Design and Simulation of Electro-hydrostatic Actuator with a Built-in Power Regulator

The electro-hydrostatic actuator (EHA) is a kind of power-by-wire (PBW) actuator that converts the electrical power into localized hydraulic power for flight control. By removing the central hydraulic power supply together with hydraulic pipes, an EHA's reliability and efficiency are greatly improved but its frequency width and stiffness decreased. To overcome the drawback, this article proposes a novel structure of EHA associated with a power regulator. Composed of a high-pressure accumulator and a proportional valve, it can store and harness the hydraulic power flexibly according to the changing control requirements. The concept of transferred volume is put forward to estimate the capability of the power regulator. The actuator output position can be kept fixed with a hydraulic lock. The compounded control is specially developed to ensure the actuator system to operate in a correct manner. The simulation results indicate that the new-brand actuator results in efficient expanding of the system frequency width with an optimal power supply.     

Influence of stealth aircraft dynamic RCS peak on radar detection probability

For modern stealth aircraft, it is important to analyze the influence of Radar Cross Section (RCS) peak exposure on penetration for guiding stealth design and penetration trajectory planning, which needs to reflect the RCS statistical uncertainty and the RCS difference with the change of incident angle. Based on the RCS characteristics of typical stealth aircraft, this paper established a simplified RCS dynamic fluctuation statistical model with the parameters log mean and log standard deviation. According to the detection probability algorithm in radar signal processing field, this paper built the algorithm of radar detection probability based on the RCS dynamic fluctuation statistical model. The analysis of examples concluded that the key to successful penetration is to shorten the RCS peak exposure time, which can be reduced by decreasing the RCS peak width or increasing velocity. Based on the conclusion, this paper proposed the method of turning maneuvering to reduce RCS peak exposure time dramatically.     

双极模式PWM直流可逆调速系统

提出一种双极模式ＩＧＢＴ功率变换电路及直流调速系统，分析了ＰＷＭ可逆调速系统的组成和工作原理，探讨了集成ＰＷＭ控制器和模块驱动电路设计的有关问题，该系统已应用于２ｋＷ以上电动机的可逆调速运行。     

较小功率脉冲YAG激光填丝焊接技术的研究

介绍了利用较小功率脉冲YAG激光做热导焊接的激光填丝焊接技术;并讨论了微型结构件的激光 填丝焊接方法;给出了利用脉冲YAG激光做微型结构件的激光填丝焊接的较佳焊接工艺。     

Using LASCO-C1 spectroscopy for coronal diagnostics

The LASCO-C1 telescope was designed to perform spectral analysis of coronal structures by means of a tunable Fabry–Pérot interferometer acquiring images at different wavelengths. Results from spectral scans of the Fe xiv 5303 Å green coronal emission line are presented. Physical quantities like the ion temperature (line widths), and the flow velocity along the line of sight (Doppler shifts) are obtained over the entire corona.     

单相Z源逆变器控制策略

提出了一种单相Z源逆变器控制策略,该策略由Z源网络电压控制环、交流侧电压瞬时控制环和直流侧电压纹波前馈控制环3部分组成.由于Z源阻抗网络存在非最小相位效应,因此在Z源网络电压闭环控制基础上引入了交流侧瞬时控制,使逆变器获得了较快的响应速度.针对负载较重时Z源网络输出电压波动大的问题,通过电压纹波前馈控制修正调制比,有效抑制了直流侧电压纹波对交流侧的影响,提高了输出交流电压的波形质量.仿真及实验结果均证实了所提出的控制策略的有效性.     

KTP晶体频率转换带宽特性研究

以0．8μm波长作为泵光频率,对KTP晶体在近红外光区的匹配特性作了研究,对各种可能的频率转换关系进行了分析,提出了两个最优宽带转换方式以及获得宽带频率转换的方法。     

斜齿面齿轮齿宽的设计

研究了斜齿面齿轮小端不根切和大端不变尖的问题.给出了任意轴交角条件下小端不产生根切的内半径和大端不变尖的外半径的表达式.提出了在产形齿轮上求解关键点的方法.定义了内半径系数,外半径系数和齿宽系数三个无量纲量,分析表明产形轮齿面螺旋角和小齿轮齿数的大小决定了三个系数的变化趋势.      

一种帆板驱动机构用永磁同步电机微步控制方法

根据磁场定向矢量控制原理,提出一种永磁同步电机微步驱动控制策略.通过保持定子电流矢量幅值不变并均匀改变定子电流矢量的位置,获得大小不变位置均匀变化的定子磁势,从而实现太阳帆板的对日定向.试验结果表明采用所提出的微步驱动控制方法实现了太阳帆板模拟负载的驱动性能,并得出设计过程中应综合考虑整机效率和帆板驱动速度稳定度因素来选取转矩电流给定的结论,也进一步证明了控制方法的有效性,可用于工程实际.     

应用电流控制脉宽调制技术的功率变换器

介绍和分析了 A.G.Bose等提出的 PWM控制技术——电流控制脉宽调制技术 ,以及它在功率变换器中的应用 ,分析了电流控制脉宽调制系统的稳定性问题。实验表明 ,这种功率变换器具有重量轻、体积小、静态精度高、动态响应快等优点 ,有十分重要的应用价值。