基于脉冲响应相关函数的模态辨识算法

利用不同时刻系统测量噪声具有独立同分布的特点,对脉冲响应进行相关处理,可以提高信噪比。为解决传统的基于脉冲响应的模态辨识算法的辨识精度问题,用某点脉冲响应同参考点响应之间的相关函数代替该点的脉冲响应以形成基于脉冲响应相关函数的模态辨识算法,并从理论上证明脉冲响应相关函数算法的辨识精度优于传统的脉冲响应算法。通过对一个四自由度系统模态频率和阻尼比的仿真辨识,验证了脉冲响应相关函数辨识算法的有效性。     

Orientations of LASCO Halo CMEs and their connection to the flux rope structure of interplanetary CMEs

Coronal mass ejections (CMEs) observed near the Sun via LASCO coronographic imaging are the most important solar drivers of geomagnetic storms. ICMEs, their interplanetary, near-Earth counterparts, can be detected in situ, for example, by the Wind and ACE spacecraft. An ICME usually exhibits a complex structure that very often includes a magnetic cloud (MC). They can be commonly modelled as magnetic flux ropes and there is observational evidence to expect that the orientation of a halo CME elongation corresponds to the orientation of the flux rope. In this study, we compare orientations of elongated CME halos and the corresponding MCs, measured by Wind and ACE spacecraft. We characterize the MC structures by using the Grad–Shafranov reconstruction technique and three MC fitting methods to obtain their axis directions. The CME tilt angles and MC fitted axis angles were compared without taking into account handedness of the underlying flux rope field and the polarity of its axial field. We report that for about 64% of CME–MC events, we found a good correspondence between the orientation angles implying that for the majority of interplanetary ejecta their orientations do not change significantly (less than 45 deg rotation) while travelling from the Sun to the near-Earth environment.     

Stochastic modelling considering ionospheric scintillation effects on GNSS relative and point positioning

Global Navigation Satellite Systems (GNSS), in particular the Global Positioning System (GPS), have been widely used for high accuracy geodetic positioning. The Least Squares functional models related to the GNSS observables have been more extensively studied than the corresponding stochastic models, given that the development of the latter is significantly more complex. As a result, a simplified stochastic model is often used in GNSS positioning, which assumes that all the GNSS observables are statistically independent and of the same quality, i.e. a similar variance is assigned indiscriminately to all of the measurements. However, the definition of the stochastic model may be approached from a more detailed perspective, considering specific effects affecting each observable individually, as for example the effects of ionospheric scintillation. These effects relate to phase and amplitude fluctuations in the satellites signals that occur due to diffraction on electron density irregularities in the ionosphere and are particularly relevant at equatorial and high latitude regions, especially during periods of high solar activity. As a consequence, degraded measurement quality and poorer positioning accuracy may result.     

基于三维裂纹尖端应力场的应力强度因子计算方法

提出一种基于无限大体裂纹尖端弹性应力场理论解的前几项多项式函数,对实际裂纹体弹性应力场有限元解进行拟合来计算应力强度因子的方法.该方法在计算应力强度因子时不需要预先假设裂纹尖端的应力应变状态,应力强度因子计算结果更符合三维裂纹体裂纹尖端实际的应力应变状态.首先基于二维无限大板中心穿透裂纹应力场理论解验证了方法的有效性,探讨了拟合确定应力强度因子需要的多项式应力函数的项数.然后分别以二维大板中心穿透裂纹、三维大体内埋圆裂纹和三维有限厚板中心穿透裂纹的应力强度因子计算为例,通过与无限大板和无限大体应力强度因子理论解以及基于位移外推法和1/4节点张开位移法的应力强度因子有限元解的对比分析,验证了该方法的有效性和合理性.研究表明该方法能够合理反映三维裂纹体裂纹尖端的实际应力应变状态,计算得到的应力强度因子数值更合理.      

复杂构件RTM整体成型工艺设计与仿真研究

以飞机预冷气引起口为典型构件,对其成型工艺进行探索,选择RTM成型工艺并应用PAM-RTM软件对RTM成型工艺影响参数进行虚拟仿真,确定模具设计的最终参数值.     

基于对偶四元数的捷联惯导算法在发射点惯性系下的应用研究

针对导弹类载体在做复杂的高动态机动时,采用传统的捷联惯导算法容易产生圆锥误差与划船误差,从而导致解算精度降低的问题,在发射点惯性系下设计了基于对偶四元数的捷联惯导算法.在建立发射点惯性系下的捷联惯导解算模型的基础上,详细推导了基于对偶四元数的捷联惯导解算算法,通过对比分析其中的速度更新过程与传统算法的差异,说明该算法可...     

微分对策理论及其研究现状分析

本文阐述了微分对策在经济和军事领域中的研究和应用,详尽地叙述了微分对策的分类,并采用定量和定性方法对微分对策进行了分析,指出了微分对策的研究难点,对发展趋势作了较为详细的探讨。     

关于平面激波在凹两段楔面上的传播

众所周知,当一平面激波同任意形状的障碍物相互作用时,将产生十分复杂的波系,其中激波在曲面壁上的绕射和反射,将产生非定常波系。关于平面激波在凹圆柱壁面上的传播,我们可以用一连串、长度为无限小的楔面所构成的多边形来近似和代替凹圆柱面,因此分析和研究激波在两段楔面上反射和绕射的目的在于得出激波在圆柱壁面以及其它较复杂形状壁面上的传播规律。本文采用马赫-曾德干涉仪在激波管上进行光测模型实验。根据所拍摄的流场干涉图像,以分析其波系的演变过程及传播规律,得到有关流场的密度分布和压力分布,更为重要的是给出流场参数的定量结果。     

非线性传感器静态特性评估的极限点法

基于对测量过程、测量误差的认识，提出了一种利用极限点法评估非线性传感器静态特性的一种新方法。给出了利用该方法评估非线性传感器的两种模型。并以一电涡流式非线性位移传感器的标定数据进行了计算、分析。     

遥测数据时间序列滑动窗口动态分割技术

经由传感器采集的航天器遥测数据是产品验证、算法检验、数据挖掘等学科和方向重要的数据来源之一。由于原始测量数据采集密度高、信息量大,通常采用滑动窗口技术进行逐段处理和算法应用。但当滑动窗口的宽度固定时,数据的局部信息不能被充分提取出来;为此,提出遥测时序滑动窗口的动态分割流程。仿真结果表明:提出的时序分割和窗口宽度计算方法,可以根据数据自身的特点得到更加准确合理的非等长窗口集合;在保持曲线线段曲率的基础上,滑动窗口动态计算方法可以极大地提取拐点信息,合理地给出窗口宽度,对数据进行了简化与提纯,降低了建模难度,为下一步聚类分析、曲线匹配等工作提供了技术支持,提高了遥测数据的诊断与分析效率。