全文获取类型
收费全文 | 653篇 |
免费 | 105篇 |
国内免费 | 62篇 |
专业分类
航空 | 632篇 |
航天技术 | 52篇 |
综合类 | 68篇 |
航天 | 68篇 |
出版年
2024年 | 4篇 |
2023年 | 25篇 |
2022年 | 37篇 |
2021年 | 25篇 |
2020年 | 27篇 |
2019年 | 32篇 |
2018年 | 28篇 |
2017年 | 35篇 |
2016年 | 35篇 |
2015年 | 29篇 |
2014年 | 35篇 |
2013年 | 41篇 |
2012年 | 48篇 |
2011年 | 41篇 |
2010年 | 35篇 |
2009年 | 39篇 |
2008年 | 41篇 |
2007年 | 34篇 |
2006年 | 31篇 |
2005年 | 32篇 |
2004年 | 19篇 |
2003年 | 17篇 |
2002年 | 20篇 |
2001年 | 10篇 |
2000年 | 15篇 |
1999年 | 14篇 |
1998年 | 13篇 |
1997年 | 10篇 |
1996年 | 7篇 |
1995年 | 4篇 |
1994年 | 5篇 |
1993年 | 10篇 |
1992年 | 6篇 |
1991年 | 4篇 |
1990年 | 4篇 |
1989年 | 4篇 |
1988年 | 1篇 |
1986年 | 1篇 |
1984年 | 1篇 |
1983年 | 1篇 |
排序方式: 共有820条查询结果,搜索用时 125 毫秒
61.
钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜(SEM)、能谱(EDS)、X射线衍射(XRD)、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明:低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。 相似文献
62.
This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing's total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing's maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing's total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred. 相似文献
63.
64.
65.
66.
67.
针对变截面结构产品,提出了一种变截面搭接结构搅拌摩擦焊接方法,通过加装辅助板将整条焊缝焊接方向上补偿为等厚度。焊接采用一次定位焊接+二次定位焊接+正式焊接的工艺方式,一次定位焊为预定位,二次定位焊保证辅助板与试片主体结构之间形成有效连接,正式焊保证形成完整的焊缝。焊缝表面成形良好,超声相控阵检测无超标缺陷。通过对力学性能的分析,变截面搭接结构处焊缝与非搭接处焊缝和常规对接焊缝的力学性能基本相同,平均抗拉强度均达到母材的70%以上,平均延伸率均在5.8%以上。变截面搭接焊缝焊核处晶粒形态为细小的等轴晶,靠近轴肩影响区部分的晶粒尺寸大于靠近焊缝根部的晶粒尺寸,受再结晶影响,焊缝两侧热机影响区处辅助板搭接界面消失。 相似文献
68.
石墨烯以其优异的力学、光学、电学、热学性能和独特的二维结构成为材料领域的研究热点。本文主要介绍了石墨烯特性、石墨烯制备方法及其在陶瓷基复合材料中的应用。其中,其制备方法包括机械剥离法、化学还原法、化学气相沉积法及晶体外延生长法等;石墨烯在陶瓷复合材料中的应用可显著提高其物理性能。 相似文献
69.
采用磁控溅射方法在单晶Si(100)上制备LiCoO_2薄膜并选择不同退火温度、保温时间和退火气氛对薄膜进行热处理,研究不同退火条件对LiCoO_2薄膜形貌、组成、晶体结构和力学性能的影响。结果表明:退火过程将LiCoO_2薄膜表面粗糙度从11.63 nm降低至6.13 nm,且退火气氛对LiCoO_2薄膜表面形貌影响最大;LiCoO_2薄膜退火产生Li_2O、CoO、Co_3O_4等副产物,薄膜组成被破坏;任一退火条件均能使LiCoO_2薄膜结晶,平均晶粒尺寸约为30 nm,退火温度对LiCoO_2薄膜晶粒尺寸和残余应力影响最大;LiCoO_2薄膜退火后,其硬度H、杨氏模量Er增大一个数量级,最优退火工艺下(600℃,60 min,纯O_2气氛),H~3/E_r~2比例为0.03 GPa,抵抗塑性变形能力好。 相似文献
70.
钛合金和铝合金均具有质轻、比强度高和抗腐蚀性能好等优点,已广泛应用于航空航天、军事工业和公共交通等领域,钛/铝异种金属复合结构的连接逐渐成为研究热点。然而,由于物理和化学性能差异明显,钛/铝焊接难度大,存在成形困难、接头性能较差等问题。搅拌摩擦焊作为一种固相焊接方法,对克服异种材料性能差异带来的焊接困难具有极大的优势。本文综述了钛/铝异质金属搅拌摩擦焊的研究现状,主要涉及焊缝成形、焊接参数、力学特征、冶金结合和连接机制等,以及衍生的搅拌摩擦焊新技术,为钛/铝异质金属结构的轻量化设计提供新思路,并对其未来发展进行了展望。 相似文献