计算模拟月壤颗粒吸收及散射特性的一种球叠加模型

针对模拟月壤复杂的外形特征以及多相非均质的微观结构,提出了一种计算模拟月壤颗粒吸收及散射特性的球叠加模型。根据模拟月壤颗粒的形状指数和分形特征识别结果,归纳了4种主要的模拟月壤颗粒类型,并采用蒙特卡罗光线跟踪法研究了这4种颗粒在单色平行光照射下的吸收及散射特性。与已有的非球形颗粒辐射特性的算法比较显示,该模型具有良好的计算准确性。在数值计算的基础上,分析了颗粒尺度参数及光学常数对其自身辐射特性的影响,并通过改变平行光照下的光线入射角度,分析了非球形颗粒的朝向对其自身辐射特性的影响。由计算结果推断,该模型不仅可以应用于计算模拟月壤颗粒的辐射特性,还可以满足其他适用于几何光学近似的非球形粒子。     

粉煤灰颗粒增强铝基复合材料的耐磨性研究

以粒度为80μm的粉煤灰为增强相,粒度为30μm的铝粉为基体,采用粉末冶金法成功制备了粉煤灰颗粒增强铝基复合材料。经SEM、金相显微镜等分析手段对制备的复合材料进行组织观察,并对其进行耐磨性测试。结果表明,粉煤灰含量为20%,烧结温度为650℃时,相对损率最小为0.1590%。随着粉煤灰含量和保压时间的增加,试样的耐磨性逐渐升高,随着烧结温度升高,试样的耐磨性呈现出先升高后降低的趋势。     

含硼富燃燃气燃烧实验研究

为实现固冲发动机二次燃烧模型验证,结合固冲发动机工作条件,设计了一种带透明观察窗燃烧实验装置;营造了简单的燃烧环境,实现了燃烧过程掺混作用的弱化;借助高速摄像进行了以空气速度作为单一变量的含硼富燃燃气燃烧可视化测量,获得了火焰形态结构;采用高速数据采集,获得了燃烧室压力;将实验数据与数值模拟结果进行了对比和分析。结果表明,燃气与空气速度相近时,火焰呈锥角结构,硼粒子的点火距离较长;燃气与空气速度差较小时,同一位置燃烧室压力较大;燃气与空气速度近似程度决定火焰的形态;数值模拟结果与实验结果基本吻合。     

宽粒径范围颗粒对气相膨胀的影响

利用双流体模型对固体火箭发动机喷管内气固两相流进行计算,研究了两相流中颗粒相与气相的相互作用,分析了颗粒粒径及颗粒质量分数对两相流中气相在喷管中膨胀的影响。结果表明,颗粒粒径造成两相流损失的大小是颗粒比表面积、气相湍流动能及颗粒在喷管内的滞留时间等因素共同作用的结果,两相流损失随着颗粒粒径的增大先增大、后减小,同时随着颗粒质量分数增大而增大;JPL喷管中粒径为2μm的颗粒造成的两相流损失最大,此粒径下,当颗粒质量分数从10％增大到40％时,两相流损失从10％增大到26％。     

航天器防护高能带电粒子的新方法

文章介绍了航天器防护高能带电粒子的一种新方法——利用磁鞘进行主动防护。阐述了磁鞘防护高能带电粒子的基本原理,分析了其在工程应用上的可行性,并提出了磁鞘的一种设计方案。针对这种设计方案进行了数值分析计算,结果表明该方案可以有效防护0.15MeV以下的电子。     

超高速机械密封副离子注入与摩擦学特性研究

超高速机械动密封需满足CZ-5运载火箭伺服系统中涡轮泵可靠性及寿命指标要求。离子注入作为重要的金属材料表面改性技术,对有效改善机械密封副旋转环表面摩擦磨损特性至关重要。在对密封动环表面离子注入可行性研究的基础上,提出了对其密封副配对摩擦磨损特性进行综合验证的试验方案。通过选取常用典型石墨与旋转金属环配副进行干磨条件下的试验测试,改变线速度、端面比压,使用摩擦磨损试验机对比分析了配对摩擦副的摩擦磨损特性,系统研究了载荷和转速对密封副配对摩擦系数的影响规律,揭示其密封摩擦学特性。通过机械密封在温度应力下的工作可靠性分析以及密封副整机稳态工作性能验证,为超高速涡轮泵的寿命与可靠性试验验证提供了一个合理的、高效费比的技术途径。     

液体火箭发动机涡轮泵机械密封磨损机理研究

对比分析了机械密封静环端面原始表面和磨损表面形貌,得到了磨损形式和内外径磨损差异;仿真分析了密封端面接触应力及温度场,分析了转速、介质压力等条件对端面接触应力和温度场的影响;探明了端面接触应力和温度变化对磨损性能的影响,阐述了机械密封的磨损机理。     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

铁基金刚石节块的热处理及其耐磨性能研究

首次提出了在烧结型金刚石工具的制造中引入热处理的新工艺，并系统地研究了淬火温度、淬火时间及回火温度等热处理工艺参数对热压烧结型铁基金刚石圆盘锯节块及其胎体材料机械性能的影响，同时对经热处理的铁基金刚石圆盘锯节块在石材旺苍红上进行磨损试验研究。试验结果表明，热压烧结型铁基金刚石圆盘锯节块胎体热处理的最佳工艺参数为：淬火温度为７６０～７９０℃、淬火时间为３．５ｍｉｎ、回火温度为２４５～３１５℃；经热处理后铁基金刚石圆盘锯胎体及节块的强度、硬度等机械性能有显著的提高，热处理也能明显改善铁基金刚石圆盘锯节块的耐磨性能。这说明将热处理工艺用于烧结型金刚石工具的制造中是切实可行的。     

Oxygen line mapping of SN 1006 with Suzaku

SN 1006 is one of the supernova remnants (SNRs) with relatively low-temperature electrons, considering the young age of just 1000 years. We carried out SN 1006 mapping observations with the X-ray Imaging Spectrometers (XIS) and the Hard X-ray Detector (HXD) onboard Suzaku, the fifth Japanese X-ray satellite. Thanks to the excellent spectral resolution of XIS in the soft X-ray band, H-like and He-like oxygen emission lines were clearly detected, and we could make a map of the line intensity, and as well as a flux and the photon index of nonthermal component. We found that these parameters have spatial dependences from region to region in the SNR; the north region is bright in nonthermal, while dim in thermal; the east region is bright in both nonthermal and thermal; the inner region shows dim nonthermal and bright thermal emission. The photon index is the smallest in the north region.