飞机生产中产生不协调问题的原因及解决办法

根据笔者多年来从事工艺技术的经验，总结了在飞机生产中，由于协调路线设计不合理、铆接装配变形、温度影响、在重量作用下引起的变形以及误差积累所产生的不协调问题，并结合具体的实例对上述不协调问题产生的原因提出了解决的办法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

参数曲线的自适应插补算法

参数曲线插补是高性能ＣＮＣ系统实现复杂轨迹控制功能的重要技术基础。文中提出了一种ＣＮＣ系统参数曲线的实时插补算法,基于参数预估、误差控制及参数校正的策略,实现了参数曲线的高精度快速插补。理论分析与仿真表明,该算法与现有的插补算法相比,不仅速度误差小、实时性好,而且插补速度能随曲线曲率的变化自适应调整,确保加工精度达到给定要求。此外,本算法具有良好的实现通用性,可以适用于样条等各种参数曲线。     

基于多元线性回归模型的光纤陀螺温度误差建模

在-40℃～60℃温度范围内测试了数字闭环光纤陀螺的标度因数、偏置和噪声,基于对测试 数据的分析指出,零偏稳定性大于0.3°／h的光纤陀螺的温 度误差主要来源于标度因数误差和偏置误差。利用逐步回归法分析了零偏与温度、温度梯度 之间的线性关系和标度因数与温度之间的线性关系,建立了零偏误差和标度因数误差的多元 线性回归模型。在模型中引入到达探测器的光功率作为新变量,提高了标度因数模型精度, 并使计算量减小40％。建模结果表明,标度因数误差回归模型的残差均方(RMS)达到1
(bit／(°／s)) 2,偏置误差回归模型的残差均方达到0.067(°／h) 2。     

弧齿锥齿轮啮合迹方向角的主动设计方法

为了实现弧齿锥齿轮设计规定的啮合迹方向,以局部综合法为基础,结合轮齿接触分析技术和无约束优化方法,进行弧齿锥齿轮啮合迹方向角的主动设计,给出了1种实现齿面参考点处啮合迹目标方向角的设计方法。通过1对弧齿锥齿轮的实例演示,论证了该方法对弧齿锥齿轮啮合迹方向角进行主动设计的可行性。结果表明:局部综合法中的输入啮合迹方向角必须小于旋转轴平面中规定的角度;在调整啮合迹方向角的过程中,传动误差曲线没有发生畸变。     

周向总压畸变对对转压气机影响效应分析

以对转压气机为研究对象,在数值方法校验的基础上,应用全通道定常流场分析手段计算了对转压气机不同周向畸变条件下的三维流场,获取了周向总压进气畸变对该压气机性能以及流场结构的影响效应,确定了对转压气机的临界畸变角,分析了不同畸变强度对压气机性能的影响规律,探讨了周向总压畸变在对转压气机中的发展演化过程。结果表明:(a)所研究的对转压气机临界畸变角约为72°,略高于传统动-静叶排交替的压气机临界畸变角;(b)相比均匀进气工况,当畸变指数为0.24时,对转压气机失速点压比和失速裕度分别下降3%和9.6%,当畸变指数为0.5时二者分别下降8.3%和19.8%;(c)未畸变区与畸变区流体之间存在的压力梯度影响转子叶片相对来流速度。进入畸变区叶片来流相对速度减小,负荷降低,退出畸变区叶片来流相对速度增大,负荷增大;(d)上游转子使得畸变水平提高,下游转子反向旋转效应抑制了来流相对速度变化趋势,增强了气流在其叶片通道中的掺混,使得畸变水平有所下降。     

多种失效模式相关的机构运动可靠度计算方法

机构运动中必然存在多种相关失效模式,多为影响机构运动的各类随机变量函数.为了在机构运动可靠性分析中有效考虑多种相关失效模式的影响,建立了考虑多种失效模式相关条件下的机构运动可靠度计算模型,并实现了对多种失效模式相关条件下的机构运动可靠度计算模型的求解,为考虑多种相关失效模式下的机构运动可靠性分析提供了一种有效途径.以6408滚动轴承为例,进行100 000抽样计算,考虑失效模式相关条件下运动可靠度为95.998 9%.该方法精度较高,具有一定的理论意义和应用价值.     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

反馈线性化飞行控制的应用问题研究

分析了反馈线性化飞行控制的奇异摄动降阶条件,讨论了外环解耦矩阵的奇异域和跟踪误差,建立了操纵面冗余时分配偏转指令的原则。用过失速转弯等机动进行了数值仿真验证。