航空动压式油气分离器分离性能的实验研究

为了研究航空发动机动压式油气分离器的分离性能,采用容积法判别分离效率,并以此为据对结构形式、筒体直径及长度、入口管倾斜角和出气管长度等因素对分离性能的影响进行了研究。结果表明:采用内置式出气管与切向出油管相结合的形式,可使分离性能达到最佳;实验工况范围内,大的筒体直径更易于油气分离;入口管倾斜角存在最佳值,其值在10°~15°;当出气管长度取0.2~0.22倍分离器长度时,分离性能最佳;分离器长度过长会降低分离性能,实验条件下选5倍筒体直径为宜。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于微观结构分析的CMDB推进剂动态断裂韧性加载率敏感性研究

为研究改性双基推进剂(CMDB)的动态断裂特性,利用霍普金森实验技术(SHPB)对CMDB推进剂进行了冲击实验,并对实验数据的可靠性进行了校验;通过数值仿真的方法进一步验证了实验数据的有效性,获得了CMDB推进剂的动态断裂韧性;利用电镜扫描技术对试件断面进行了微观表征和分析。结果表明:CMDB推进剂在加载率58906~100056MPa·m1/2·s-1范围内,表现出明显的加载率敏感性;加载率达到105000 MPa·m1/2·s-1左右时,断裂韧性不再继续增大,反而出现下降趋势;电镜分析结果表明,CMDB推进剂加载率敏感性与其内部高氯酸铵(AP)颗粒的微观破坏机理直接相关。     

考虑泄漏间隙有压流体作用的指尖密封瞬态性能分析

针对已有指尖密封性能分析工作中未考虑泄漏间隙有压流体作用使得指尖密封的理论分析与工程实际有较明显差距的问题,建立了考虑泄漏间隙中有压流体作用的指尖密封性能分析模型,对是否考虑泄漏间隙中有压流体作用的指尖密封性能差异进行了比较分析.研究结果表明:指尖密封性能分析工作需要考虑泄漏间隙有压流体的作用.考虑泄漏间隙有压流体作用指尖密封的泄漏率较不考虑有压流体作用的泄漏率最大增加了234.7%,且有压流体作用使指尖密封泄漏率随转速增加的趋势更加显著.      

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.      

基于Kriging模型的轴承结构参数优化设计方法

轴承的生热率与轴承的使用寿命密切相关,为了减小轴承的生热率,以滚动轴承拟静力学分析和滚道控制理论为基础,求得轴承运转过程中的相关参数,进而得到轴承生热率.将轴承最小生热率为目标函数,通过Kriging模型和粒子群优化算法相结合的方式进行了轴承结构参数优化.对NSK 7016A5轴承的研究结果表明:轴承结构参数优化后,轴承整体和轴承内外圈生热率均变小.Kriging模型和粒子群优化算法相结合的轴承结构参数优化方法取得了良好的设计效果,并且提高了轴承的设计效率.      

基于响应面法的短距/垂直起降飞机近地面升力损失

建立了短距/垂直起降(S/VTOL)飞机近地面升力损失的流场计算模型.通过数值模拟得出特定升力布局的飞机近地面状态各工况的升力损失.采用响应面法获得了飞机升力损失关于喷管落压比（NPR）、来流速度及飞机高度的2阶响应曲面函数及显著影响飞机升力损失的关键因素.并分析了喷管落压比、来流速度及飞机高度对飞机升力损失的交互影响作用,优化得出给定工况范围内升力损失最小的工作点.研究表明:仅考虑单因素影响时,升力损失随高度、落压比的增大而减小,随来流速度的增大而增大;考虑两因素交互作用时,高度与落压比及来流速度与落压比对升力损失存在交互影响,而高度与来流速度对升力损失无交互影响;优化获得的升力损失最小的工作点是飞机距地面高度为9D（D为喷管直径）、喷飞机高度为3、来流速度为0m/s,此时的升力损失为1.3%.      

Z-pins增强陶瓷基复合材料层间Ⅰ型开裂性能预测

基于Z-pins增强陶瓷基复合材料层间Ⅰ型断裂韧性的试验结果、Z-pins增强机理,提出了Z-pins拔出的单线性软化模型.重点考虑了Z-pins直径范围内拔出位移的不一致性,在简单双悬臂梁（DCB）理论的基础上,获得了Z-pins增强陶瓷基复合材料层间Ⅰ型开裂性能的分析预测模型,预测结果与试验结果吻合较好.在此基础上,采用预测模型获得了不同Z-pins直径、裂纹长度下的裂尖能量释放率,并与理想弹簧元法进行了比较.结果表明:当裂尖靠近Z-pins时,随着Z-pins直径增大,两种方法所得的裂尖能释放率的差异逐渐增大,但总体来说差异的量级很小;随着裂纹长度的增加,裂尖逐渐远离Z-pins,两种方法所得的裂尖能释放率的存在较大的差异,不能忽略Z-pins直径范围内拔出位移不一的影响.