低轨卫星编队飞行的地面覆盖及轨道调整

通过施加冲量的方法消除J2项摄动和大气阻力摄动对编队飞行的影响,在编队的相对构型和整体绝对位置得到控制后,研究了低轨卫星编队飞行的地面覆盖问题,最后通过算例给出了卫星编队在南北纬86°之间全球覆盖所需的时间、周期、圈数和覆盖角。计算结果表明,对于偏心率较小的低轨编队飞行,根据本文所推导公式计算出的结果是比较可靠的。     

推力矢量发动机燃气舵舵间干扰的数值分析

通过求解N-S方程,对某空空导弹燃气舵在不同状况下的三维湍流干扰流场进行数值仿真,得到了燃气舵在不同舵偏角下绕流流场的复杂波系结构,计算了测量舵在无干扰舵和有干扰舵情况下升力和阻力等参量随舵偏角的变化曲线。所得舵间干扰相对误差不超过2%,与实际要求相吻合。结果表明,所采用的流动模型和数值模拟方法对燃气舵的气动性能进行预示是有效的。     

火箭靶弹零升阻力系数辨识

火箭靶弹无控飞行过程中飞行攻角较小且无法准确模拟,为提高靶弹弹道理论预估精度,弹道理论计算可假定飞行攻角为零,将飞行攻角产生的诱导阻力贡献折算为对零升阻力系数的修正。建立了火箭靶弹气动特性工程计算方法,针对火箭靶弹零升阻力系数计算模型不确定性问题,利用火箭靶弹A飞行试验GPS遥测数据对其零升阻力系数进行了参数辨识,基于辨识结果对火箭靶弹零升阻力系数工程计算方法进行了修正。经火箭靶弹B飞行试验结果验证,由于综合考虑了飞行攻角产生的诱导阻力贡献,采用修正后的零升阻力系数,弹道理论预估精度大大提高,满足工程要求。     

基于大气阻力实时辨识的Drag-free卫星最优控制研究

研究了基于大气阻力实时辨识的Drag-free卫星最优控制。将Drag-free卫星和其内部的验证质量等效为两颗内、外编队卫星并建立动力学方程,推导了基于卫星和验证质量的相对运动状态观测值反演大气阻力的算法。建立了状态最优调节器模型,采用动态规划求解经典的二次型最优控制。对低轨圆轨道Drag-free卫星的仿真计算结果表明方法的求解精度较高,计算消耗较小。     

水气动量交换的实验研究

在风浪槽中进行水气动量交换实验，测量了不同风速和风区下的波浪及空气湍流流场。测量数据表明水面上风速分布符合对数律，水气界面附近在小范围的动量交换常通量层。阻力系数ＣＤ随风速增加线性增长，随波龄增加而减小。这一趋向与理论分析及外海帝测结果一致。对风浪发展过程中波浪和空气湍流谱结构的分析证明了水气运动的耦合关系。     

Refining DORIS atmospheric drag estimation in preparation of ITRF2008

In preparation of ITRF2008, all geodetic technique services (VLBI, SLR, GPS and DORIS) are generating new solutions based on combination of individual analysis centers solutions. These data reprocessing are based on a selection of models, parameterization and estimation strategy unique to each analysis center and to each technique. While a good agreement can be found for models between groups, thanks to the existence of the IERS conventions, a great diversity still exist for parameter estimation, allowing possible future improvements in this direction. The goal of this study is to focus on the atmospheric drag estimation used to generate the new DORIS/IGN ignwd08 time series prepared for ITRF2008. We develop here a method to inter-compare different processing strategies. In a first step, by analyzing single-satellite solutions for a few weeks of data but for a large number of possible analysis strategies, we demonstrate that estimating drag coefficient more frequently (typically every 1–2 h instead of previously every 4–8 h) for the lowest DORIS satellites (SPOTs and Envisat) provides better geodetic results for station coordinates and polar motion. This new processing strategy also solved earlier problem found when processing DORIS data during intense geomagnetic events, such as geomagnetic storms. Differences between drag estimation strategies can mostly be found during these few specific periods of extreme geomagnetic activity (few days per year). In such a case, when drag coefficient is only estimated every 6 h or less often for single-satellite solution, a significant degradation in station coordinate accuracy can be observed (120 mm vs. 20 mm) and significant biases arose in polar motion estimation (5 mas vs. 0.3 mas). In a second step, we reprocessed a full year of DORIS data (2003) in a standard multi-satellite mode. We were able to provide statistics on a more reliable data set and to strengthen these conclusions. Our proposed DORIS analysis is easy to implement in all software packages and is now already used by several analysis centers of the International DORIS Service (IDS) when submitting reprocessed solutions for ITRF2008.     

