变厚度弹性件柔性接头的非线性分析

结合试验数据,采用Mooney-Rivlin模型模拟了柔性接头的弹性件材料;根据非线性理论,采用混合插值有限元法对某一摆角状态下的柔性接头进行了大变形非线性弹性分析,并在此基础上初步探讨了厚度不均匀弹性件对层间应力的影响。计算结果表明,弹性层减薄到一定程度时,层间剪切应力沿宽度方向分布变得均匀,应力值仍集中在2 MPa以下;层间法向应力分布变化较小,呈二次曲线分布,最大值有所降低;其中,接近后法兰的弹性件厚度不均时,对各项应力最大值影响较大。     

7075-T6铝合金厚板FSW焊缝沿厚度方向上的显微组织演变规律

采用金相显微镜（OM）、扫描电镜（SEM）和背散射电子衍射（EBSD）技术表征7075铝合金厚板搅拌摩擦焊（FSW）焊核中心区的微观结构，研究沿焊缝厚度方向上的显微组织演变规律。结果表明，焊核中心区发生了明显的动态再结晶，由原始粗大的板条状组织转变成了细小的等轴晶；随着距焊缝上表面距离的增加，中心区等轴晶晶粒尺寸呈现逐渐增大的趋势。其中，中心区上部4 mm处的晶粒尺寸最小，仅为7.8 μm；底部19 mm处的晶粒尺寸最大，达18.6 μm。中心区动态再结晶分数随距离的增大而逐渐减小，从中心区顶部1 mm处最大值90.4%减小至底部19 mm处最小值57.5%。受动态再结晶影响，焊核中心区主要以大角度晶界（HAGB）分布为主，且中心区大角度晶界随距离的增加呈逐渐降低的趋势；但每一个典型位置处的大角度晶界分布呈现先增大后减小的趋势，且在45°左右时达到最大值；此外，中心区并没有强取向组织产生。同时，焊核中心区主要以细小、弥散的二次析出强化相η相为主，且二次析出强化相颗粒尺寸随距离的增加而呈逐渐增大的趋势，但二次析出强化相颗粒总体数量却呈相反的趋势变化。     

不同边界层厚度下高马赫数进气道自起动过程研究

为了探寻入口边界层厚度变化对高马赫数进气道自起动性能的影响,对简化的二元高马赫数进气道的加速自起动过程进行数值仿真研究,分析了边界层厚度对自起动过程中流场波系结构变化和自起动性能的影响机制,获得了不同边界层厚度下的进气道自起动性能及主分离包高度的变化规律。结果表明:随着边界层相对厚度从0.05增加至0.3,进气道的自起动马赫数一开始保持不变,然后快速增大;相同主流条件下,不起动流场跨越主分离包无量纲压升和主分离包高度随边界层相对厚度的增大均变小;边界层动量损失厚度和跨越主分离包无量纲压升对进气道起动性能影响重大。     

航空发动机双层结构金属机匣的弹道试验

为研究航空发动机双层结构金属机匣在受叶片冲击时的包容性问题,利用滑膛炮试验系统对双层钛合金带不同间隙叠层靶板进行打靶弹道试验。通过28次有效的弹道试验发现:对比内层（迎弹面）、外层靶板厚度相同带间隙组合的试验结果,间隙越大靶板抗侵彻能力越差;对比不带间隙组合试验结果,内层较薄组合的抗侵彻能力强于内、外层厚度相同组合。采用商业有限元软件ANSYS/LS-DYNA对打靶试验进行了数值仿真,有限元仿真与试验结果吻合较好,并发现内层较薄组合的抗侵彻能力强于内层较厚组合,且两者均强于内、外层厚度相同组合;各个组合在没有间隙的情况下,弹道极限随叶片攻角增加而增加,但是速度曲线突增的攻角有所不同。无量纲靶厚决定了叶片冲击双层靶板的破坏模式。      

Vibration suppression of thin-walled workpiece machining considering external damping properties based on magnetorheological fluids flexible fixture

Milling of the thin-walled workpiece in the aerospace industry is a critical process due to the high flexibility of the workpiece. In this paper, a flexible fixture based on the magnetorheological(MR) fluids is designed to investigate the regenerative chatter suppression during the machining.Based on the analysis of typical structural components in the aerospace industry, a general complex thin-walled workpiece with fixture and damping constraint can be equivalent as a rectangular cantilever beam. On the basis of the equivalent models, natural frequency and mode shape function of the thin-walled workpiece is obtained according to the Euler–Bernoulli beam assumptions. Then,the displacement response function of the bending vibration of the beam is represented by the product of all the mode shape function and the generalized coordinate. Furthermore, a dynamic equation of the workpiece-fixture system considering the external damping factor is proposed using the Lagrangian method in terms of all the mode shape function and the generalized coordinate, and the response of system under the dynamic cutting force is calculated to evaluate the stability of the milling process under damping control. Finally, the feasibility and effectiveness of the proposed approach are validated by the impact hammer experiments and several machining tests.     

人造硬壳层扩散作用的研究

主要研究人造硬壳层的扩散作用，运用有限元模拟的方法，在规范规定的基础上确定出了应力扩散角，且得出加肋梁后应力扩散角基本不变的结论。讨论了加肋梁后固化双层地基的硬壳层等效厚度，为工程应用提供参考。     

钛合金蜂窝三层结构的扩散焊接研究

介绍了俄罗斯钛合金蜂窝三层结构扩散焊接的研究成果.详细介绍了铝合金、焊接规范选择、接头应力变形状态的分析、模拟计算等,有助于国内钛合金的焊接研究.     

Lunar geophysical parameters inversion based on gravity/topography admittance and particle swarm optimization

This paper presents a FORTRAN computer program. The program as code will be used for lunar parameter inversions based on gravity/topography admittance. This will be done by assuming that the lunar lithosphere is modeled as a thin elastic spherical shell. The parameters discussed here include; load ratio, crustal thickness, subsurface load depth, crustal density and elastic lithosphere thickness. The admittance of the best-fitting model can be found through automatically adjusting misfits between one theoretical admittance and an observed one. The results in this paper indicate that this research’s theoretical model is reasonable for exploring the best-fitting parameters. In addition, this code is not only able to automatically and simultaneously calculate the global optimum solution of the parameters studied, but also performs well in computational speed. The code can be easily modified to include more parameter inversions; such as the inversion for subsurface density anomaly and the case of considering infilling material in some lunar mare basins.     

空心长轴深孔加工工艺研究

以某发动机空心长轴零件深孔加工为研究对象,设计了长径比为15,长度超过1米的整体硬质合金刀杆,在某加工项目试验中,应用这种超长整体硬质合金刀杆,在细长比大于10的空心长轴的深孔镗削加工中,改变了传统的深孔加工工艺,满足了空心长轴深孔加工中严格的壁厚差要求,取得了明显的效果.     

薄壁零件数控加工工艺质量改进方法

 提出了通过数控加工前期的预防性仿真 (包括几何仿真与物理仿真 )分析与减小工件变形的数控工艺设计过程范式,将工件视为弹性体,模拟实际加工中的工艺约束,建立工艺模型,通过有限元分析检查变形引起的微观误差。并根据工艺成本代价,依次采取进给量局部调整、刀具路径修正、改进装夹方案、改进毛坯结构工艺性 4种策略,减小或消除加工变形误差,达到逐步改进工艺质量的目标。以某薄壁口框验证了通过预防性仿真改进工艺质量的有效性。