高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。     

雷达信号时差频差测量定位工程实现技术研究

针对星载时差频差无源定位系统对地海面雷达信号定位工程实现需要考虑的实际问题,对雷达信号时差频差测量关键技术进行研究.首先研究了雷达信号时差频差测量方法,然后研究了双星时差频差模糊条件并提出解模糊方法,最后,研究了长时间积累对到达频差的影响,给出随时间变化频差补偿方法.     

吉时利2750在真空热试验测量系统中的应用

真空热试验测量系统是空间环境模拟设备的重要分系统.文章对真空热试验测量需求进行了简单介绍,对采用吉时利2750数字多用表实现的1000点测量系统进行了说明,主要包括:测量系统的结构设计和通讯方式选择、测量信号输入多路转换开关的选择、测量信号输入分线箱设计,提出了一种多主机并行的快速测量方法,并给出了测量参数.应用结果表明:该系统运行稳定可靠,测量数据准确无误.     

瞬变流速作用下姿控发动机燃料管路的非线性振动特性分析

为研究瞬变流速激励下某型卫星姿控发动机燃料输送管路的非线性振动特性,采用加权余量法和四阶Runge—Kutta法对燃料输送管路的非线性液固耦合振动模型进行了数值仿真,研究不同燃料流速下、电磁阀开关时长对燃料管路非线性振动稳定性的影响.仿真结果表明,依据管路特征线可将管路振动分为稳定振动区和不稳定振动区,且不稳定振动主要...     

电磁测力系统研究

介绍了电磁测力系统中静磁场分析与优化、通电线圈位置控制方法及提高线性度的自校准方法。运用Maxwell 3D进行仿真计算,得到了相对优化的磁密及磁均匀性,通过控制通电线圈在磁场中位置及分段线性微分技术,提高了电磁测力准确度。构建了试验装置,对比试验数据表明,该研究措施对于提高电磁测力准确度取得了较好效果。     

火星大气来流模拟装置CFD仿真与试验

根据我国火星着陆巡视器工作过程,其着陆发动机需要在相对火星大气高速迎风运动中可靠点火。由于巡视器着陆时发动机喷管出口气流与火星稀薄气流方向相反,目前无法通过理论计算准确获得着陆过程的动态流场对发动机起动过程的影响量值。为验证火星着陆环境下发动机点火的适应性,需要建立发动机的火星大气来流试验环境模拟条件。为模拟发动机在火星大气条件下的相对运动,在真空舱内发动机保持固定,前端设置环形来流形成装置,该装置在发动机喷管周围形成一定速度的逆向来流包络。采用数值模拟技术结合试验验证方法,在火星着陆器巡视器主发动机性能考核试验中,针对来流的形成装置开展了设计研究工作。来流模拟试验测试数据表明:在确保贮箱供应压力稳定的条件下,来流模拟系统能够形成100~200 m/s速度的稳定来流,发动机在来流下能稳定启动工作,真空舱压力满足试验要求。     

无人车基于激光雷达/视觉的目标体积自动测量方法

近些年,基于激光雷达和视觉的目标感知在无人系统中得到了广泛应用。目标的体积测量在很多应用场景可以发挥极其重要的作用,然而对识别感知目标的体积测量,目前尚无大量研究。首次提出了一种基于激光雷达/视觉的无人车目标体积自动测量方法,实现了无人车与目标体积测量功能的结合。通过在LeGO-LOAM算法中加入点云畸变补偿,相较于原始LeGO-LOAM算法,无人车在高速情况下的构图精度得到提升;通过将激光雷达与视觉进行深度融合,实现了目标的自动识别与全局定位;通过基于平面拟合的地面分割与欧式聚类,实现了目标点云轮廓的实时获取;通过设计一种基于切片法的不规则物体体积测量方法,实现了无人车在运动情况下对目标体积的自动估计。最终,分别通过Gazebo仿真和实际试验验证了算法的有效性。试验结果表明,所提算法在无人车运动的情况下对静态目标物的实时体积测量精度优于3%,具有较好的工程应用价值。