叶轮机非定常气动设计的缘线匹配(II)数值研究

缘线匹配通过考虑多叶排叶轮机相邻叶排间前排叶片尾缘线与后排叶片前缘线空间相对位置匹配关系来进一步提升叶轮机性能,有潜力使叶轮机非定常设计走向工程实际。以一单级跨声轴流压气机和一单级轴流透平为例,尝试用基元流动展向积分方法和全优化方法改善其性能,从而示例应用缘线匹配的具体方法及前景。结果表明,缘线匹配为叶轮机非定常设计提供了可操作的自由度。     

推力向量控制方案及计算

本文归纳推力向量控制的主要方案,着重介绍摆动喷管、流体二次喷射方案的计算思路和结果.摆动喷管中的流场计算要考虑导弹偏摆对所产生的惯性力的影响;所得壁面压力畸变图说明,它是一个三维流场.在摆动喷管设计中要将铰链力减至最小,流体二次喷射的侧向力通过“等效实体模型”,用爆炸波的解来计算.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

亚声速叶片与跨声速叶片的气动阻尼比较

为了研究叶轮机中叶片与流场流固耦合作用情况下的气动阻尼,分别以亚声速和跨声速转子叶片为例计算气动阻尼。根据对非定常气动力的分析,提出了一种与结构等效粘滞阻尼比对应的模态气动等效粘滞阻尼比的定义。采用弱耦合分域求解的算法,在线性范围内,计算并比较了跨声速叶片和亚声速叶片模态和振幅对模态气动阻尼比的影响,根据分布气动阻尼比研究压缩波对模态气动阻尼比的影响。研究结果表明这两类叶片的气动阻尼特性基本一致,所提参数对两类叶片的气动阻尼的影响基本相同。     

叶轮机械颤振稳定性的工程预测方法

通过求解雷诺平均N-S方程并采用影响系数法,对三个基本正交模态的三维振荡涡轮叶片绕流问题进行了研究。结果表明数值模拟所得非定常气动力与实验吻合较好;基于刚体运动假设和模态叠加法,得到了可用于叶轮机械设计阶段颤振稳定性评估的稳定性参数图/气动阻尼图,即所有可能的刚体运动及其相应气动阻尼的关系图;通过对稳定性参数图/气动阻尼图的分析表明,在一定情况下振型对颤振稳定性有重要影响,应将其作为颤振稳定性设计的重要参数之一。     

冲压发动机气膜冷却分析模型

本文建立了冲压发动机燃烧室气膜冷却传热分析程序。根据燃烧室设计的技术要求,从冷却性能角度完成气膜冷却系统的气动性能和传热特性分析,提供冷却结构优化所需的信息。     

用极大似然法辨识轴对称飞行器的气动参数

采用极大似然法完成了轴对称飞行器的非线性气动参数辨识。根据飞行弹道的特性,采用考虑了横侧向运动耦合的纵向三自由度飞行动力学模型;为了反映气动参数随马赫数的变化,给出了一种考虑马赫数变化的气动参数数学模型,并采用了分段辨识的技巧;通过采用建模前估计法的辨识结果作为极大似然法的初值,保证了极大似然法的收敛,计算结果表明：这种算法对大攻角下的非线性气动参数能获得满意的辨识结果。