双三相永磁同步发电机多目标优化设计

为实现双三相永磁同步发电机(PMSG)的低固有电压调整率、高发电效率和低成本的特性,研究了侧重于降低固有电压调整率的多目标优化设计方案。采用解析法建立单元电机磁链模型,以永磁体磁化方向长度、永磁体所跨弧长和单元电机相绕组匝数为设计变量,分析上述参数对固有电压调整率、发电效率等评价指标的影响,并提出了基于权重系数的多目标优化函数。分别用标准遗传算法(SGA)、差分进化算法(DE)和基于以上2种算法的混合遗传算法(HGA)优化设计参数并进行对比。试验结果表明,HGA优化效果与设计目标具有良好的一致性,与初始设计参数相比,优化后的电机输出能力以及稳压能力均有所改善。     

浅析减小三自由度陀螺传感器零位的工艺方法

介绍了三自由度陀螺应用特点,简述了角传感器结构及工作原理。从设计理念和实际制造工艺过程分别分析了零位超差、斜率不对称的原因,针对理论上存在的零位偏差从工艺上采用选配方法实现满足对称设计目的,以期望减小传感器零位,提高传感器输出的陀螺零位精度。经实践验证,工艺选配控制方法和流程有效,效果明显,可供其他陀螺借鉴应用。     

无槽环形绕组轴向磁通永磁电机空载反电动势解析

无槽环形绕组有两种类型,即扇形绕组和矩形绕组。针对这两种绕组空间分布对空载反电动势的影响,分别对两种绕组轴向磁通永磁电机的空载反电动势进行了解析推导。在气隙磁密解析计算时,提出通过建立虚拟等效直线电机模型用以计算气隙磁场端部效应函数。为了验证解析公式的正确性,以一台电机方案为例,利用推导的解析公式对空载反电动势进行了计算,与有限元计算结果进行了对比,结果表明解析计算结果和有限元计算结果相对误差小于2.1%,满足工程要求。因此,推导的空载反电动势解析公式可以作为电机设计人员参考使用。     

复合材料气瓶铝内衬缺陷对疲劳及爆破性能的影响

研究了复合材料气瓶在生产过程中金属内衬存在的凹坑、裂纹以及腐蚀等的缺陷类型,并且对存有以上缺陷类型的复合气瓶进行疲劳及爆破实验,研究其对气瓶的性能影响.结果表明:金属内衬缺陷的存在会使得气瓶在承受内压载荷的过程中,金属内衬在缺陷位置出现应力集中,提前出现裂纹的扩展,使得金属内衬失效,无法充分发挥复合材料层高强度的优势,使得复合材料气瓶的疲劳失效次数及爆破强度大大降低,影响最终的使用性能.     

预浸带缠绕过程缠绕层温度场变化研究

为了研究工艺参数对复合材料缠绕层的温度分布的影响,采用经典热力学理论针对预浸带缠绕过程中的传热机制进行分析;基于缠绕过程中的周期性变化规律,同时以变化的旧层初始温度为传热模型的初始边界条件,构建预浸带缠绕温度分布模型,并通过Matlab编程获得一维热传递模型的精确数值解。理论分析了缠绕初始温度、缠绕速度及芯模温度对缠绕层温度变化的影响。结果表明,对缠绕层温度影响程度依次为芯模温度>缠绕速度>缠绕初始温度;而且无论影响参数如何变化,缠绕层的温度分布始终为内层温度较低,并随着径向位置增大,缠绕层温度也在逐渐升高,直到外层最高温度。此外,通过实验对比分析,说明该温度分布模型满足工程要求,可为缠绕工艺研究提供指导。     

Research of Optical Fiber Coil Winding Model Based on Large-deformation Theory of Elasticity and Its Application

Optical fiber coil winding model is used to guide proper and high precision coil winding for fiber optic gyroscope (FOG) application. Based on the large-deformation theory of elasticity, stress analysis of optical fiber free end has been made and balance equation of infinitesimal fiber is deduced, then deformation equation is derived by substituting terminal conditions. On condition that only axial tensile force exists, approximate curve equation has been built in small angle deformation scope. The comparison of tangent point longitudinal coordinate result between theory and approximation gives constant of integration, and expression with tangent point as origin of coordinate is readjusted. Analyzing the winding parameters of an example, it is clear that the horizontal distance from the highest point of wheel to fiber tangent point has millimeter order of magnitude and significant difference with fiber tension variation, and maintains invariant when wheel radius changes. The height of tension and accurate position of tangent point are defined for proper fiber guide. For application to fiber optic gyroscope, spiral-disc winding method and nonideal deformation of straddle section are analyzed, and then spiral-disc quadrupole pattern winding method has been introduced and realized by winding system. The winding results approve that the winding model is applicable.     

双绕组异步发电机励磁控制的优化

定子双绕组异步发电机控制绕组接励磁调节器,只提供发电机励磁无功功率。在风力发电、飞机发电等系统中,转速变化范围较宽,控制绕组无功变换器的容量最小有助于降低系统的成本,功率绕组励磁电容的大小直接影响着控制绕组的无功容量。文章研究了变速变载运行时励磁电容的取值对于控制绕组无功容量的影响规律,对电机参数的影响作了分析。     

Multi-objective optimization of different dome reinforcement methods for composite cases

A multi-objective optimization method was proposed for different dome reinforcement methods of a filament-wound solid rocket motor composite case based on a Radial Basis Function (RBF) model. Progressive damage of the composite case was considered in a simulation based on Hashin failure criteria, and simulation results were validated by hydraulic burst tests to precisely predict the failure mode, failure position, and burst pressure. An RBF surrogate model was established and evaluated by Relative Average Absolute Error (RAAE), Relative Maximum Absolute Error (RMAE), Root Mean Squared Error (RMSE), and R² methods to improve the optimization efficient of dome reinforcement. In addition, the Non-dominated Sorting Genetic Algorithm (NSGA-II) was employed to establish multi-objective optimization models of variable-angle and variable-polar-radius dome reinforcements to investigate the coupling effect of the reinforcement angle, reinforcement layers, and reinforcement range on the case performance. Optimal reinforcement parameters were obtained and used to establish a progressive damage model of the composite case with dome reinforcement. In accordance with progressive damage analysis, the burst pressure and performance factor were obtained. Results illustrated that variable-angle dome reinforcement was the optimal reinforcement method compared with variable-polar-radius dome reinforcement as it could not only ensure the reinforcement angle’s continuous changing but also decrease the mass of composite materials. Compared with the unreinforced case, the reinforced case exhibited an increase in the burst pressure and performance factor of 36.1% and 23.5%, respectively.     

缠绕角度对碳/环氧厚壁管件轴压性能影响的实验研究

文摘采用缠绕工艺制备了20°、30°和40°三种缠绕角度的碳/环氧厚壁管件,通过轴压实验研究了缠绕角度对厚壁管件的轴压模量和轴压强度的影响,并对轴压破坏模式进行了分析。实验测得轴向模量值比有限元模型计算值偏小,破坏模式为纤维层向外崩裂破坏与有限元分析结果一致。     

弯管制造过程中三坐标纤维缠绕机运动分析

在确定弯管及其连接段稳定缠绕线型分布的基础上，利用绕丝嘴与芯模之间相对运动关系，建立纱线的悬纱方程，可进一步解出缠绕机运动轨迹方程。文中研究绕丝嘴作平动时缠绕机的三坐标运动方程，即绕丝嘴的平动方程和芯模转角方程，为计算机控制纤维缠绕机奠定了基础。