SHS法制备硼化物陶瓷粉体的表征分析

采用自蔓延高温还原合成方法制备TiB2,TiB2-Al2O3和ZrB2-Al2O3陶瓷粉末.利用XRD,XPS,SEM以及TEM等分析测试手段对合成粉末进行表征和分析.结果表明,TiB2,ZrB2和Al2O3分别以主晶相的形式存在于所合成的各自粉体之中.相比之下,TiB2单相陶瓷粉末颗粒分布较宽.由于自蔓延高温合成(SHS)温度很高,部分颗粒形成团聚,宏观上使颗粒的平均粒径变大(＞5μm);而TiB2-Al2O3和ZrB2-Al2O3复合陶瓷粉末,因合成过程中Al2O3的形成,使得颗粒粒度分布明显变窄,分布均匀,颗粒尺寸也相应减小.分析认为这主要与复合粉末合成过程中,不同颗粒间形成良好结合的界面有关.     

等温锻造对Ti-17粉末合金显微组织的影响

采用烧结 等温锻造的方法制备Ti-17粉末合金,对粉末合金制备过程中各工序的密度、显微组织变化规律等进行了试验研究.试验结果表明:经相同条件烧结后,-140目粉末烧结棒材和-80/ 140目粉末烧结棒材分别达到理论密度的98.06%和93.55%,在-80/ 140目粉末烧结棒材显微组织中观察到有大量的残留空隙存在.采用高低温等温锻造工艺能够有效去除粉末合金烧结后残留的空隙,提高合金的密度,使合金的显微组织得到显著细化和均匀化.烧结 等温锻造是制备优质粉末钛合金的有效方法.     

惰性块式平面波发生器形成平面波的数值模拟分析

探讨了惰性块式平面波发生器的相关原理,在费马原理的基础上设计了平面波发生器的物理模型,用非线性有限元方法对平面波形成过程进行了数值模拟,得到了不同时刻的波形图像,数值模拟结果与实际过程在物理宏观特征上基本一致。     

调频连续波SAR成像算法研究

机载遥感微波成像雷达在地球观测特别是在城市应用中起着非常重要的作用,现在人们对体积小、重量轻、成本效益高、分辨率高的成像雷达越来越关注。调频连续波(FM-CW)技术和SAR相结合的调频连续波合成孔径雷达应运而生。论文详细分析了FM-CW SAR的成像过程,提出了去除相位残余的算法,并给出仿真结果。通过仿真可以看出,调频连续波合成孔径雷达具有较好的空间分辨力。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

某小型无人机中长波辐射特性测量及辐射强度反演

随着“自杀式”无人机集群的饱和式攻击在战场上发挥巨大威力,如何有效拦截是各国近年来研究的重要方向,而红外探测是最热门也是最高效的探测拦截手段之一。为此,开展某典型无人机目标中长波红外探测试验,获取典型某无人机目标辐射特性数据,完成中长波红外辐射强度反演。同时,考虑环境变化对红外探测的影响,为使用红外探测手段完成无人机目标拦截提供实测效果演示。本文研究结果可作为论证中长波对无人机目标探测差异的依据,以支撑探测体制的选择。     

基于行波与模态的混合方法对Timoshenko梁进行振动主动控制

 基于Timoshenko梁理论,采用波控制和独立模态空间混合方法,对悬臂梁的振动控制问题进行研究。采用波控制方法实现对Timoshenko梁结构的一点或多点的横向位移的振动控制。首先,基于结构的整体运动,采用模态坐标控制方法,对结构振动进行整体控制设计。而后,基于结构的局部性质,采用波方法吸收结构振动中的高频能量并求出Timoshenko梁中波的反射因数和透射因数。理论上研究了单位力扰动下的悬臂梁的振动。考虑的具体方法是将PD反馈波控制与基于极点配置法设计的模态控制相结合。最后给出数值结果。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

线性调频连续波SAR成像算法研究

研究了线性调频连续波SAR的距离徙动算法成像.针对线性调频续波SAR的特点,在STOP AND GO近似成立的条件下,讨论距离徙动算法的实现过程.STOP AND GO近似失效时,通过补偿线性调频连续波SAR连续运动引入的多普勒频移,提出了改进,并给出仿真验证.