飞秒脉冲激光诱导TC4微结构表面抑冰特性实验

飞机发动机进气道前缘唇口积冰将会严重威胁航空安全,仿生研究表明具有微纳结构的疏水表面可以起到良好的抑冰效果。针对飞机唇口材料TC4,采用飞秒脉冲激光诱导制备TC4微结构表面,利用三维形貌仪和扫描电镜对TC4合金表面三维形貌和微纳结构进行观测,应用接触角测量仪分析表面浸润改性,依托结冰特性实验系统测试微结构表面抑冰抑霜性能,并分析飞秒脉冲激光加工工艺参数对表面微观结构和抑霜特性的影响机制。研究结果表明：随着激光扫描速度的增大,TC4合金表面形成的拱形沟壑深度增加,沟壑上方出现干涉条纹以及圆形凸起且微纳凸起的尺寸随扫描速度的增大而增大,接触角先减小后增大再减小;加工后表面液滴冻结时间比未加工表面延迟30 s;扫描速度2 000 mm/s时的液滴冻结时间最长,霜层质量最小,高度最低。飞秒激光加工TC4合金表面形成的微纳结构以及表面吸附的有机物能够改变表面接触角;粗糙度和表面形貌能够影响表面结冰时间和结霜量。     

一种高效低成本的视频压缩方法实现

文章提出了一种基于DSP的高效低成本的视频压缩方法的实现.硬件采用TI公司DM642 DSP,其具有成本低的特点,视频压缩采用MPEG4算法,实现复杂度适中,可高效满足用户需求.文章通过研究DSP的硬件架构,软件上采用调整程序结构、存储器优化、流水线技术、线性汇编等优化方法对移植成功的MPEG4 C语言程序进行优化.经测试,该系统优化前为2秒一帧,经优化后达到了标清25帧每秒的压缩任务,可满足军用或民用视频压缩领域的高效低成本应用需求.     

双轴模拟式太阳敏感器测试链误差分析及修正

基于四象限硅光电池,双轴模拟式太阳敏感器（简称双轴模太）可实现太阳矢量两轴方向角的同时测量。硅光电池各象限光生电流的采集精度直接决定了敏感器的工作性能。然而,测试链环节中存在的不一致性误差会引起双轴模太角度测量偏差。为此,基于数值仿真,分析并建立了硅光电池各象限响应率、各象限光生电流的电压转换、信号放大、A/D转换系数及暗电流等环节偏差的影响模型,进而对各环节的综合偏差进行标定和修正,从而在保证敏感器测量精度的同时,降低对测试链环节的要求。测试结果表明,在不改变测试链性能的情况下,双轴模太的测量精度由修正前的2.05° (α轴,3σ)和1.94° (β轴,3σ)提高到0.28° (α轴,3σ)和0.26° (β轴,3σ)。     

空间高能粒子与器件布线层核反应后次级粒子LET分布研究

空间高能质子和重离子是导致元器件发生单粒子效应的根本原因,为准确评估元器件在轨遭遇的单粒子效应风险,必须清楚高能质子、重离子与器件材料发生核反应的物理过程及生成的次级重离子LET（Line EnergyTransfer）分布规律。针对典型CMOS工艺器件模拟计算了不同能量质子和氦核粒子在器件灵敏单元内产生的反冲核、平均能量及线性能量转移值,并分析了半导体器件金属布线层中重金属对次级重离子LET分布的影响规律。计算结果表明：高能粒子与器件相互作用后产生大量次级重离子,且高能质子作用后产生的次级粒子的LET值主要分布为0～25MeV·cm²/mg;高能氦核粒子作用后产生的次级粒子的LET值主要分布为0～35 MeV·cm²/mg;有重金属钨（W）存在时能提高次级粒子的LET值,增加了半导体器件发生单粒子效应的概率,该研究结果可为元器件单粒子效应风险分析、航天器抗单粒子效应指标确定提供重要依据。     

Hot deformation behavior and microstructure evolution of the laser solid formed TC4 titanium alloy

Hot compressive experiments of the laser solid formed (LSFed) TC4 titanium alloy were conducted at a wide temperature range of 650–950 °C and strain rate of 0.01–10 s⁻¹. The Arrhenius-type constitutive models of the LSFed TC4 alloy were established at the temperature range of 800–950 °C and of 650–800 °C, respectively. The average relative error between the predicted stresses and experimental values in those two temperature ranges are 10.4% and 8.3%, respectively, indicating that the prediction models constructed in this paper are in a good agreement with experimental data. Processing maps were established by the principle of dynamic materials modeling on the basis of the data achieved from the hot compression experiments. The processing parameters corresponding to the stable and unstable regions of material deformation can be determined from the processing maps. The microstructure evolution of the stable and unstable regions of the samples after tests were observed. Finally, the effect of hot compressive parameters on the microstructure were investigated to research the dynamic recrystallization and the texture of the deformed LSFed TC4 alloy.     