Aerothermodynamic and stability analyses of a deployable re-entry capsule

Recent research projects, in the field of atmospheric re-entry technology, are focused on the design of deployable, umbrella-like Thermal Protection Systems (TPSs). These TPSs are made of flexible high temperature resistant fabrics, folded at launch and deployed in space for de-orbit and re-entry operations. In the present paper two possible sphere–cone configurations for the TPS have been investigated from an aerodynamic point of view. The analyzed configurations are characterized by the same reentry mass and maximum diameter, but have different half-cone angles (45° and 60°). The analyses involve both the evaluation of thermal and aerodynamic loads and the assessment of the capsule longitudinal stability. The aerothermodynamic analysis has been performed for the completely deployed heat shield in transitional and continuum regimes, while the longitudinal stability has been analyzed in free molecular, transitional and continuum regimes, also taking into consideration the heat shield deployment sequence at high altitudes.     

Reconfigurable Flight Control Design for Combat Flying Wing with Multiple Control Surfaces

With control using redundant multiple control surface arrangement and large-deflection drag rudders,a combat flying wing has a higher probability for control surface failures.Therefore,its flight control system must be able to reconfigure after such failures.Considering three types of typical control surface failures(lock-in-place(LIP),loss-of-effectiveness(LOE) and float),flight control reconfiguration characteristic and capability of such aircraft types are analyzed.Because of the control surface redundancy,the aircraft using the dynamic inversion flight control law already has a control allocation block.In this paper,its flight control configuration during the above failures is achieved by modifying this block.It is shown that such a reconfigurable flight control design is valid,through numerical simulations of flight attitude control task.Results indicate that,in the circumstances of control surface failures with limited degree and the degradation of the flying quality level,a combat flying wing adopting this flight control reconfiguration approach based on control allocation could guarantee its flight safety and perform some flight combat missions.     

Viscoelastic behaviour of pumpkin balloons

The lobes of the NASA ULDB pumpkin-shaped super-pressure balloons are made of a thin polymeric film that shows considerable time-dependent behaviour. A nonlinear viscoelastic model based on experimental measurements has been recently established for this film. This paper presents a simulation of the viscoelastic behaviour of ULDB balloons with the finite element software ABAQUS. First, the standard viscoelastic modelling capabilities available in ABAQUS are examined, but are found of limited accuracy even for the case of simple uniaxial creep tests on ULDB films. Then, a nonlinear viscoelastic constitutive model is implemented by means of a user-defined subroutine. This approach is verified by means of biaxial creep experiments on pressurized cylinders and is found to be accurate provided that the film anisotropy is also included in the model. A preliminary set of predictions for a single lobe of a ULDB is presented at the end of the paper. It indicates that time-dependent effects in a balloon structure can lead to significant stress redistribution and large increases in the transverse strains in the lobes.     

Optimization of entry-vehicle shapes during conceptual design

During the conceptual design of a re-entry vehicle, the vehicle shape and geometry can be varied and its impact on performance can be evaluated. In this study, the shape optimization of two classes of vehicles has been studied: a capsule and a winged vehicle. Their aerodynamic characteristics were analyzed using local-inclination methods, automatically selected per vehicle segment. Entry trajectories down to Mach 3 were calculated assuming trimmed conditions. For the winged vehicle, which has both a body flap and elevons, a guidance algorithm to track a reference heat-rate was used. Multi-objective particle swarm optimization was used to optimize the shape using objectives related to mass, volume and range. The optimizations show a large variation in vehicle performance over the explored parameter space. Areas of very strong non-linearity are observed in the direct neighborhood of the two-dimensional Pareto fronts. This indicates the need for robust exploration of the influence of vehicle shapes on system performance during engineering trade-offs, which are performed during conceptual design. A number of important aspects of the influence of vehicle behavior on the Pareto fronts are observed and discussed. There is a nearly complete convergence to narrow-wing solutions for the winged vehicle. Also, it is found that imposing pitch-stability for the winged vehicle at all angles of attack results in vehicle shapes which require upward control surface deflections during the majority of the entry.