Temporal evolution of the EIA along 95°E as obtained from GNSS TEC measurements and SAMI3 model

The total electron content (TEC) derived from GNSS measurements at a trans-hemispheric meridional chain of ground stations around 95°E longitude are used to study the quiet time inter-hemispheric structure and dynamics of the equatorial ionization anomaly (EIA) during the period March 2015 to February 2016. The stations are Dibrugarh (27.5°N, 95°E, 43° dip), Kohima (25.6°N, 94.1°E, 39° dip), Aizawl (23.7°N, 92.8°E, 36° dip), Port Blair (11.63°N, 92.71°E, 9° dip) and Cocos Islands (12.2°S, 96.8°E, 43° dip). The observation shows that the northern crest of the EIA lies in the south of 23°N (Aizawl) in all seasons but recedes further south towards the equator during December solstice. The largest poleward expansion of the northern (southern) EIA is observed in the March equinox (December solstice). The equinoctial and hemispherical asymmetry of TEC is noted. The winter anomaly is observed in the northern hemisphere but not in the southern hemisphere. The highest midday TEC over any station is observed in the March equinox. The TEC in southern summer (December solstice) is significantly higher than that in the northern summer (June solstice). The observed northern EIA contracts equatorward in the postsunset period of solstice but the southern EIA persists late into the midnight in the December solstice. The asymmetry may be attributed to the different geographic location of the magnetically conjugate stations. The SAMI3 simulations broadly capture the EIA structure and the inter-hemispheric asymmetry during solstices. The difference between observations and the SAMI3 is higher in March equinox and December solstice. The higher E?×?B vertical drift in the 90–100°E sector and the large geographic-geomagnetic offset in observing stations may have contributed to the observed differences.     

柔性薄壁结构电子束焊接的变形控制

基于电子束焊接方法,探讨了功率分出轴柔性薄壁结构真空电子束焊接过程中的变形控制方法,提出了综合应用最小焊接热输入、减小焊接重叠角度和合理焊接装配及散热相结合的变形控制方法,有效地控制了焊接变形,实现了电子束焊接柔性薄壁结构的制造。     

局域网网络操作系统选型的探讨

通过对NTServer4.0和NetWare4.11两大主流网络操作系统的分析、探讨,简述了网络操作系统选型的基本步骤、原则以及网络操作系统升级时应考虑的因素。     

基于高分四号数据的多时相多通道云检测算法

针对高分四号（GF-4）卫星影像波段较少导致传统云检测算法难以区分云与冰雪像元的问题,提出一种多时相多通道云检测算法。该算法首先对GF-4卫星影像进行辐射定标和配准,然后利用云与典型地表的光谱差异得到潜在云像元,之后利用序列GF-4卫星影像之间的差异识别出移动的云像元,最后利用中红外波段反演地表亮度温度来去除冰雪像元。该算法在海南、辽宁和安徽3个研究区域进行验证,并将检测结果与传统单时相云检测算法、支持向量机（SVM）云检测算法和实时差分（RTD）云检测算法的检测结果进行对比。结果表明,该算法优于其他3种云检测算法,准确识别率均达到90%以上,误检率均低于5%,有利于GF-4卫星影像的进一步利用。     

Evaluation of airborne data link communication

An experimental prototype of a cockpit data link communication interface (modified Navigation Display (ND) and Multi-purpose Control and Display Unit (MCDU)) was developed and tested in an Airbus A340 Full Flight Simulator. 8 crews (16 professional pilots) performed simulator flights in a mixed voice and data link scenario. After each experiment video recordings were presented to the pilots and they were asked to estimate subjective strain (NASA task load index) and situational aspects retrospectively. Results show an increase in subjective strain and a decrease of ‘feeling of sovereignty’ and situation awareness under data link conditions. The effect is similar to the one caused by higher workload.     

气氧/甲烷与气氢/气氧喷注器燃烧特性对比研究

为了获得气氧/甲烷与气氢/气氧两种推进剂组合燃烧特性的异同,将氢/氧气-气啧注器的设计经验用于气氧/甲烷气-气喷注器设计,在同一燃烧室中针对气氧/甲烷与气氢/气氧同轴剪切喷注器燃烧特性开展了数值仿真与试验研究.结果表明:在喷注器设计参数相似的情况下,气氧/甲烷喷注器尺寸与气氢/气氧喷注器尺寸相当;在相同的燃烧室设计压力、结构尺寸,以及两种推进剂组合均完全燃烧的情况下,要产生相同的推力,气氧/甲烷(混合比3.5)推进剂流量约为氢/氧(混合比6.0)推进剂流量的1.27倍,气氧/甲烷燃烧所需燃烧室特征长度约为氢/氧燃烧室特征长度的1.48倍,气氧/甲烷燃烧室壁面热载约为氢/氧燃烧室壁面热载的一半.     

一种航路4D航迹预测的方法

4D航迹预测是空管自动化系统中的一项核心技术,能够提高空域的利用率和安全性。为了在航路上快速准确的预测航空器的飞行轨迹,提出一种预测航路4D航迹的方法。首先利用Supermap制作航路网络,然后根据航空器的性能参数,推测各时间点的航空器位置,从而得到航路上航空器的飞行航迹,并通过实例进行了说明,为航迹预测提供一定参考。     

一种空间非合作目标的稀疏点云配准算法

点云数据配准是三维重构的关键技术之一,为了提高空间非合作目标的稀疏扫描点云数据配准的速度和精度,提出一种改进的基于四点算法的全局配准算法进行初始配准,再使用迭代最近点算法精确配准.针对直接扫描所得到点云数据量大的问题,本文提出一种基于KD Tree点云均匀采样简化算法,并且对传统基于四点算法中的阈值参数进行了统一,确定了各误差阈值参数和点云密度之间的关系.仿真结果表明,该方法能够快速、有效地实现卫星稀疏点云的配准,改进的四点算法配准耗时仅为几何哈希算法的42.49%.     

TC4-DT钛合金高温热变形行为研究

利用Gleeble-3500型热模拟实验机,研究了TC4-DT损伤容限型钛合金在温度850℃～1000℃、应变速率0.01～10s-1、变形程度为40%～70%条件下的热变形行为,分析了该合金的流变应力行为及微观组织演变规律,并建立了本构关系模型。研究结果表明,TC4-DT合金在950℃以下的较低温度变形时应力软化现象非常明显,变形机制和热变形激活能不同于950℃以上的较高温度变形机制;在950℃以上高温度变形时,低应变速率(如ε=0.01s-1)促进了动态再结晶行为的发生,而在较高的应变速率(如ε=10s-1)时,一般只发生动态回复现象,动态再结晶行为受抑制。     

Multi-objective output-feedback control for microsatellite attitude control: An LMI approach

Mixed H₂/H_∞ output-feedback controller with pole placement constraints against the internal uncertainty of moment-of-inertia variation and space environmental disturbances is proposed for mircosatellite attitude control. The multi-objective controller is designed based on linear model of attitude dynamics. The H_∞ performance takes into account both robustness stability against moments-of-inertia uncertainty and the disturbance rejection aspect. H₂ performance takes into account the LQG aspect which avoids the undesirable wheels’ saturation effect. In addition, the closed-loop poles can be forced into some sector of the stable half-plane to obtain well-damped transient responses. The problem is then reduced to a convex optimization involving linear matrix inequalities (LMIs), so it can be efficiently solved. The simulation results demonstrate that the presented mixed H₂/H_∞ control system is robust stable and optimal in the sense of H₂ norm, and has good steady-state and dynamic performances against the parameter uncertainties and various disturbances for the microsatellite attitude control system.