基于多项式平方和规划的航空发动机鲁棒LPV/PI控制

针对航空发动机常规(proportion integration,PI)控制器设计过程中难以保证鲁棒性及参数适应性差等问题,提出了一种基于线性变参数(linear parameter varying,LPV)模型及多项式平方和(sum of squares,SOS)规划的控制器设计方法.结合传递函数模型下的鲁棒稳定条件及弱对偶定理给出了多项式描述的LPV模型鲁棒稳定条件,并转化为便于求解的SOS规划问题.根据发动机非线性模型获取不同转速下的传递函数模型,并利用多项式拟合的方法建立发动机LPV模型.根据所提出的定理构造出SOS规划问题,并求解得出LPV/PI控制器.最终以某型双轴涡扇发动机为被控对象,在包线内不同点进行了阶跃仿真,结果表明:高压转子转速控制系统的稳态误差为0,调节时间小于3s.      

X射线脉冲星导航硬件脉冲轮廓累积研究

为了在X射线脉冲星地面实验系统仿真源模拟产生X射线的基础上,能够快速稳定地得到脉冲轮廓,采用硬件历元叠加的方法获得脉冲轮廓。研究了用硬件实现历元叠加及其数据整合的算法,该算法首先在MATLAB现场可编程逻辑阵列(FPGA)中实现,再通过MATLAB硬件描述语言(HDL)代码生成模块把算法转换成HDL,经编译后获得配置硬件的Bit文件,最终在开发板FPGA上实现数据处理的硬件模块。一段时间内的光子到达时间数据通过MATLAB算法得到的脉冲轮廓数据与通过硬件模块处理后得到的数据结果存在误差,在单个时间窗口内误差最大值为2个光子数,误差平均值占光子数统计平均值的0.084%;两组统计的脉冲轮廓数据中不同数据占总数据个数的9.481%,这样的误差不影响后端模拟导航模块的导航。利用硬件实现的历元叠加及其数据整合模块具有处理速度快、设备紧凑、功耗低的特点,为航天器利用X射线脉冲星导航提供了一种可行的硬件数据处理技术上的支持。     

存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

世界航空制造产业链中的“中国制造”和“中国创造”——哈飞空客复合材料制造中心成功交付首件空客A350XW B方向舵

全球领先的飞机制造商空客设计、制造的最新机型——A350XWB宽体飞机是目前全球最先进的远程宽体飞机。A350XWB宽体飞机机身大量使用轻型复合材料,大大降低了飞机重量,从而大幅度降低燃油消耗和碳排放。复合材料的使用是当前及未来飞机制造的发展方向。空客公司和中航工业哈飞等中国合作伙伴的合资企业——哈飞空客复合材料制造中心是亚洲最大的复合材料制造企业,采用全球最先进的设备和制造流程,其工人经过严格的培训,为空客A350XWB宽体飞机制造升降舵、方向舵和机腹整流罩等重要部件。继成功交付A350第19段维护舱门和升降舵等部件之后,2014年12月12日,哈飞空客复合材料制造中心交付A350的另一重要部件——方向舵。该制造中心未来将成为空客A350升降舵、方向舵、机腹整流罩和第19段维护舱门的全球独家供应商。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.