Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

K8、JK8机翼接头与检验量规协调准确度的提高

分析了 K8、 JL8机翼接头孔精加加后与检验量规位置协调的条件，介绍了为提高它们之间协调准确度所采取的措施及其效果。     

The double-pulsar binary J0737–3039

A recent multibeam pulsar survey of the outer Galactic plane at Parkes has discovered the first-known double-pulsar binary, a very compact double neutron star system in which both stars are observable as radio pulsars. In this review, we briefly describe the discovery and the studies which have been enabled by the unique properties of the system. These range from the most precise confirmation yet of the theory of general relativity, with the possibility of even more new tests and the measurement of second-order post-Newtonian effects, to studies of the magnetospheres and emission properties of the two pulsars. The discovery also results in a significant increase in the expected rate of occurrence of the mergers of double neutron star systems, and hence the rate of detection of such events by the new ground-based gravitational wave detectors.     

为中国开发太空探路 创中国首飞太空记录——纪念T-7系列探空火箭首次发射成功45周年

在中国第一个实用探空火箭系列——T-7系列探空火箭首次发射成功45周年之际，回顾了该系列火箭的研制由来和基本情况，论述了该系列火箭对中国开发中层大气和太空所起到的探路作用。     

腐蚀对sic/Al(L2)和sic/Al-Ni复合丝力学性能的影响~①

本文对SiC/Al(L2)和SiC/A1-Ni复合丝在蒸馏水和在3.5％NaCl溶液中的耐腐蚀性能进行了研究。通过测试腐蚀前后复合丝的抗拉强度,利用气相色谱、发射光谱、X射线衍射等手段分析腐蚀气体和腐蚀产物,观察金相和扫描电镜下形貌的变化,发现SiC/A1复合丝在室温蒸馏水中36天、50℃和75℃蒸馏水中各15天浸泡后,其抗拉强度基本保持不变,说明该类复合材料对潮湿环境具有良好的耐腐蚀性能;SiC/A1-Ni复合丝在3.5％NaC1溶液中浸泡后,其抗拉强度随溶液温度升高和时闻延长而逐渐下降;其腐蚀主要是选择性腐蚀,其次是孔蚀和缝隙蚀。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

300M钢纯洁度磁粉检验磁痕现象的分析

采用交、直流磁粉检验并结合金相试验、电子探针试验及微量元素含量分析的方法，对３００Ｍ钢磁痕现象的本质进行了分析。结果表明，采用磁粉检验方法对航空优质钢进行纯洁度检验是可信的。     

国家财政主要支出项目与各项税收收入的最优化--回归分析在最优化中的应用研究实例

利用回归分析方法得到国家财政部分主要支出项目，部分税收收入与国内生产总值构成的回归方程，由此构成线性规划问题的约束方程组。再用M单纯形法求最优解。     

串置双五分量天平的研制

本文介绍风洞应变天平中首次研制成功的一台串置双五分量天平。串置双天平由一块钢材制成。O_1天平固定在 O_2天平的受力端。O_2天平既能测量左平尾载荷,又能传递由 O_1天平测量的右平尾载荷。正确分析两台天平的受力传力路线和弹性变形的综合位移量,用严谨的数学公式描述两台天平测量的力和传递的力。对这两种力进行数学分解,形成数学模型,写出天平静校公式的数学表达式,并据此研制天平静校设备,分析天平在各分力作用下的弹性位移,写出弹性角公式。上述各点是串置双天平的核心问题。最后经风洞引导性实验证明,串置双天平的原理、方案、受力分析、静校公式等都是正确的。在国内外,串置双天平第一次用于风洞实验,获得了初步成功。     

高频宽范围阻抗测量的一种新方法

本文根据微波网络理论,提出了利用A参量求解高频阻抗的新方法,详细介绍了如何将该方法用于网络分析仪系统测量高频阻抗,并将其测试结果与美国惠普公司生产的专用高频阻抗分析仪HP4191A及该公司最新展出的频谱、网络、阻抗分析仪HP4195A的测试结果作了比较,实践证明,该方法与传统的S参量法相比,大大拓宽了阻抗测量范围,提高了测量精度(能自动地消除联接电缆的影响),且适用于被测件的同轴联接及非同轴联接。此方法对利用各种网络分析仪实现高阻测量具有普遍意义。