units at each stations are usually offset with respect to universal time (UTC) this effect should be considered during correlation processing. Thus, it is investigated how neglecting of these offsets theoretically impacts the estimation of UT1. Three different strategies for the proper handling of the timing offset will be discussed and their advantages/drawbacks will be pointed out. Moreover, it is studied how neglecting of these timing offsets affects UT1 time-series and how such a missing correction can be applied a posteriori. Although the discussed effect is for most of the UT1 experiments smaller than the formal error of the estimates, it is important to consider station clock offsets properly in next-generation VLBI systems, which are expected to improve accuracy of results by about one order of magnitude.     

Sumbandilasat—An operational technology demonstrator

Technology advances in sensor, digital technology and a standardised modular satellite bus are enabling a new generation of 80 kg micro-satellites with a better than 6.5 m GSD multi-spectral performance, to be specified, built and deployed with a dedicated launch within 12 months. The result of the standardised modular bus is lower cost, higher reliability and fast deployment. Operational remote sensing with a micro-satellite is thus within reach of individual organisations for dedicated missions. Sumbandilasat (pioneer in the Venda language) is a second generation satellite technology building on the expertise obtained in the Sunsat small satellite programme. The components used to build Sumbandilasat are the result of a technology development program of more than 3 years. Sumbandilasat is an operational technology demonstrator with more than 90% newly developed or improved subsystems and a compact refractive imager as a precursor to the MSMISat satellite with the same multi-spectral band set. The scalable, standardised modular satellite bus architecture enables satellites with a mass of 80–450 kg to be adapted to the specific mission requirements with minimum new engineering effort.     

基于圆球与椭球的地球敏感器地心矢量算法分析

红外成像敏感器代表了新一代敏感器的发展方向。本文介绍了红外成像敏感器光学系统工作原理,对红外成像敏感器光学系统进行简化,利用小孔模型完成了对敏感器光学系统的建模,分别在地球球形模型和旋转椭球模型下进行了地心矢量推导和计算,获得了焦平面内地平圆盘的相关参数的具体表达式,用牛顿迭代法对地心距进行数值计算,比较分析了球形模型与椭球模型在求解地心距精度上的差别,分析了敏感器测量误差对地心矢量精度的影响,以及焦平面内地平圆盘各参数分别对地心距计算精度的影响程度。