QD-×××燃气轮机验证机台架试车的性能研究

QD-×××燃气轮机是由某型发动机改造成的燃气轮机,试车过程中解决了验证机起动、稳定工作并达到燃气轮机设计要求。试验数据表明:发动机改进设计后实测输出功率小于发动机设计计算功率,经过分析得出,验证机排气温度高,内涵空气流量小,是验证机输出功率小的根本原因。     

"十一五"期间企业开展"三大规范"的设想

探讨了"十一五"期间"三大规范"的编制和贯彻工作,提出重点内容建议,并对"三大规范"编制和贯彻工作的创新拓展进行了探讨.     

典型二元高超声速进气道设计方法研究

综合了一系列典型二元高超声速进气道的设计和性能估算方法, 给出了可行的设计原则.在满足流量、增压以及工作范围(起动性能和反压承受能力)的条件下, 给出了进气道进口、外压波系、内压缩通道、唇罩及隔离段的设计方法.采用此方法, 以H=22800 m、Ma0=6为设计点, 完成了一高超声速进气道的初步设计, 并估算得到了进气道性能参数、进气道的起动马赫数和反压承受能力, 对比CFD计算结果, 误差不大.通过该方法得到的进气道具有结构简单、流量系数大、压缩损失小的特点, 不通过优化即可得到性能较为良好的模型.      

冲击体质量和冲击高度对里氏硬度测量值影响的分析

利用正交试验的方法分析了冲击体质量和冲击高度对里氏硬度测量值的影响,同时给出了一个两因素水平的可允许变动范围.     

VSPWorks程序设计技术

VSPWorks是应用于多DSP并行系统的嵌入式实时操作系统,其先进的程序设计思想,大大简化了传统多DSP系统的软件开发模型,既保证了软件质量,也提高了开发效率.在详细介绍了虚拟单处理器模型和系统启动过程的基础上,讨论了应用程序开发过程,并举例介绍了网络连接文件的编写方法.     

机载大屏幕显示器的余度设计及余度管理

余度技术是系统或设备获得高可靠性的设计方法之一。为了显著提高系统的任务可靠性,当系统发生故障时,余度系统能够自动完成系统重构,继续正常工作,从而提高了飞机的任务可靠性和安全性。本文从余度设计的概念出发,通过对余度等级、结构、数目及层次等几个方面对余度设计进行分析,结合某大屏幕显示器余度设计,给出了余度设计的基本方法,提出了一种余度管理方案,该设计思想也可用于其它机载设备中。     

改进的Qiu滑移因子模型用于离心压气机叶轮的参数研究

为适用于微型离心压气机叶轮的通流设计,对Qiu滑移因子模型加入了3个经验参数.首先对经验参数的求解方法及参数对于设计精度的影响进行了分析研究,发现其中经验参数c_r对于设计精度影响较大.其次在通流设计中应用改进的Qiu滑移因子模型辅助生成叶片,用计算流体动力学(CFD)研究了c_r所影响的模型滑移因子,与数值流场的出口平均滑移因子对比,得到了多种叶轮总体参数下c_r的最佳取值.发现虽然微型、大型离心压气机叶轮总体参数变化范围很大,但c_r的取值均以0.7左右为其最佳值.      

加力燃油计量装置的AMESim 仿真研究

为获得加力燃油系统数字化仿真与性能验证平台,采用功能划分的方法分析了典型计量装置的功能模块,确定了伺服阀-随动活塞、计量活门-等压差活门是决定计量装置动态特性的主要组成部分,对其进行了数学建模。鉴于获得的数学模型描述系统特性时缺乏相关元件特性参数的设计依据,建立了由计量活门、等压差活门、电液伺服单元等组成计量装置的AMESim模型,计算主要结构参数后仿真分析了其稳态和动态特性。结果表明:基于控制系统构成的加力燃油计量装置功能划分与数学建模可为仿真研究与参数设计提供指导,AMESim可用于动态过程仿真与性能预测。     

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.