钛合金TC4盘铣开槽加工铣削力研究

由于盘铣刀具直径大,切削余量大,造成钛合金盘铣开槽过程中铣削力较大,进而引起刀具振动,缩短刀具寿命。为实现对钛合金盘铣开槽过程的优化与控制,本文设计单因素实验和正交实验,利用三向压电式测力仪测量铣削力数据,采用线性回归技术建立铣削力模型并以“F”检验法对模型进行显著性检验;利用极差分析法分析工艺参数对铣削力的影响规律,利用响应曲面法分析工艺参数对铣削力的交互影响规律。研究结果表明：对于切削深度变化敏感度依次为铣削力F_x＞进给速度＞主轴转速;对于进给速度变化敏感度依次为铣削力F_y＞切削深度＞主轴转速;对于铣削力F_z变化敏感度依次为主轴转速＞切削深度。铣削力随着主轴转速的增大而减小,随着切削深度和进给速度的增大而增大。另外铣削力F_x大于F_y和F_z,对加工性能和刀具磨损起主导作用。     

Variation of hmF2 and NmF2 deduced from DPS-4 over Multan (Pakistan) and their comparisons with IRI-2012 & IRI-2016 during the deep solar minimum between cycles 23 & 24

We report the results of ionospheric measurements from DPS-4 installed at Multan (Geog coord. 30.18°N, 71.48°E, dip 47.4°). The variations in F2-layer maximum electron density NmF2 and its peak height hmF2 are studied during the deep solar minimum between cycles 23 & 24 i.e 2008–2009 with comparisons conducted with the International Reference Ionosphere (IRI) versions 2012 & 2016. We find that the hmF2 observations peak around the pre-sunrise and sunrise hours depending on the month. Seasonally, the daytime variation of NmF2 is higher in the Equinox and Summer, while daytime hmF2 are slightly higher in the Equinox and Winter. High values of hmF2 around midnight are caused by an increase of upward drifts produced by meridional winds. The ionosphere over Multan, which lies at the verge of low and mid latitude, is affected by both $E\times B$ drifts and thermospheric winds as evident from mid-night peaks and near-sunrise dips in hmF2. The results of the comparison of the observed NmF2 and hmF2 for the year 2008–2009 with the IRI-2012 (both NmF2 and hmF2) and IRI-2016 (only hmF2) estimates indicate that for NmF2, IRI-2012 with Consultative Committee International Radio (CCIR) option produces values in better agreement with observed data. Whereas, for hmF2, IRI-2016 with both International Union of Radio Science (URSI) and CCIR SHU-2015 options, predicts well for nighttime hours throughout the year. However, the IRI-2012 with CCIR option produces better agreement with data during daytime hours. Furthermore, IRI-2012 with CCIR option gives better results during Equinox months, whereas, IRI-2016 with both URSI and CCIR SHU-2015 options predict well for Winter and Summer.     

LOX/LCH_4变推力发动机技术初步研究

对国内外变推力发动机和LOX/LCH4发动机的研究进展进行了总结,在此基础上,提出了一种LOX/LCH4变推力发动机系统方案。在深入分析的基础上,对此方案进行了功率平衡和推力室传热计算,结果表明该系统方案完全能够实现10:1推力变比。LOX/LCH4变推力发动机可以广泛应用于多种运载器和航天器中,对我国探月及后续的载人登月工程均可以提供技术支持,对LOX/LCH4发动机的技术发展和未来的载人登陆火星等任务都具有深远影响。     

基于TCAD和Geant 4的SRAM单粒子效应评估

基于Geant4和TCAD (Technology-Computer Aided-Design)建立了一套评估静态存储器(SRAM)单粒子效应的方法. 该方法利用TCAD软件模拟半导体存储单元对粒子能量沉积的响应, 获得SRAM的重离子单粒子翻转截面, 并应用蒙特卡罗工具包Geant 4计算质子与硅材料的核反应以及次级粒子在灵敏体积内的能量沉积, 进而获得质子的单粒子翻转率. 利用该方法, 计算了TSMC 0.18 μm未加固SRAM的重离子和质子翻转率, 通过与同工艺SRAM的重离子实验结果进行比较, 初步验证了该方法的有效性. 该方法不依赖于地面模拟实验, 可以用来评估处于设计阶段的抗辐射加固器件.      

反向蒙特卡罗方法在卫星辐射分析中的研究与应用

反向蒙特卡罗方法(AMC/RMC)是Geant4中一个强有力的偏置技术. 粒子产生于包含灵敏体的反向界面并在几何体中被反向追踪直至外界面或溢出能量阈值, 其计算时间只集中于对结果有贡献的粒子径迹. 与正向蒙特卡罗方法(FMC)相比, RMC更高效, 特别是当灵敏体远小于几何体其他部分和外界面时, 其优势更明显. 通过RMC与FMC的比较, 验证了RMC应用于卫星辐射剂量分析的准确性. RMC与SHIELDOSE2和SSAT的比较说明了RMC是高精度卫星辐射剂量的优选方法.