动力对全机水滴收集率的影响计算

针对飞机在飞行中遭遇过冷水滴撞击并结冰现象,建立了适合于发动机带动力情况下结冰过程水滴收集率计算的三维数值方法和计算程序.其基本思路为:采用多块技术与SIMPLE方法计算空气流场,以流场分布的计算结果为基础,求解水滴相的控制方程,进而获得物体表面的水滴收集率.空气相控制方程和水滴相控制方程均写成典型输运方程的形式,采用一致的有限体积法离散求解,方便了计算程序的编制.对某型运输机巡航构型有/无动力条件的水滴收集率进行了比较计算,获得了不同直径水滴在飞机表面的撞击特征以及水滴收集率在飞机机翼、平尾、垂尾和发动机进气道唇口上的分布规律.研究表明:(1)发动机是否带动力对机翼、平尾、垂尾的水滴收集率基本无影响;(2)飞机带动力主要影响发动机进气道唇口处的水滴收集率,带动力后唇口的收集率比无动力情况高,水滴撞击范围增大,在进行防除冰研究和设计时需引起重视.     

Understanding Substorms in the Magnetotail: Early Development and Recent Progress

This is a concise review of physics of the substorm in the magnetotail. It consists of two parts. The first part summarizes historical developments in the early days of the space age (1960--1975) when the basic concepts such as magnetotail and reconnection were established and the leading model of the substorm was introduced. The second part is an overview of the research conducted in recent years (1995--2010) when very significant advances have been achieved in understanding the substorm physics by virtue of several major satellites missions that addressed the magnetotail physics intensively.      

基于恒应变率控制的椭圆凹模胀形试验方法

为确定2A16-O铝合金板材在不同温度及应变率下的成形极限曲线(FLCs),应用改进Hollomon公式获取满足外插可靠度的拟合应力应变,通过有限元分析(FEA)不同椭圆度的椭圆凹模胀形破裂位置,优化工艺参数得到指定应变路径下的成形极限点,建立了液体压力与等效应变及应变率的公式,推导出压力变化率与应变率的定量关系。以应变率控制的椭圆凹模胀形与单拉试验相结合,获得2A16-O铝合金板材在不同温度及应变率下的FLCs,为定量分析应变率的影响规律和评判理论预测方法的准确性提供了依据。      

电脉冲除冰系统参数的合理选择

目前,尽管可采用各种防(除)冰方法,但它们在需用能量及除冰性能上尚有不足之处。电脉冲除冰所需能量少、维护方便(无运动部件)、可靠性高、重量小及经济性好等方面大大优于现有的其他防(除)冰系统。本文介绍了电脉冲除冰系统的基本工作原理,分析了能量,电容和电压等电气参数、线圈的几何参数及蒙皮的材料等对除冰性能的影响。根据分析和实验室、冰风洞及飞行实验的资料,提出了有效除冰时各种參数的选择范围,以及提高性能的措施。     

紧凑热交换器优化设计

对各种传热表面的板翅式紧凑热交换器进行了优化设计计算，建立了通用优化程序系统。此程序既适用于一般地面热交换器，也适用于飞机空调中的热交换器。与传统的设计计算相比较，优化设计的效果很好。热交换优化后，肋片的形状变得更加合理，芯体传热表面更加紧。通过各种肋片的计算得出，条状肋片为板翅式肋片中的最佳者。     

流动显示的现状和发展

本文以第四届国际流动显示会议为主要内容,结合其它资料介绍流动显示的现状和发展。     

Relationship Between Substorm Auroras and Processes in the Near-Earth Magnetotail

Although the auroral substorm has been long regarded as a manifestation of the magnetospheric substorm, a direct relation of active auroras to certain magnetospheric processes is still debatable. To investigate the relationship, we combine the data of the UV imager onboard the Polar satellite with plasma and magnetic field measurements by the Geotail spacecraft. The poleward edge of the auroral bulge, as determined from the images obtained at the LHBL passband, is found to be conjugated with the region where the oppositely directed fast plasma flows observed in the near-Earth plasma sheet during substorms are generated. We conclude that the auroras forming the bulge are due to the near-Earth reconnection process. This implies that the magnetic flux through the auroral bulge is equal to the flux dissipated in the magnetotail during the substorm. Comparison of the magnetic flux through the auroral bulge with the magnetic flux accumulated in the tail lobe during the growth phase shows that these parameters have the comparable values. This is a clear evidence of the loading–unloading scheme of substorm development. It is shown that the area of the auroral bulge developing during substorm is proportional to the total (magnetic plus plasma) pressure decrease in the magnetotail. These findings stress the importance of auroral bulge observations for monitoring of substorm intensity in terms of the magnetic flux and energy dissipation.     

旋转整流罩积冰过程中水膜流动和脱离的数值研究

为了更准确地模拟旋转整流罩积冰过程,在现有三维积冰与冰层表面薄水膜流动耦合模型基础上,基于功平衡分析的方法引入了旋转部件表面水膜脱离模型,并发展了相应的计算方法,给出了水膜脱离的判定依据:当气流曳力做的功和由于离心力使水膜增加的潜能之和大于黏附功时整流罩表面的水膜会发生脱离。对旋转整流罩积冰进行数值模拟,计算结果与实验结果吻合得较好,验证了该模型的合理性和计算方法的可行性。之后分析了转速和来流速度对整流罩表面水膜脱离和积冰的影响,结果表明:转速和来流速度越大,水膜发生脱离的比例越大。在研究范围内,转速为3000r/min和6000r/min时,因水膜脱离导致积冰总量分别减少13.4%和15.8%;来流速度为40、50m/s和60m/s时,因水膜脱离导致积冰总量分别减少为12.2%、13.4%、14.2%。      

弹片热机械疲劳试验方法研究及设计

针对弹片的热机械疲劳（TMF）试验要求,采用机械设计技术、机电技术、冷却技术、计算机技术和数据采集技术,提出了压力载荷和热载荷的加载方法,建立了2种载荷5个试验件的并联试验控制系统,并设计了弹片热机械疲劳试验器。试验结果表明:该系统能够同时模拟服役环境下弹片的压力载荷和热载荷。利用该试验系统进行了弹片的热机械疲劳试验,试验结果再现了弹片在服役状态下的失效模式。试验系统具有良好的重复度、较高的加载频率和加载精度。压力载荷最大相对误差为2.4%,绝对误差小于0.5N。温度载荷最大相对误差为3.55%,最大绝对误差为3.89℃。