蓄冰盘管冰层厚度测量及管外蓄冰性能实验

提出了一种新型简便的冰层厚度测量方法,该方法用测量冰层内温度分布的方法间接测量冰层动态厚度及冰层的相界面生长规律。对蓄冰盘管外结冰过程的实验研究表明,测量方法可靠,具有较高的测量精度;实验发现,蓄冰盘管外上部冰层生长较快,而下部冰层生长较慢,而在实验参数范围内管内乙二醇水溶液流量对冰层生长速度影响不大。     

"回收/调节"方法在混合LES/RANS模拟方法中的应用

采用一种混合大涡模拟/雷诺平均Navier-Stokes(LES/RANS)模拟方法结合三阶加权基本无振荡(WENO)格式对马赫数为2.88的压缩斜坡流动进行了数值模拟,并采用"回收/调节"方法生成入口湍流脉动边界条件.当采用固定入口边界条件时,湍流边界层会缺乏合理的湍流能量,使之抵抗逆压梯度的能力减弱,会严重高估分离...     

降雨对翼型气动性能影响的机理研究

利用计算流体力学软件FLUENT 6.3.26中的拉格朗日离散相模型研究了降雨条件下翼型的气动特性变化,并应用UDF(用户自定义函数)对FLUENT中自带的Wilcox转捩模式进行了修正,对降雨对翼型气动性能的影响机理进行了研究.结果表明,在降雨条件下,翼型表面积聚的水膜层及其表面粗糙度会影响翼型表面的光洁度,引起边界...     

Transitional wave configurations between Type III and Type IV oblique-shock/bow-shock interactions

The interactions of oblique/bow shock waves are the key flow phenomena restricting the design and aerothermodynamic performance of high-speed vehicles. Type III and Type IV Shock/Shock Interactions(SSIs) have been extensively investigated, as such interactions can induce abnormal aerodynamic heating problems in hypersonic flows of vehicles. The transition process between these two distinct types of shock/shock interactions remains unclear. In the present study, a subclass of shock/shock interaction configuration is revealed and defined as Type IIIa. Type IIIa interaction can induce much more severe aerodynamic heating than a Type IV interaction which was ever reported to be the most serious in literature. The intense aerodynamic heating observed in this configuration highlights a new design point for the thermal protection system of hypersonic vehicles. A secondary Mach interaction between shock waves in the supersonic flow path of a Type III configuration is demonstrated to be the primary mechanism for such a subclass of shock/shock interaction configuration.     

一种涡轮排气蜗壳的优化设计

为了改善涡轮排气蜗壳的排气效果,选取一种箱式蜗壳为原始计算模型,通过数值模拟研究了该排气蜗壳的气动性能,揭示了蜗壳内部流动损失的主要来源,在不改变其几何尺寸的前提下,提出了一种蜗壳的分流层改型设计,并与两种一般改型方式的效果作比较.数值计算结果表明:在设计工况下,分流层改型设计可使排气蜗壳的总压损失系数最多降低32.12%,静叶恢复系数最多提高48.73%,其效果好于扩压结构弧线改型,但弱于蜗壳壁面轮廓型线改型,在此基础上揭示了分流层设计改善蜗壳气动性能的机理.      

飞秒激光能量密度对镍基合金重铸层和加工效率的影响

以航空发动机叶片制孔为导向,结合飞秒激光对单晶镍基高温合金材料的非热熔性损伤阈值(Φth1)和热熔性损伤阈值(Φth2)特征,研究了飞秒激光能量密度(0Φ44.2J/cm2)对制孔重铸层和加工效率的影响规律。研究结果表明:在Φth1ΦΦth2时,镍基合金经飞秒激光加工后加工侧壁没有出现明显的重铸物;在ΦΦth2时,加工侧壁开始出现重铸物,并随着能量密度的增加,重铸层厚度增大。在试验结果的基础上,建立了飞秒激光单脉冲加工深度与能量密度的定量关系。能量密度越高,飞秒激光单脉冲加工深度越大,加工效率越高。     

超声速自由剪切层流动的数值模拟和理论分析

本文从二维完全Ｎ－Ｓ方程出发，采用ＮＮＤ２Ｍ差分格式，计算了超声速自由剪切层流场，并且研究了上游扰动在剪切层内的传播规律。在数值模拟的基础上对流动涡结构进行了分析。     

钛合金转子叶片系列焊机的研制及应用

针对各种新型航空发动机钛合金转子叶片阻尼台毗邻面耐磨性提高的迫切需求,研制成功JQGP-80型系列真空充氩高频感应钎焊设备,结合国产化材料及焊接工艺的全面突破,解决了钛合金叶片阻尼凸台磨损问题,为多种重点型号研制的顺利进行提供了强有力的硬件保障。     

超声速膨胀角入射激波/湍流边界层干扰直接数值模拟

为了揭示膨胀效应对激波/湍流边界层干扰区内复杂流动现象的影响规律,采用直接数值模拟方法对来流马赫数2.9、30°激波角的入射激波与10°膨胀角湍流边界层相互作用问题进行了数值研究。系统地探讨了激波入射点分别位于膨胀角上游、膨胀角角点和膨胀角下游3种工况下膨胀角干扰区内若干基本流动现象,如分离泡、物面压力脉动及激波非定常运动、湍流边界层统计特性和相干结构动力学过程等。结果表明,激波入射点流向位置改变对分离区流向和法向尺度的影响显著,尤其是当激波入射点位于角点及其下游区域。研究发现,膨胀角干扰区内物面压力脉动强度急剧减小,分离区内压力波向下游传播速度将降低而在膨胀区内将升高,膨胀效应极大地抑制了分离激波的低频振荡运动。相较于入射激波与平板湍流边界层干扰,入射激波流向位置改变对膨胀角再附区速度剖面对数区及尾迹区影响显著,将导致其内层结构参数升高而外层降低,近壁区内将呈现远离一组元湍流状态的趋势。此外,流向速度脉动场本征正交分解分析指出,主模态空间结构集中在分离激波及剪切层根部附近而高阶模态以边界层内小尺度正负交替脉动结构为主。低阶重构流场结果表明,前者对应为分离泡低频膨胀/收缩过程而后者表征为分离泡高频脉动。     

Percolation transition in temporal airport network

The air transportation system has a critical impact on the global economy. While the system reliability is essential for the operational management of air traffic, it remains challenging to understand the network reliability of the air transportation system. This paper focuses on how the global air traffic is integrated from local scale along with operational time. The integration process of air traffic into a temporally connected network is viewed as percolation process by increasing the integration time constantly. The critical integration time T_P which is found during the integration process can measure the global reliability of air traffic. The critical links at T_P are also identified, the delay of which will influence the global integration of the airport network. These findings may provide insights on the reliability management for the temporal airport network.