面向未知区域深度测量的序列图像稠密点特征生成算法

对未知着降区平坦度测量是无人机在复杂地形下安全着陆的关键问题。首先,根据小孔成像原理推导出基于单目序列图像的未知区域深度计算方程;其次,针对稀疏匹配存在深度信息重构误差大而稠密匹配在平滑区域误匹配率高的问题,提出一种基于Delaunay三角剖分的稠密点特征生成算法;然后,分别对序列图像中的2帧图像提取亚像素级Harris角点和尺度不变特征变换(SIFT)特征点,并分别进行特征点匹配;再以2种特征点间的欧氏距离作为约束条件将2种特征点进行融合,生成准稠密特征点;最后,将准稠密特征点进行Delaunay三角剖分,并根据每个剖分三角形上3个顶点像素偏差的方差值制定稠密特征点的生成策略,并结合所提出的深度计算方程计算整个未知区域各点的深度信息。通过Vega Prime(VP)搭建仿真演示验证系统,实验结果表明在机载相机距地面400m处计算高度分别为90m和55m的物体深度信息时,其深度测量相对误差不超过0.89%,具有较高的精度。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

无网格法耦合RNG k-ε湍流模型在亚、跨声速翼型黏性绕流中的数值模拟

基于移动最小二乘无网格方法,耦合RNG(Re-Normalisation Group)k-ε湍流模型求解雷诺平均Navier-Stokes方程。采用AUSM(Advection Upstream Splitting Method)+-up迎风格式求解数值通量,应用在高度各向异性点云结构中取得良好结果的点云重构技术结合移动最小二乘法拟合空间导数,并用三阶SSP(Strong Stability Preserving)型Runge-Kutta显式时间推进格式求解离散后的控制方程。在此基础之上,实现了对NACA0012、RAE2822翼型亚、跨声速黏性绕流的数值模拟,给出了翼型表面压力系数分布曲线、不同位置处的平均速度剖面、马赫数等值线等计算结果,并与实验值及相关文献数值模拟结果进行比较,结果吻合较好。表明所发展的结合点云重构技术的无网格方法耦合RNGk-ε湍流模型能够成功模拟翼型亚、跨声速黏性绕流,验证了所提算法的有效性,并拓展了无网格方法求解湍流流动的途径。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

无线电高度表信号模拟器射频信号延时/衰减模块设计

无线电高度表程控信号模拟器是无线电高度表自动测试系统（ATE,ATS）的重要组成部分,而射频信号延时/衰减模块则是无线电高度表程控信号模拟器3个功能模块组件中的核心模块。研制了一种采用声表面波（SAW）延迟线作为射频信号延时器件、射频衰减器作为射频信号功率衰减器件,通过程控射频开关控制不同声表面波延迟线的切换,包含射频信号变频、放大等结构电路的无线电高度表信号模拟器射频信号延时/衰减模块。经无线电高度表自动测试系统的实际工程应用表明,该无线电高度表射频信号延时/衰减模块对C波段（4.2～4.4 GHz）射频调制信号的延时精度高、衰减范围大,体小、质轻,适合置于无线电高度表测试适配器内部使用,具有较高的工程应用价值。     

基于定位特征点的叶片锥束CT点云模型配准方法

针对实际生产过程中锥束CT检测空心涡轮叶片的点云数据与计算机辅助设计模型的配准问题,提出了一种基于定位特征点的叶片锥束CT点云模型配准方法。首先将点云数据与计算机辅助设计模型进行预配准;然后查找空心涡轮叶片的设计定位特征点坐标;最后根据定位基准点寻找点云数据上与之对应的基准点,并建立各自坐标系,根据坐标系进行几何变换,迭代直至满足要求,从而完成精确配准。试验结果表明,该方法很好地实现了锥束CT点云模型的配准定位,满足了实际生产要求。     

基于EFFD方法的自然层流短舱优化设计

采用extended free-form deformation(EFFD)方法研究了自然层流(natural laminar flow,NLF)短舱的气动外形优化设计方法.使用基于Bernstein基函数的EFFD方法完成了NLF短舱剖面的参数化,利用基于k-εSST(shear stress transport)两方程湍流模型的γ-θ转捩模型进行自然转捩预测,结合EFFD、一种混合动网格方法、Kriging代理模型和改进的粒子群算法(particle swarm optimization,PSO)建立了针对NLF短舱气动外形的优化设计框架.采用该框架分别对通气NLF短舱和带动力NLF短舱进行优化设计.单独通气NLF短舱优化结果的外表面实现48%的层流,阻力系数比初始通气NLF短舱减小了0.0003.带动力NLF短舱的优化结果外表面保持了41%的层流.这些结果表明采用相关技术建立的优化设计框架在NLF短舱设计中具有一定应用价值.     

7075铝合金在不同温度盐水环境中的腐蚀疲劳行为

基于飞机结构材料7075铝合金在沿海地区服役时海水飞溅及曝晒导致的高温腐蚀疲劳损伤问题,研究了7075铝合金在35,55,75℃下3.5%NaCl溶液环境中的腐蚀疲劳寿命,并使用扫描电子显微镜(SEM)观察断口形貌,探讨了温度对腐蚀疲劳裂纹萌生扩展的影响机理。结果表明:同一应力水平下,温度越高,腐蚀疲劳寿命越短,300MPa时35,55,75℃下的中值寿命分别为33 001,30 931,15 346次循环。腐蚀损伤和疲劳损伤存在竞争关系,应力水平较高时,腐蚀较轻,试样寿命主要受应力水平影响,疲劳源多从铝合金基体与包铝层结合处萌生;应力水平较低时,腐蚀较严重,疲劳寿命随温度升高明显下降,疲劳源多从腐蚀坑处萌生。断口形貌显示高温环境主要通过加速腐蚀坑的形成来影响疲劳源的萌生,深坑状腐蚀坑应力集中严重,对疲劳性能伤害大。